DOI QR코드

DOI QR Code

Technology to reduce water ingress for TBM cutterhead intervention

  • Ham, Soo-Kwon (Department of Civil and Environmental Engineering, Konkuk University) ;
  • kim, Beom-Ju (Department of Civil and Environmental Engineering, Konkuk University) ;
  • Lee, Seok-Won (Department of Civil and Environmental Engineering, Konkuk University)
  • 투고 : 2021.12.15
  • 심사 : 2022.03.15
  • 발행 : 2022.05.10

초록

Tunnel site where high water pressure is applied, such as subsea tunnel, generally selects the shield TBM (Tunnel Boring Machine) to maintain the tunnel excavation face. The shield TBM has cutters installed, and the cutters wear out during the process of excavation, so it should be checked and replaced regularly. This is called CHI (Cutterhead Intervention). The conventional CHI under high water pressure is very disadvantageous in terms of safety and economics because humans perform work in response to high water pressure and huge water inflow in the chamber. To overcome this disadvantage, this study proposes a new method to dramatically reduce water pressure and water ingress by injecting an appropriate grout solution into the front of the tunnel face through the shield TBM chamber, called New Face Grouting Method (NFGM). The tunnel model tests were performed to determine the characteristics, injection volume, and curing time of grout solution to be applied to the NFGM. Model test apparatus was composed of a pressure soil tank, a model shield TBM, a grout tank, and an air compressor to measure the amount of water inflow into the chamber. The model tests were conducted by changing the injection amount of the grout solution, the curing time after the grout injection, and the water/cement ratio of grout solution. From an economic point of view, the results showed that the injection volume of 1.0 L, curing time of 6 hours, and water/cement ratio of the grout solution between 1.5 and 2.0 are the most economical. It can be concluded that this study has presented a method to economically perform the CHI under the high water pressure.

키워드

과제정보

This work was supported by the National Research Foundation of Korea (NRF) grant funded by the Korea government (MSIT). (No. 2019R1A2C100611013).

참고문헌

  1. Ahn, C.K., Yu, J.S. and Lee, S.W. (2018), "Evaluation of the backfill injection pressure and its effect on ground settlement for shield TBM using numerical analysis", J. Korean Tunn. Undergr. Sp. Assoc., 20(2), 269-286. https://doi.org/10.9711/KTAJ.2018.20.2.269.
  2. Anagnostou, G. (1995), "The influence of tunnel excavation on the hydraulic head", J. Numer. Anal. Meth. Geomech., 19(10), 725-746. https://doi.org/10.1002/nag.1610191005.
  3. Au, S.K.A., Soga, K., Jafari, M.R., Bolton, M.D. and Komiya, K. (2003), "Factors affecting longterm efficiency of compensation grouting in clays", J. Geotech. Geoenviron. Eng., 129(3), 254-262. https://doi.org/10.1061/(ASCE)1090-0241(2003)129:3(254).
  4. Bezuijen, A., Talmon, A.M., Kaalberg, F.J. and Plugge, R. (2004), "Field measurements of grout pressures during tunnelling of the Sophia Rail Tunnel", Soil. Found., 44(1), 39-48. https://doi.org/10.3208/sandf.44.39.
  5. Brian F., Michael B. and Knut G. (2008), "Pre-excavation drilling and grouting for water control and ground improvement in highly variable ground conditions at the Arrowhead Tunnels Project", Proceedings of North American Tunneling, Society for Mining, Metallurgy & Exploration, San Francisco, USA.
  6. Celik, F. (2019), "The observation of permeation grouting method as soil improvement technique with different grout flow models", Geomech. Eng., 17(4), 367-374. https://doi.org/10.12989/gae.2019.17.4.367.
  7. Chan, A.W.Y., Yeung, C.H.C., Westmoreland, A.J., Fok, S.W., Ng, C.C.W. and Guedon F. (2021), "Use of saturation diving technique for tunnel boring machine cutterhead intervention in the Tuen Mun-Chek Lap Kok Link Sub-sea Tunnel Project, Hong Kong", HKIE Transactions, 28(1), 31-38. https://doi.org/10.33430/V28N1THIE-2019-0044.
  8. Dias, T. and Bezuijen, A. (2017), "Grout pressure distribution during TBM tunnelling", Geotechnical Aspects of Underground Construction in Soft Ground, 9th International Symposium (ISSao Paulo), Brazil.
  9. Duhme, R. and Tatzki T. (2015), "Designing TBMs for subsea tunnels", J Korean Tunn. Undergr. Sp. Assoc., 17(6), 587-596. https://doi.org/10.9711/KTAJ.2015.17.6.587.
  10. Farrokh, E. and Kim, D.Y. (2018), "A discussion on hard rock TBM cutter wear and cutterhead intervention interval length evaluation", Tunn. Undergr. Sp. Tech., 81, 336-357. https://doi.org/10.1016/j.tust.2018.07.017.
  11. Jeon, Y.J., Jeon, S.C., Jeon, S.J. and Lee, C.J. (2020), "Study on the behaviour of pre-existing single piles to adjacent shield tunnelling by considering the changes in the tunnel face pressures and the locations of the pile tips", Geomech. Eng., 21(2), 187-200. https://doi.org/10.12989/gae.2020.21.2.187.
  12. Jin, Y., Han, L., Meng, Q. Meng, Ma, D., Wen, S. and Wang, S. (2018), "Experimental investigation of the mechanical behaviors of grouted crushed coal rocks under uniaxial compression", Geomech. Eng., 16(3), 273-284. https://doi.org/10.12989/gae.2018.16.3.273.
  13. Kasper, T. and Meschke, G. (2006), "On the influence of face pressure, grouting pressure and TBM design in soft ground tunneling", Tunn. Undergr. Sp. Tech., 21(2), 160-171. https://doi.org/10.1016/j.tust.2005.06.006.
  14. Kim, K.S., Oh, J.Y., Lee, H.B., Kim, D.K. and Choi, H.S. (2018), "Critical face pressure and backfill pressure in shield TBM tunneling on soft ground", Geomech. Eng., 15(3), 823-831. https://doi.org/10.12989/gae.2018.15.3.823.
  15. Kim, Y.S. and Moon J.S. (2020), "Change of groundwater inflow by cutoff grouting thickness and permeability coefficient", Geomech. Eng., 21(2), 165-170. https://doi.org/10.12989/gae.2020.21.2.165.
  16. Kindwall E.P. (1990), "A short history of diving and diving medicine", (Eds., Bove, A.A. and Jefferson, C.D.) Diving medicine (2nd Ed.), WB Saunders Company.
  17. Lee, G.T.K. and Ng, C.W.W. (2005), "The effects of advancing open face tunnelling on an existing loaded pile", J. Geotech. Geoenviron. Eng., 131(2), 193-201. https://doi.org/10.1061/(ASCE)1090-0241(2005)131:2(193).
  18. Lee, H.B., Oh, T.M. and Lee, J.W. (2021), "Evaluation of grout penetration in single rock fracture using electrical resistivity", Geomech. Eng., 24(1), 1-14, https://doi.org/10.12989/gae.2021.24.1.001.
  19. Masini, L., Rampello, S. and Soga, K. (2014), "An approach to evaluate the efficiency of compensation grouting", J. Geotech. Geoenviron. Eng., 140(12), 04014073-1 - 04014073-12. https://doi.org/10.1061/(ASCE)GT.1943-5606.0001180.
  20. Rezaei A.H., Shirzehhagh, M. and Golpasand, M.R.B. (2019), "EPB tunneling in cohesionless soils: A study on Tabriz Metro settlements", Geomech. Eng., 19(2), 153-165. https://doi.org/10.12989/gae.2019.19.2.153.
  21. The International Tunnelling Association Working Group (2018), "Guidelines for Good Working Practice in High Pressure Compressed Air", 5(3).
  22. Yoon, Y.M., Jeong, H.Y. and Jeon, S.W. (2018), "Review of pre-grouting methods for shield TBM tunneling in difficult grounds", Tunn. Undergr. Sp., 28(6), 528-546. https://doi.org/10.7474/TUS.2018.28.6.528.