DOI QR코드

DOI QR Code

Improving support performances of cone bolts by a new grout additive and energy absorber

  • Komurlu, Eren (Department of Civil Engineering, Giresun University)
  • 투고 : 2021.03.18
  • 심사 : 2022.04.23
  • 발행 : 2022.09.25

초록

The cone bolts with expanded front ends supply improved anchoring performances and increase energy absorbing capacities due to ploughing in the grouted drills. Within this study, use of a novel energy absorber for the cone bolt heads were investigated to assess its design in terms of supplying high support performances. Additionally, different grout material designs were tested to investigate whether the energy absorption capacities of the rock bolts can be improved using a silicone based thermoset polymer (STP) additive. To determine load bearing and energy absorption capacities, a series of deformation controlled pull-out tests were carried out by using bolt samples grouted in rock blocks. According to the results obtained from this study, maximum load bearing capacities of cone bolts are similar and mostly depend on the steel material strength, whereas the energy absorption capacity was determined to significantly vary in accordance with the displacement limits of the shanks. As a result of using STP additive and new polyamide absorber rings, displacement limits without the steel failure increase. The STP additive was found to improve the energy absorption capacities of grouted cone bolts. The absorber rings designed within this study were also assessed to be highly effective and able to double up the energy absorption capacities of the cone bolts.

키워드

참고문헌

  1. Abdelbary, A. and Nasr, M.N.A. (2016), "Fatigue wear of polyamides with surface defects under different loading conditions", Adv. Mater. Res., Int. J., 5(3), 193-203. http://dx.doi.org/10.12989/amr.2016.5.3.193
  2. Aksoy, C.O., Ogul, K., Topal, I., Ozer, S.C., Ozacar, V., Posluk, E. (2012), "Numerical modeling of nondeformable support in swelling and squeezing rock", Int. J. Rock. Mech. Min. Sci., 52, 61-70. https://doi.org/10.1016/j.ijrmms.2012.02.008
  3. ASTM (2020), ASTM C143/C143M-20: Standard Test Method for Slump of Hydraulic-Cement Concrete. ASTM International, West Conshohocken, PA, USA.
  4. Barla, G. (2016), "Full-face excavation of large tunnels in difficult conditions", J. Rock Mech. Geotech. Eng., 8(3), 294-303. https://doi.org/10.1016/j.jrmge.2015.12.003
  5. Cai, M. (2019), "Rock support in strainburst-prone ground", Int. J. Min. Sci. Technol., 29, 529-534. https://doi.org/10.1016/j.ijmst.2019.06.008
  6. Carmona, S., Molins, C. and Garcia, S. (2020), "Application of Barcelona test for controlling energy absorption capacity of FRS in underground mining works", Constr. Build. Mater., 246, 118458. https://doi.org/10.1016/j.conbuildmat.2020.118458
  7. Galimzyanova, R.Y., Lisanevich, M.S. and Khakimullin, Y.N. (2020), "Sealing materials based on polymers", Key Eng. Mater., 869, 93-100. https://doi.org/10.4028/www.scientific.net/kem.869.93
  8. Hao, Y., Wu, Y., Ranjith, P.G., Zhang, K., Hao, G. and Teng, Y. (2020), "A novel energy-absorbing rock bolt with high constant working resistance and long elongation: Principle and static pull-out test", Constr. Build. Mater., 243, 118231. https://doi.org/10.1016/j.conbuildmat.2020.118231
  9. Jager, A.J. (1992), "Two new support units for the control of rockburst damage", In: Proceedings of International Symposium on Rock Support in Mining and Underground Construction, A.A. Balkema, Rotterdam, The Netherlands, pp. 621-631.
  10. Jiang, B., Oh, K.H., Kim, S.Y., He, X. and Oh, S.K. (2019), "Technical evaluation method for physical property changes due to environmental degradation of grout-injection repair materials for water-leakage cracks", Appl. Sci., 9(9), 1740. https://doi.org/10.3390/app9091740
  11. Kabwe, E. and Wang, Y. (2015), "Review on rockburst theory and types of rock support in rockburst prone mines", Open J. Saf. Sci. Technol., 5(4), 104-121. http://dx.doi.org/10.4236/ojsst.2015.54013
  12. Kim, H.J., Kim, K.H., Kim, H.M. and Shin, J.H. (2018), "Anchorage mechanism and pullout resistance of rock bolt in water-bearing rocks", Geomech. Eng., Int. J., 15(3), 841-849. http://dx.doi.org/10.12989/gae.2018.15.3.841
  13. Kim, H., Rehman, H., Ali, W., Naji, A.M., Kim, J.J., Kim, J. and Yoo, H. (2019), "Classification of factors affecting the performance of fully grouted rock bolts with empirical classification systems", Appl. Sci., 9, 4781. http://dx.doi.org/10.3390/app9224781
  14. Komurlu, E. (2020), "An Investigation of Using Thermoset Polymer type Liquid Additives to Improve Cement Grout Performances in Rock Bolting Applications", Int. J. Geosynth. Ground Eng., 6, 52. https://doi.org/10.1007/s40891-020-00236-9
  15. Komurlu, E. and Kesimal, A. (2017), "Experimental study on usability of friction rockbolts with plastic bodies", Int. J. Geomech., 17(9), 04017058. https://doi.org/10.1061/(ASCE)GM.1943-5622.0000960
  16. Komurlu, E., Kesimal, A. and Aksoy, C.O. (2017), "Use of polyamide-6 type engineering polymer as grouted rock bolt material", Int. J. Geosynth. Ground Eng., 3, 37. https://doi.org/10.1007/s40891-017-0114-6
  17. Komurlu, E., Demir, A.D. and Celik, A.G. (2020), "Investigation of load bearing capacities of grouted rock bolts with new auxetic head designs", Period Polytech. Civil Eng., 64(3), 782-791. https://doi.org/10.3311/PPci.16366
  18. Korzeniowski, W., Skrzypkowski, K. and Zagorski, K. (2017), "Reinforcement of underground excavation with expansion shell rock bolt equipped with deformable component", Studia Geotechnica et Mechanica, 39, 39-52. https://doi.org/10.1515/sgem-2017-0004
  19. Li. C.C. (2007), "A Practical problem with threaded rebar bolts in reinforcing largely deformed rock mass", Rock Mech. Rock Eng., 40(5), 519-524. https://doi.org/10.1007/s00603-006-0094-7
  20. Li, C.C. (2017), "Principles of rockbolting design", J. Rock Mech. Geotech. Eng., 9(3), 396-414. https://doi.org/10.1016/j.jrmge.2017.04.002
  21. Li, C.C., Stjern, G. and Myrvang, A. (2014), "A review on the performance of conventional and energyabsorbing rockbolts", J. Rock Mech. Geotech. Eng., 6(4), 315-327. https://doi.org/10.1016/j.jrmge.2013.12.008
  22. Li, C.C., Kristjansson, G. and Hoien, A.H. (2016a), "Critical embedment length and bond strength of fully encapsulated rebar rockbolts", Tunnel. Und. Space Tech., 59, 16-23. http://dx.doi.org/10.1016/j.tust.2016.06.007
  23. Li, C., Wu, J., Wang, J., Li, X. (2016b), "Layout and length optimization of anchor cables for reinforcing rock wedges", Bull. Eng. Geol. Environ., 75, 1399-1412. https://doi.org/10.1007/s10064-015-0756-3
  24. Liang, Y., He, M., Cao, C., Wang, S. and Ren, T. (2017), "A mechanical model for conebolts", Comput. Geotech., 83, 142-151. https://doi.org/10.1016/j.compgeo.2016.10.017
  25. Liu, H., Yu, B., Liu, J. and Wang, T. (2019), "Investigation of impact rock burst induced by energy released from hard rock fractures", Arab. J. Geosci., 12, 381. https://doi.org/10.1007/s12517-019-4536-4
  26. Magalhaes, S., Alves, L., Medronho, B., Fonseca. A.C., Romano, A., Coelho, J.F.J. and Norgren, M. (2019), "Brief overview on bio-based adhesives and sealants", Polymers, 11(10), 1685. https://doi.org/10.3390/polym11101685
  27. Obeid, H., Clement, A., Freour, S., Jacquemin, F. and Casari, P. (2018), "On the identification of the coefficient of moisture expansion of polyamide-6: Accounting differential swelling strains and plasticization", Mech. Mater., 118, 1-10. https://doi.org/10.1016/j.mechmat.2017.12.002
  28. Oge, I.F. (2021), "Revisiting the assessment of squeezing condition and energy absorption of flexible supports: A mine development case", Tunnel. Und. Space Tech., 108, 103712. https://doi.org/10.1016/j.tust.2020.103712
  29. Owen, M.J. (2017), "Silicone hydrophobicity and oleophilicity", Silicon, 9, 651-655. https://doi.org/10.1007/s12633-014-9188-0
  30. Ranjbarnia, M., Fahimifar, A. and Oreste, P. (2016), "Practical method for the design of pretensioned fully grouted rockbolts in tunnels", Int. J. Geomech., 16(1), 04015012. https://doi.org/10.1061/(ASCE)GM.1943-5622.0000464
  31. Skrzypkowski, K., Korzeniowski, W., Zagorski, K. and Zagorska, A. (2020a), "Modified rock bolt support for mining method with controlled roof bending", Energies, 13, 1868. https://doi.org/10.3390/en13081868
  32. Skrzypkowski, K., Korzeniowski, W., Zagorski, K. and Zagorska, A. (2020b), "Adjustment of the yielding system of mechanical rock bolts for room and pillar mining method in stratified rock mass", Energies, 13, 2082. https://doi.org/10.3390/en13082082
  33. Stacey, T.R. (2016), "Addressing the consequences of dynamic rock failure in underground excavations", Rock Mech. Rock Eng., 49(10), 4091-4101. https://doi.org/10.1007/s00603-016-0922-3
  34. Teymen, A. (2017), "Effect of mineral admixture types on the grout strength of fully-grouted rockbolts", Constr. Build. Mater., 145, 376-382. https://doi.org/10.1016/j.conbuildmat.2017.04.046
  35. Uyar, G.G. and Aksoy, C.O. (2018), "New support suggestions to high swelling clayey rock mass", J. Min. Sci., 54(4), 617-627. https://doi.org/10.1134/S1062739118044087
  36. Wang, H., Li, S., Wang, Q., Wang, D., Li, W., Liu, P., Li, X. and Chen, Y. (2019), "Investigating the supporting effect of rock bolts in varying anchoring methods in a tunnel", Geomech. Eng., Int. J., 19(6), 485-498. http://dx.doi.org/10.12989/gae.2019.19.6.485
  37. Wang, B., He, M. and Qiao, Y. (2021), "Resistance behavior of Constant-Resistance-Large-Deformation bolt considering surrounding rock pressure", Int. J. Rock. Mech. Min. Sci., 137, 104511. https://doi.org/10.1016/j.ijrmms.2020.104511
  38. Wang, Y., Xiang, X., Li, C., Zhu, G., Song, C., Xian, J. and Zhang, J. (2022), "Load transfer laws of tensile anchors in rock masses with weak interlayers based on a shear-slipping updating model", J. Mount. Sci., 19, 812-825. https://doi.org/10.1007/s11629-021-6931-z
  39. Yang, S.Q., Chen, M., Jing, H.W., Chen, K.F. and Meng, B. (2017), "A case study on large deformation failure mechanism of deep soft rock roadway in Xin'An coal mine, China", Eng. Geol., 217, 89-101. http://dx.doi.org/10.1016/j.enggeo.2016.12.012
  40. Yokota, Y., Zhao, Z., Nie, W., Date, K., Iwano, K., Koizumi, Y. and Okada, Y. (2020), "Development of a new deformation-controlled rock bolt: Numerical modelling and laboratory verification", Tunnel. Undergr. Space Tech., 98, 103305. https://doi.org/10.1016/j.tust.2020.103305
  41. Zander, L. and Peng, J. (2018), "New silane-terminated polymers for sealants and adhesives", Adhes. Adhes. Sealants, 15, 20-23. https://doi.org/10.1007/s35784-018-0014-8
  42. Zhang, C., Cui, G., Chen, X., Zhou, H. and Deng, L. (2020a), "Effects of bolt profile and grout mixture on shearing behaviors of bolt-grout interface", J. Rock Mech. Geotech. Eng., 12, 242-255. https://doi.org/10.1016/j.jrmge.2019.10.004
  43. Zhang, W., Huang, L. and Juang, C.H. (2020b), "An analytical model for estimating the force and displacement of fully grouted rock bolts", Comput. Geotech., 117, 103222. https://doi.org/10.1016/j.compgeo.2019.103222
  44. Zhang, W., Song, Y., Huang, L. and Gong, S. (2022), "Analytical relations for the mechanical properties of full-length bonded rock bolts when subjected to freeze-thaw processes", Comput. Geotech., 145, 104667. https://doi.org/10.1016/j.compgeo.2022.104667