DOI QR코드

DOI QR Code

Geometry optimization of a double-layered inertial reactive armor configured with rotating discs

  • Bekzat Ajan (Department of Mechanical and Aerospace Engineering, School of Engineering and Digital Sciences, Nazarbayev University) ;
  • Dichuan Zhang (Department of Civil and Environmental Engineering, School of Engineering and Digital Sciences, Nazarbayev University) ;
  • Christos Spitas (Department of Mechanical and Aerospace Engineering, School of Engineering and Digital Sciences, Nazarbayev University) ;
  • Elias Abou Fakhr (Department of Mechanical and Aerospace Engineering, School of Engineering and Digital Sciences, Nazarbayev University) ;
  • Dongming Wei (Department of Mathematics, School of Sciences and Humanities, Nazarbayev University)
  • 투고 : 2023.08.02
  • 심사 : 2023.09.22
  • 발행 : 2023.10.25

초록

An innovative inertial reactive armor is being developed through a multi-discipline project. Unlike the well-known explosive or non-explosive reactive armour that uses high-energy explosives or bulging effect, the proposed inertial reactive armour uses active disc elements that is set to rotate rapidly upon impact to effectively deflect and disrupt shaped charges and kinetic energy penetrators. The effectiveness of the proposed armour highly depends on the tangential velocity of the impact point on the rotating disc. However,for a single layer armour with an array of high-speed rotating discs, the tangential velocity is relatively low near the center of the disc and is not available between the gap of the discs. Therefore, it is necessary to configure the armor with double layers to increase the tangential velocity at the point of impact. This paper explores a multi-objective geometry design optimization for the double-layered armor using Nelder-Mead optimization algorithm and integration tools of the python programming language. The optimization objectives include maximizing both average tangential velocity and high tangential velocity areas and minimizing low tangential velocity area. The design parameters include the relative position (translation and rotation) of the disc element between two armor layers. The optimized design results in a significant increase of the average tangential velocity (38%), increase of the high tangential velocity area (71.3%), and decrease of the low tangential velocity area (86.2%) as comparing to the single layer armor.

키워드

과제정보

This research was funded by the Ministry of Education and Sciences, Kazakhstan under Grant No. AP09259703. The authors are grateful for this support.

참고문헌

  1. Boorla, S.M., Bjarklev, K., Eifler, T., Howard, T.J. and McMahon, C.A. (2019), "Industry 4.0-A challenge for variation simulation tools for mechanical assemblies", Adv. Comput. Des., 4, 43-52. https://doi.org/10.12989/acd.2019.4.1.043.
  2. Cohen-Arazi, Y., Sokol, E., Frilling, S. and Shaked, I. (2012), "Extremely insensitive detonating substance and method for its manufacture", United States Patent, 8277584 B2.
  3. Fras, T. (2021a), "Experimental and numerical study on a non-explosive reactive armour with the rubber Interlayer applied against kinetic-energy penetrators-the 'bulging effect' analysis", Materials, 14. https://doi.org/10.3390/ma14123334.
  4. Fras, T. (2021b), "Modelling of bulging steel-elastomer armour applied against long-rod projectiles", J. Phys., 1855 (1), 012-016. https://doi.org 10.1088/1742-6596/1855/1/012016.
  5. Flipsen, S. and Spitas, C. (2011), "Direct methanol fuel cells: A database-driven design procedure", J. Power Sources, 196, 8472-8483. https://doi.org/10.1016/j.jpowsour.2011.06.014/
  6. Gajewski, J., Golewski, P. and Sadowski, T. (2017), "Geometry optimization of a thin-walled element for an air structure using hybrid system integrating artificial neural network and finite element method", Compos. Struct., 159, 589-599. https://doi.org/10.1016/j.compstruct.2016.10.007.
  7. Giguere, P. and Selig, M. (1997), "Aerodynamic Blade Design Methods for Horizontal Axis Wind Turbines", Proceedings of the 13th Canadian Wind Energy Conference, Quebec City, Quebec, Canada.
  8. Giguere, P. and Selig, M. (2000), "Blade geometry optimization for the design of wind turbine rotors", Proceedings of the 2000 ASME Wind Energy Symposium. https://doi.org/10.2514/6.2000-45.
  9. Goetz, J., Tan, H., Renaud, J. and Tovar, A. (2012), "Two-material optimization of plate armor for blast mitigation using hybrid cellular automata", Eng. Optimiz., 985-1005. https://doi.org/10.1080/0305215X.2011.624182.
  10. Gordini, M., Habibi, M.R., Sheidaii, M.R. and Tahamouliroudsari, M. (2017), "Reliability analysis of double-layer domes with stochastic geometric imperfections", Adv. Comput. Des., 2(2), 133-146. https://doi.org/10.12989/acd.2017.2.2.133.
  11. Gov, N., Kivity, Y. and Yaziv, D. (1992) "On the interaction of a shaped charge jet with a rubber filled metallic cassette", Proceedings of the 13th International Symposium on Ballistics, 95-102.
  12. Graswald, M., Gutser, R., Breiner, J., Grabner, F., Lehmann, T. and Oelerich, A. (2019), "Defeating Modern Armor and Protection Systems", Hypervelocity Impact Symposium, 4. https://doi.org/10.1115/HVIS2019-050.
  13. Held, M. (1973), "Schutzeinrichtung gegen Geschosse, insbesondere Hohlladungsgeschosse (protection device against projectiles, especially shaped charges)", Germany Patent, 2358227.
  14. Held, M. (2005), "Defeating mechanisms of reactive armour sandwiches", Proceedings of the 22nd International Symposium on Ballistics, 1001-1007.
  15. Kaveh, A. and Bakhshpoori, T. (2016), "An efficient multi-objective cuckoo search algorithm for design optimization", Adv. Comput. Des., 1(1), 87-103. http://dx.doi.org/10.12989/acd.2016.1.1.087.
  16. Lanz, W., Odermatt, W. and Weihrauch, G. (2001), "Kinetic energy projectiles: development history, state of the art, trends", Proceedings of the 19th International Symposium on Ballistics, Interlaken, Switzerland, May, 1191-1197.
  17. Liden, E. andersson, O. and Lundberg, B. (2011), "Deformation and fracture of a long-rod projectile induced by an oblique moving plate: Experimental tests", Int. J. Impact Eng., 38, 989-1000. https://doi.org/10.1016/j.ijimpeng.2011.07.002.
  18. Liden, E. and Helte, A. (2016), "The break-up tendency of long rod projectiles", Defence Technology, 12, 177-187. https://doi.org/10.1016/j.dt.2016.01.003.
  19. Liden, E., Mousavi, S., Helte, A. and Lundberg, B. (2012), "Deformation and fracture of a long-rod projectile induced by an oblique moving plate: Numerical simulations", Int. J. Impact Eng., 40-41, 35-45. https://doi.org/10.1016/j.ijimpeng.2011.09.003.
  20. Mayseless, M. (2011), "Effectiveness of explosive reactive armor", J. Appl. Mech., 78, 051006. https://doi.org/10.1115/1.4004398.
  21. Mayseless, M., Ehrlich, Y., Falcovitz, Y.,Weihs, D. and Rosenberg, G. (1984), "Interaction of shaped-charge jets with reactive armor", Proceedings of the 8th Int. Sym. on Ballistics, Orlando, Florida.
  22. Mayseless, M., Friling, S. and Misiuk, L. (2019), "Re-visiting the mass-flux model for explosive reactive armor and the effect of plate thickness", Defence Technology, 15, 779-785. https://doi.org/10.1016/j.dt.2019.08.015.
  23. Rosenberg, Z. and Dekel, E. (1998), "A parametric study of the bulging process in passive cassettes with 2- D numerical simulations", Int. J. Impact Eng., 21, 297-305. https://doi.org/10.1016/S0734-743X(97)00082-1.
  24. Rosenberg, Z., Dekel, E., Ashuach, Y. and Yeshurun, Y. (2008), "On the main mechanisms for defeating AP projectiles, long rods and shaped charge jets", Int. J. Impact Eng., 36, 588-596. https://doi.org/10.1016/j.ijimpeng.2008.09.003.
  25. Schaal, K., Bauer, A., Chandrashekar, P., Pakmor, R., Klingenberg, C. and Springel, V. (2015), "Astrophysical hydrodynamics with a high-order discontinuous Galerkin scheme and adaptive mesh refinement", Monthly Notice. Royal Astronom. Soc., 453(4), 4279-430. https://doi.org/10.1093/mnras/stv1859.
  26. Selig, M. and Coverstone-Carroll, V. (1996), "Application of a genetic algorithm to wind turbine design", ASME J. Solar Energy Eng., 118, 22-28. https://doi.org/10.1115/1.2792688.
  27. Yaziv, D., Friling, S. and Kivity, Y. (1995), "The interaction of inert cassettes with shaped charge jets", Proceedings of the 15th International Symposium on Ballistics, 1, 461-467.