DOI QR코드

DOI QR Code

An Experimental Study on Internal Drag Correction of High Speed Vehicle Using Three Probes

세 가지 프로브를 이용한 초고속 비행체 내부 항력 보정 기법의 실험적 연구

  • Received : 2021.04.16
  • Accepted : 2021.06.24
  • Published : 2021.07.01

Abstract

Wind tunnel tests were carried out with a scramjet high speed vehicle. Since the scramjet engine does not have a compressor, it has a simple structure, but it is important to design the intake for the supersonic combustion in the combustion chamber. In this study, internal flow characteristics and the starting condition were analyzed by measuring the pressure at the isolator exit just before the combustion chamber, and the intake performance parameters were calculated and compared the result on every Mach number. The aerodynamic characteristics of the flow-through high speed vehicle were analyzed and internal drag correction is required to precisely analyze the aerodynamic characteristics. In this paper, an experimental technique using three probes for internal drag correction was proposed. By applying internal drag correction, it was able to figure out the effect of the internal flow on the aerodynamic force of the vehicle.

스크램제트 엔진을 갖는 초고속 비행체로 풍동실험을 수행하였다. 스크램제트 엔진은 별도의 압축기가 없기 때문에 간단한 구조를 갖고 있지만 연소실에서 초음속 연소가 일어날 수 있도록 흡입구를 설계하는 것이 중요하다. 본 연구에서는 연소실 직전에 있는 격리부 출구면 압력 측정을 통해 내부 유동 특성 및 흡입구 시동 조건을 판단하였고 흡입구 성능 변수를 계산하여 마하수 별로 결과를 비교하였다. 유동관통형 초고속 비행체의 공력 특성도 분석하였고 정확한 공력 특성 분석을 위해서 내부 항력 보정이 필요하다. 본 연구에서는 내부 항력 보정을 위해 세 가지 프로브를 이용한 실험 기법을 제시하였다. 내부 항력 보정을 적용하여 내부 유동이 비행체 공력에 미치는 영향을 파악할 수 있었다.

Keywords

References

  1. Fry, R. S., "A century of Ramjet Propulsion Technology Evolution," Journal of Propulsion and Power, Vol. 20, No. 1, 2004, pp. 27~58. https://doi.org/10.2514/1.9178
  2. Marimon, M. M., "Study of an air-breathing engine for hypersonic flight," 2013.
  3. Moses, P. L., Rausch, V. L., Nguyen, L. T. and Hill, J. R., "NASA hypersonic flight demonstrators-overview, status, and future plans," Acta astrounautica, Vol. 55, Issues 3-9, 2004, pp. 619~630. https://doi.org/10.1016/j.actaastro.2004.05.045
  4. Won, S. H., Jeung, I. S. and Choi, J. Y., "Overview on Hypersonic Scramjet Engine Developments," Journal of Korean Society of Propulsion Engineers, Vol. 9, No. 1, 2005, pp. 67~83.
  5. Haberle, J. and Gulhan, A., "Investigation of the Performance of a Scramjet Inlet at Mach 6 with Bopundary Layer Bleed," AIAA 2006-8139, 14th AIAA Space Planes and Hypersonic Systems and Technologies Conference, 2006.
  6. Walker, J. J., "Internal Drag Coefficient Correction," General Dynamics Corporation Fort Worth Division, 1980, pp. 1~7.
  7. Kim, J. M. and Lee, Y. B., "A Study on Effective Correction of Internal Drag and Wall Interference Using Response Surface in Wind Tunnel Test," Journal of the Korea Institute of Military Science and Technology, Vol. 22, No. 5, 2019, pp. 637~643. https://doi.org/10.9766/KIMST.2019.22.5.637
  8. Kim, S. H., Kim, Y. J., Lee, J. G. and Kim, N. G., "Introduction of ADD Hypersonic Wind Tunnels," Proceeding of The Korean Society for Aeronautical and Space Sciences Spring Conference, November 2017, pp. 23~25.
  9. AIAA Standard, "Assessment of Experimental Uncertainty with Application to Wind Tunnel Testing," AIAA S-071A-1999, 1999.
  10. Bobbitt, P. J., Maglieri. D. J., Banks, D. W. and Fuchs, A. W., "Wedge and Conical Probes for the Instantaneous Measurement of Free-Stream Flow Quantities at Supersonic Speeds," AIAA-2011-3501, 29th AiAA Applied Aerodynamics Conference, Honolulu, Hawaii, 27-30, June 2011.
  11. Haberle, J. and Gulhan, A., "Exprimental Investigation of a Two-Dimensional and a Three Dimensional Scramjet Inlet at Mach 7," Journal of Propulsion and Power, Vol. 24, No. 5, SeptemberOctober, 2008, pp. 1023~1034. https://doi.org/10.2514/1.33546
  12. Lassaline, J. V., "Supersonic Right Circular Cone at Zero Angle of Attack," High-Speed Aerodynamics, Ryerson University, March, 2009, pp. 1~3.
  13. Herrmann, C. D. and Koschel, W. W., "Exprimental Investigation of the Internal Compression of a Hypersonic Intake," AIAA-2002-4130, 38th AIAA/ASME/SAE/ASEE Joint Propulsion Conference and Exhibit, 7-10, July, 2002.