DOI QR코드

DOI QR Code

An analytical approach for aeroelastic analysis of tail flutter

  • 투고 : 2021.09.02
  • 심사 : 2021.11.08
  • 발행 : 2022.01.25

초록

In this research, the aeroelastic instability of a tail section manufactured from aluminum isotropic material with different shell thickness investigated. For this purpose, the two degrees of freedom flutter analytical approach are used, which is accompanied with simulation by finite element analysis. Using finite element analysis, the geometry parameters such as the center of mass, the aerodynamic center and the shear center are determined. Also, by simulation of finite element method, the bending and torsional stiffnesses for various thickness of the airfoil section are determined. Furthermore, using Lagrange's methods the equations of motion are derived and modal frequency and critical torsional/bending modes are discussed. The results show that with increasing the thickness of the isotropic airfoil section, the flutter and divergence speeds increased. Compared of the obtained results with other research, indicates a good agreement and reliability of this method.

키워드

참고문헌

  1. Aleksandrowicz, R. and Lucjanek, W. (1958), "Sailplane stiffness measurements", OSTIV Publications, 5.
  2. Borri, C. and Costa, C. (2004), "A parametric study of indicial function models in bridge deck aeroelasticity", Wind Struct., 7(6), 405-420. http://dx.doi.org/10.12989/was.2004.7.6.405.
  3. Budiansky, B., Kotanchik, J.N. and Chiarito, P.T. (1947), A Torsional Stiffness Criterion for Preventing Flutter of Wings of Supersonic Missiles, National Advisory Committee for Aeronautics Langley Field Va Langley Aeronautical Laboratory.
  4. Cai, J., Zhang, Q., Jiang, Y., Xu, Y., Feng, J. and Deng, X. (2017), "Nonlinear stability analysis of a radially retractable hybrid grid shell in the closed position", Steel Compos. Struct., 24(3), 287-296. https://doi.org/10.12989/scs.2017.24.3.287.
  5. Diana, G., Resta, F., Zasso, A., Belloli, M. and Rocchi, D. (2004), "Effects of the yaw angle on the aerodynamic behaviour of the Messina multi-box girder deck section", Wind Struct., 7(1), 41-54. http://dx.doi.org/10.12989/was.2004.7.1.041.
  6. Dillinger, J.K.S., Klimmek, T., Abdalla, M.M. and Gurdal, Z. (2013), "Stiffness optimization of composite wings with aeroelastic constraints", J. Aircraft, 50(4), 1159-1168. https://doi.org/10.2514/1.C032084.
  7. Ding, Q., Chen, A. and Xiang, H. (2002), "A state space method for coupled flutter analysis of long-span bridges", Struct. Eng. Mech., 14(4), 491-504. http://dx.doi.org/10.12989/sem.2002.14.4.491.
  8. Eltaher, M.A. and Mohamed, S.A. (2020), "Buckling and stability analysis of sandwich beams subjected to varying axial loads", Steel Compos. Struct., 34(2), 241-260. https://doi.org/10.12989/scs.2020.34.2.241.
  9. Evans, S.P., Bradney, D.R. and Clausen, P.D. (2018), "Development and experimental verification of a 5kW small wind turbine aeroelastic model", J. Wind Eng. Ind. Aerod., 181, 104-111. https://doi.org/10.1016/j.jweia.2018.08.011.
  10. Ghasemi, A.R., Jahanshir, A. and Tarighat, M.H. (2014), "Numerical and analytical study of aeroelastic characteristics of wind turbine composite blades", Wind Struct., 18(2), 103-116. http://dx.doi.org/10.12989/was.2014.18.2.103.
  11. Ghasemi, A.R. and Mohandes, M. (2016), "Composite blades of wind turbine: Design, stress analysis, aeroelasticity, and fatigue", Wind Turb. Des. Control Appl., 1-26. http://dx.doi.org/10.5772/63446.
  12. Grinderslev, C., Lubek, M. and Zhang, Z. (2018), "Nonlinear fluid-structure interaction of bridge deck: CFD analysis and semi-analytical modeling", Wind Struct., 27(6), 381-397. http://dx.doi.org/10.12989/was.2018.27.6.381.
  13. Hodges, D.H. and Pierce, G.A. (2011), Introduction to Structural Dynamics and Aeroelasticity (Vol. 15). Cambridge university press.
  14. Kumar, S., Onkar, A.K. and Manjuprasad, M. (2020), "Stochastic modeling and reliability analysis of wing flutter. journal of aerospace engineering", 33(5), 04020044. https://doi.org/10.1061/(ASCE)AS.1943-5525.0001153.
  15. Lair, J., Hui, D., Sofiyev, A.H., Gribniak, V. and Turan, F. (2019), "On the parametric instability of multilayered conical shells using the FOSDT", Steel Compos. Struct., 31(3), 277-290. https://doi.org/10.12989/scs.2019.31.3.277.
  16. Li, Z., Wen, B., Dong, X., Peng, Z., Qu, Y. and Zhang, W. (2020), "Aerodynamic and aeroelastic characteristics of flexible wind turbine blades under periodic unsteady inflows", J. Wind Eng. Ind. Aerod., 197, 104057. https://doi.org/10.1016/j.jweia.2019.104057.
  17. Mahmoud, S.R. and Tounsi, A. (2019), "On the stability of isotropic and composite thick plates", Steel Compos. Struct., 33(4), 551-568. https://doi.org/10.12989/scs.2019.33.4.551.
  18. Marzani, A. and Viola, E. (2003), "Effect of boundary conditions on the stability of beams under conservative and non-conservative forces", Struct. Eng. Mech., 16(2), 195-217. http://dx.doi.org/10.12989/sem.2003.16.2.195.
  19. Mastroddi, F., Tozzi, M. and Capannolo, V. (2011), "On the use of geometry design variables in the MDO analysis of wing structures with aeroelastic constraints on stability and response", Aerosp. Sci. Technol., 15(3), 196-206. https://doi.org/10.1016/j.ast.2010.11.003.
  20. Mousavi, S.B. and Yazdi, A.A. (2019), "Aeroelastic behavior of nano-composite beam-plates with double delaminations", Steel Compos. Struct., 33(5), 653-661. http://dx.doi.org/10.12989/scs.2019.33.5.653.
  21. Omenzetter, P., Wilde, K. and Fujino, Y. (2000), "Suppression of wind-induced instabilities of a long span bridge by a passive deck-flaps control system: Part I: formulation", J. Wind Eng. Ind. Aerod., 87(1), 61-79. https://doi.org/10.1016/S0167-6105(00)00016-7
  22. Shafei, E. and Shirzad, A. (2017), "Ant colony optimization for dynamic stability of laminated composite plates", Steel Compos. Struct., 25(1), 105-116. https://doi.org/10.12989/scs.2017.25.1.105.
  23. Stodieck, O., Cooper, J.E., Weaver, P.M. and Kealy, P. (2017), "Aeroelastic tailoring of a representative wing box using tow-steered composites", AIAA J., 55(4), 1425-1439. https://doi.org/10.2514/1.J055364.
  24. Taheri-Behrooz, F. and Omidi, M. (2018), "Buckling of axially compressed composite cylinders with geometric imperfections", Steel Compos. Struct., 29(4), 557-567. https://doi.org/10.12989/scs.2018.29.4.557.
  25. Wang, Q. (2003), "On complex flutter and buckling analysis of a beam structure subjected to static follower force", Struct Eng. Mech., 16(5), 533-556. http://dx.doi.org/10.12989/sem.2003.16.5.533.