Journal of the Korean Geotechnical Society (한국지반공학회논문집)

Korean Geotechnical Society (한국지반공학회)
권호 표지
DOI QR코드

DOI QR Code

Study on the Effect of Pile Tip Shape on Driven Pile Behavior Using 3D Printers

3D 프린터를 이용한 선단 모양 변화에 따른 타입말뚝 거동 연구

  • Kim, Dohyun (Dept. of Civil and Environment Engrg., Hanbat National Univ.)
  • 김도현 (국립한밭대학교 건설환경공학과)
  • Received : 2023.01.02
  • Accepted : 2023.01.16
  • Published : 2023.01.31
Download PDF
⟨ Previous Next ⟩

Abstract

In this study, the impact of pile tip geometry, including shape, size, and angle, on the drivability and stress concentration during pile driving was investigated using 3D printing technology and finite element numerical analysis. A series of field loading tests were conducted on a test pile with various pile tip conditions, including width, angle, and shape. The changes in settlement were quantified as a ratio to the settlement of a conventional pile tip case and large deformation finite element analysis was used to investigate the maximum stress on a pile tip and the location of possible damage during pile driving. The results showed that by modifying the shape, size, and angle of the pile tip, the drivability of the pile could be improved and the maximum stress concentration around the pile tip could be significantly reduced, thereby ensuring the structural integrity of the pile during pile driving.

본 연구에서는 3D 프린팅 기술을 활용하여 타입말뚝 선단의 모양에 따른 관입성 분석을 현장 축소모형시험을 통해 관찰하고, 대변형 수치해석을 통해 타입 중 말뚝 선단에 집중되는 최대응력의 변화를 확인하였다. 3D 프린터를 통하여 다양한 직경, 각도 그리고 모양의 말뚝 선단 모형을 제작하였고, 이를 현장 축소모형시험에 활용하였다. 이를 통해, 말뚝 선단 조건에 따른 말뚝의 침하량의 변화를 관찰하였다. 더 나아가, 대변형 수치해석 기법을 적용하여 다양한 말뚝 선단 조건에 따른 타입 중 말뚝 선단부의 최대응력의 변화와 최대응력 작용 위치 또한 확인하였다. 현장 축소모형시험과 대변형 수치해석의 결과 분석을 토대로 말뚝 선단 조건의 변화를 통해 타입말뚝의 관입성을 향상 시킬 수 있으며 선단부에 집중되는 최대응력 또한 완화 시켜 말뚝 시공 중 말뚝 손상을 방지할 수 있을 것으로 결론지을 수 있었다.

Keywords

References

  1. ABAQUS CAE (2019), User's manual, Dassault Systemes Simulia, Rhode Island, USA.
  2. Current state of urban planning: Statistical information report (2022), Korea Land and Geospatial Informatix Corporation; Jeonju, Republic of Korea.
  3. Deisman, N., Flottmann, T., Guo, Y., Hodder, K.J., Chalaturnyk, R.J., and Leonardi, C. (2019), "Using 3D Printed Synthetic Rock for Systematic Evaluation of Mechanical Properties in Coal", Asian Pacific Unconventional Resources Technology Conference, November 18 - 19, Brisbane, Queensland, Australia, SPE.
  4. Determination of the optimized driving force and end time of driving for pile construction (2000), Korea Land and Housing Corporation, Jinju, Korea.
  5. Gavin, K.G. and Lahane, B.M. (2003), "The Shaft Capacity of Pipe Piles in Sand", Canadian Geotechnical Journal, Vol.40, No.1, pp.36-45. https://doi.org/10.1139/t02-093.
  6. Hodder, K.J., Nychka and Chalaturnyk, R.J. (2018), "Process Limitations of 3D Printing Model Rock", Prog. Addit. Manuf., Vol.3, No.3, pp.173-182. https://doi.org/10.1007/s40964-018-0042-6
  7. Ishutov, S., Jobe, T.D., Zhang, S., Gonzalez, M.A., Agar, S.M., Hasiuk, F., Watson, F., Geiger, S., Mackay, E., and Chalaturnyk, R. (2018), "3D Printing for Geoscience: Fundamental Research, Education, and Applications for the Petroleum Industry", American Association of Petroleum Geologists Bulletin, Vol.102.
  8. Jeong, S., Jung, H., Whittle, A., and Kim, D. (2021), "Nonlinear Analysis of Shear behavior on Pile-sand Interface Using Ring Shear Tests", Journal of Korean Geotechnical Society, Vol.37, No.5, pp.5-17. https://doi.org/10.7843/kgs.2021.37.5.5.
  9. Jeong, S. and Kim, D. (2018), "Estimation of the Load Sharing Ratio of Pre-installed Columns in Top-down Buildings on Korean Rock", KSCE Journal of Civil Engineering, Vol.22, No.12, pp. 4852-4861. https://doi.org/10.1007/s12205-017-1102-z
  10. Jeong, S., Kim, D., and Park, J. (2021), "Empirical Bearing Capacity Formula for Steel Pipe Prebored and Precast Piles based on Field Tests", ASCE International Journal of Geomechanics, Vol.21, No.9. https://doi.org/10.1061/(ASCE)GM.1943-5622.0002112.
  11. Jung, G., Kim, D., Lee, C., and Jeong, S. (2017), "Analysis of Skin Friction behavior in Prebored and Precast Piles based on Field Loading Test", Journal of Korean Geotechnical Society, Vol.33, No.1, pp.31-38. https://doi.org/10.7843/kgs.2017.33.1.31
  12. Kim, D. (2018), Proposed shaft resistance of prebored precast pile using field loading test, Doctoral dissertation, Yonsei University, Seoul, Korea.
  13. Kim, D. (2021), "Large Deformation Finite Element Analyses in TBM Tunnel Excavation: CEL and Auto-remeshing Approach", Tunnelling and Underground Space Technology, 116. https://doi.org/10.1016/j.tust.2021.104081.
  14. Kim, D. and Jeong, S. (2019), "Comparative Study of Load Distribution Ratio of Various Piled Raft Foundations based on Coupled Stiffness Matrix", Structural Design of Tall and Special Buildings, https://doi.org/10.1002/tal.1669.
  15. Kim, D., Jeong, S., and Park, J. (2020), "Analysis on Shaft Resistance of the Steel Pipe Prebored and Precast Piles based on Field Load-transfer Curves and Finite Element Method", Soils and Foundations, 60, pp.478-495. https://doi.org/10.1016/j.sandf.2020.03.011.
  16. Kim, D., Jeong, S., Jung, G., and Park, J. (2018), "Load-sharing Ratio of Prebored and Precast Pile in Top-down Method Construction Process", Structural Design of Tall and Special Buildings, https://doi.org/10.1002/tal.1472.
  17. Kim, D., Kim, J., and Jeong, S. (2019), "Estimation of Axial Stiffness on Existing and Reinforcing Piles in Vertical Extension Remodeled Buildings", Engineering Structures, https://doi.org/10.1016/J.engstruct.2019.109466.
  18. Kim, S. and Jun, Y. (1998), A Case Study on Pile Damage Assessment by Dynamic Monitoring, Korean Geotechnical Society '98 National Conference, Seoul, Korea.
  19. Ko, J. and Jeong, S. (2015), "Plugging Effect of Open-ended Piles in Sandy Soil", Canadian Geotechnical Journal, 52, pp.535-547. doi/10.1139/cgj-2014-0041.
  20. Lee, S., Kim, D., and Jeong, S. (2016), "A Study on the Excavation Damage Zone (EDZ) under Advancement based on Large Deformation Technique (Coupled Eulerian-Lagrangian", Journal of Korean Geotechnical Society, Vol.32, No.12, pp.5-13. https://doi.org/10.7843/kgs.2016.32.12.5.
  21. Moon, S. and Jo, H. (2018), "Improvement of Design Performance for the Minimization of Public Grievances based on a Construction Public Grievances Breakdown Structure", Korean Journal of Construction Engineering Management, Vol.19, No.1, pp.12-20. https://doi.org/10.6106/KJCEM.2018.19.1.012.
  22. Orazalin, Z. (2017), Analysis of Large Deformation Offshore Geotechnical Problems in Soft Clay, Ph.D thesis, Massachusetts Institute of Technology, Cambridge MA, USA.
  23. Orazalin, Z. and Whittle, A. (2018), "Realistic Numerical Simulations of Cone Penetration with Advanced Soil Models", Cone Penetration Testing 2018, Delft, June.
  24. Restriction of noise and vibration: Municipal and Provincial Report (2021), Ministry of Environment, Sejong, Korea.
  25. Santiago, V., Guerrero Zabala, F., Sanchez-Barra, A., Deisman, N., Ch alaturnyk, R., Zh ang, R., and Hurter, S. (2022), "Experimental Investigation of the Flow Properties of Layered Coal-rock Analogues", Chemical Engineering Research and Design, Vol.186, pp.685-700. https://doi.org/10.1016/j.cherd.2022.08.046
  26. Shim, Y. (2005), A Study on Damage and Quality Control of PHC Pile Construction, MSc Thesis, Chunbuk National University, Jeonju Korea.