Ionic conductivity and mechanical properties of a mixed polymer matrix consisting of poly(ethylene glycol) (PEG) and cyanoresin type M (CRM) with various lithium salts and plasticizer were examined. The CRM used was a copolymer of cyanoethyl pullulan and cyanoethyl poly(vinyl alcohol) with a molar ratio of 1:1, mixed plasticizer was ethylene carbonate (EC) and propylene carbonate (PC) at a volume ratio of 1:1. The conductive behavior of polymer electrolytes in the temperature range of $298{\sim}338\;K$ was investigated. The $PEG/LiClO_4$ complexes exhibited the highest ionic conductivity of ${\sim}10^{-5}S/cm$ at $25^{\circ}C$ with the salt concentration of 1.5 M. In addition, the plasticized $PEG/LiClO_4$ complexes exhibited improvement of ionic conductivity. However, their complexes showed decreased mechanical properties. The improvement of ionic conductivity and mechanical properties could be obtained from the polymer electrolytes by using CRM. The highest ionic conductivity of PEG/CRM/$LiClO_4$/(EC-PC) was $5.33{\time}10^{-4}S/cm$ at $25^{\circ}C$.

In order to improve the water swelling, thermal/mechanical and adhesion properties of waterborne polyurethane (WBPU), a series of the crosslinkable WBPUs containing hydrophilic ionic component, dimethylol propionic acid (20 mole%), were prepared by in-situ polymerization using a cross-linker hexakis (methoxymethyl) melamine (HMMM). Effects of the HMMM content (2, 4, and 6 wt%) and curing temperature on these properties of the crosslinked WBPUs samples were investigated. All properties were found to increase with increasing HMMM content. It was found that the optimum curing temperature of the WBPU films and adhesives was near $120^{\circ}C$, which was not dependent on the HMMM content.

Coating the fibre surface by in situ oxidative chemical polymerisation of polypyrrole (using $FeCl_3$ as oxidant) is a readily industrial applicable way to give electrical properties to wool with good ageing stability [1], although pre-treatments are required to avoid damage of the cuticle surface due to the acidic condition of the process. FT-IR and EDX analysis reveal that organic sulphonates and sulphates, used as dopants, are absorbed by wool, while chlorine ions are preferably embedded on the polypyrrole layer. The resulting electrical conductivity seems mainly due to the presence of chlorine as counter-ion of polypyrrole; nevertheless, the presence of arylsulphonate in the polymerisation bath increases the electrical conductivity of the coating layer.

Caprolactam is the most important raw material for making Nylon 6 fibers and its quality directly determines the quality of Nylon. So it is necessary to study the techniques and methods to remove the colorful impurities from caprolactam. In this paper, the decolorization of caprolactam aqueous solution by anion exchange resins was studied and the decoloring abilities of five commercial resins were investigated. The regeneration of the resins was also studied, too. This study shows that the resin AMTX202 have excellent decoloring ability in the column experiment and that the decoloring efficiency is correlated with the volume of resins packed and is slightly affected by the flow rate and regenerating times. The fact that the resins can be regenerated and reused without affecting the efficiency of decolorization will decrease the cost of the treatment and operation in the industry. The adsorption of colored compounds with anion exchange resins in the packed columns seems to be technically feasible.

The dye-resist effect and leveling properties of hetero-mulifunctional dye-resist agents in acid dyeing of wool were investigated. The dye-resist agent with dichlorotriazinyl group achieved better resist effectiveness than those with monochlo-rotriazinyl group. The resist effectiveness was improved by increasing the number of sulfonate group in dye-resist agents. Also, the resist agents with more sulfonate groups showed better dye-assist effectivness, attributable to the increased electrostatic attraction between dye-resist agents and the cationic dye. However, the leveling properties of dye-resist agents decreased with the number of sulfonate groups in the molecule.

The present study aims at characterizing and modeling the anisotropic creep behavior of coated textile membrane, a class of flexible textile composites that are used for moderate span enclosures (roofs and air-halls). The objective is to develop a creep model for predicting the lifetime of coated textile membrane. Uniaxial creep tests were conducted on three off-axis coupon specimens to obtain the directional creep compliance. A potential with three parameters is shown to be adequate for modeling the anisotropic creep behavior of coated textile membrane. Furthermore, a possibility of predicting the creep deformation of coated textile membrane in a multi-axial stress state is discussed using the three-parameter potential.

Using a strain-controlled rheometer, the steady shear flow properties of aqueous xanthan gum solutions of different concentrations were measured over a wide range of shear rates. In this article, both the shear rate and concentration dependencies of steady shear flow behavior are reported from the experimentally obtained data. The viscous behavior is quantitatively discussed using a well-known power law type flow equation with a special emphasis on its importance in industrial processing and actual usage. In addition, several inelastic-viscoplastic flow models including a yield stress parameter are employed to make a quantitative evaluation of the steady shear flow behavior, and then the applicability of these models is also examined in detail. Finally, the elastic nature is explained with a brief comment on its practical significance. Main results obtained from this study can be summarized as follows: (1) Concentrated xanthan gum solutions exhibit a finite magnitude of yield stress. This may come from the fact that a large number of hydrogen bonds in the helix structure result in a stable configuration that can show a resistance to flow. (2) Concentrated xanthan gum solutions show a marked non-Newtonian shear-thinning behavior which is well described by a power law flow equation and may be interpreted in terms of the conformational status of the polymer molecules under the influence of shear flow. This rheological feature enhances sensory qualities in food, pharmaceutical, and cosmetic products and guarantees a high degree of mix ability, pumpability, and pourability during their processing and/or actual use. (3) The Herschel-Bulkley, Mizrahi-Berk, and Heinz-Casson models are all applicable and have equivalent ability to describe the steady shear flow behavior of concentrated xanthan gum solutions, whereas both the Bingham and Casson models do not give a good applicability. (4) Concentrated xanthan gum solutions exhibit a quite important elastic flow behavior which acts as a significant factor for many industrial applications such as food, pharmaceutical, and cosmetic manufacturing processes.

Cotton fabric was treated with montmorillonite (MMT) so as to evaluate its effectiveness on improving its wrinkle resistance. The MMT in emulsion form was applied to cotton fabric by padding and finally the wrinkle resistance of the MMT-treated cotton fabric was improved. Furthermore, instrumental methods were used for studying the presence of MMT particles on the cotton fabric surface. It was noted that nano-scale MMT particles adhered on the fiber surface and the particle size played an important role in influencing the wrinkle resistance of the cotton fabric. The experimental results are discussed thoroughly in this paper.

Traditional spinning systems have reached profitability limits in developed countries due to high production costs and low system productivity. Pneumatic spinning is seen as a developing system, because productivity is much higher than conventional systems. This study evaluates one of the main problems to increase productivity in pneumatic spinning, where air mass-flow is dragged by the drafting cylinders. This flow interacts with the incoming fibres deviating them from their expected path. Via laser anemometry, airflow velocity distribution around drafting cylinders has been measured and it has been found that vorticity is created at the cylinder's inlet. Extensive CFD simulation on the air flow dragged by the cylinders has given a clear insight into the vortex created, producing valuable information on how cylinder design affects the vorticity created. Several drafting cylinder designs have been tested without giving any improvement in productivity. However, the use of a drafting cylinder with holes in it produced good results to the problem of air currents, strongly reducing them and therefore allowing a sharp increase in yarn quality, as well as an increase in productivity. An extensive study on vortex kinematics has been undertaken, bringing with it a better understanding of vortex creation, development and breakdown.

Standard extraction procedure for examining chromophoric substances of turmeric was investigated. Acetone and methanol were used as extracting solvents with different extraction procedures and pH levels. GC-MS analysis identified curcumene 2 (6.7 min), feruloylmethane 3 (8.3 min), coumaran 4 (6.09 min), vanillin 5 (6.2 min), and zingiberene 6 (10.5 min) as the major products. Curcumin 1 which has been known as the major chromophoric substance of turmeric was not detected in any samples. The maximum amount of curcumene 2, which was used as the fingerprint product for turmeric dye, was obtained by utilizing presoaking and decanting step with methanol prior to actual extraction step using a waterbath shaker (WMM). The highest relative abundance of curcumene 2 was detected in pH 6 sample followed by pH 5 indicating that the most appropriate pH level was in the range of pH 6-5.

Three vat dyes have been applied to regular viscose rayon and their dyeing and wash fastness properties were evaluated. Particle size determination was undertaken to obtain information about the size of dye particles converted by a reducing agent, to see if dye particle size has an affect on dyeing properties of regular viscose rayon. It is observed that viscose rayon exhibits more dyeability with reducing agent concentrations between 5-7.5 g/l. Also, we found that the vat dyeing system is greatly affected by the particle size of the vat dye converted to leuco form by a reducing agent.

Six nano disperse dyes were prepared using corresponding O/W nanoemulsions which were obtained with sodium laurylsulphate and caprylic triglyceride. The average particle size of the dyes prepared were in the range of $110{\sim}130nm$. Exhaust dyeing using nano dyes resulted in low exhaustion yields of $17{\sim}26%$ on regular polyester fiber and $28{\sim}38%$ on ultramicrofiber polyester. The observed low exhaustion yields of nano disperse dye can be explained by the solubilization of dye particles into surfactant micelles as well as the high stability of the nanoemulsions, these might reduce the capacity of dye uptake onto the fibers. However, higher K/S values of dyeings with nano dyes on ultramicrofiber sites compared to those on regular polyester sites suggested their potential to be more efficient dyes for finer denier microfiber polyesters.

Dyeing and color fastness properties of a reactive disperse dye containing an acetoxyethylsulphone group on PET, Nylon, silk and N/P fabrics were examined. The reactive disperse dye exhibited almost the same dyeing properties on PET fabric as a conventional disperse dye except the level of dye uptake. The most appropriate pH and dyeing temperature for the dyeing of Nylon fabric were 7 and $100^{\circ}C$ respectively. The build-up on Nylon fabric was good and various color fastnesses were good to excellent due to the formation of the covalent bond. Application of the reactive disperse dye on silk fabric at pH 9 and $80^{\circ}C$ yielded optimum color strength. The rate of dyeing on Nylon fabric was faster than that on PET fabric when both fabrics were dyed simultaneously in a dye bath, accordingly color strength of the dyed Nylon was higher. The reactive disperse dye can be applied for one-step and one-bath dyeing of N/P mixture fabric with good color fastness.

A pineapple protease, bromelain, was used to improve the dyeing properties of protein fibers such as wool and silk. The optimal condition for the activity of the pineapple protease was about $60^{\circ}C$ at pH 7. The wool and silk were treated with the protease extracted from a pineapple and the K/S values of the dyed wool and silk were measured using a spectrophotometer in order to compare the dye uptake. The protease treatment enhanced the dyeing properties of protein fibers without severe changes in mechanical properties. The surface appearances of protease-treated fibers were observed by microscopy.

The application of a degassing system to mercerization process was investigated. It was found that the physical properties of cotton fabrics mercerized in the degassed NaOH solution were superior to those mercerized in NaOH solution. The degree of penetration of the degassed water was examined by measuring wicking height. The wicking height in the degassed water without the wetting agent is higher than that of the saturated water with 0.1 % of wetting agent.

This paper adopts nonlinear vibration method to analyze the fluctuation process of fiber movement. Based on Hamilton Principle, this paper establishes differential equation of fiber axial direction movement. Using variable-separating method, this paper separates time variable from space variable. By using the disperse movement equation of Galerkin method, this paper also discusses stable region of transition curve and points out those influencing factor and variation trend of fiber vibration.

Tight-fitting clothing pattern reflecting the accurate information of the 3D body shape has been one of the challenges for garment industry, however, fitting problems still exist. The objectives of the paper is to develop a 2D pattern which fits tightly to the 3D human scan data for sports suits that need comfort and function for maximum performance. In this study, the user graphic interface application software for the semi-automatic garment pattern generation has been implemented using the triangle simplification scheme together with 2D projections of free-falling of 3D surface polygons keeping the original 3D surface area preservation. A typical application of the developed pattern to the functional body suits is presented and verification of the proposed method is also provided.

The purpose of this study was to examine the effects of the structural properties of plain knit fabrics on the subjective perception of textures, sensibilities, and preference among consumers. This study, then, aimed to provide useful information with respect to planning and designing knitted fabrics by predicting the subjective characteristics analyzed according to their structural properties. For this purpose, we employed statistical analysis tools, such as factor and regression analysis and an adaptive-network-based fuzzy inference system(ANFIS), thereby combining the merits of fuzzy and neural networks and presupposing a non-linear relationship. Through factor analysis, we also categorized the subjective textures into 'roughness', 'softness', 'bulkiness' and 'stretch-ability' with R2=70.32%: and categorized the sensibilities into 'Stable/Neat', 'Natural/Comfortable' and 'Feminine/Elegant' with R2=68.12%. We analyzed subjective textures, sensibilities, and preference with ANFIS, assuming non-linear relationships; consequently, we were able to generate three or four fuzzy rules using wool/rayon fiber content and loop length as input data. The textures of roughness and softness exhibited a linear relationship, but other subjective characteristics demonstrated a non-linear input-output relationship. Compared with linear regression analysis, the ANFIS exhibited had higher predictive power with respect to predicting subjective characteristics.

The effect of cashmere yarn twist, knitted fabric density, and cashmere properties on pilling rates of cashmere knitted fabric is investigated in this paper. The experimental results show that yarn twist and fabric density have little influence on pilling rates of cashmere knitted fabric for yarn 38.4 tex/2 when yarn twist varies from 234 T/m to 272 T/m, and the fabric density is 9.7, 10.7, and 11.2 yarns/inch, respectively. The length of cashmere fiber, in particular less than 7.5 mm, is responsible for the pilling rates of cashmere knitted fabric based on optimal scaling regression analysis.