DOI QR코드

DOI QR Code

Analytical calculation method for the axial equivalent elastic modulus of laminated FRP pipes based on three-dimensional stress state

  • Chen, Li (School of Architecture Engineering, Nanjing Institute of Technology) ;
  • Pan, Darong (School of Architecture Engineering, Nanjing Institute of Technology) ;
  • Zhao, Qilin (School of Mechanical and Power Engineering, Nanjing Tech University) ;
  • Chen, Li (Engineering Research Center of Safety and Protection of Explosion & Impact of Ministry of Education, Southeast University) ;
  • Chen, Liang (College of Field Engineering, Army Engineering University of PLA) ;
  • Xu, Wei (Anhui Transport Consulting & Design Institute Co., Ltd)
  • 투고 : 2020.07.29
  • 심사 : 2020.10.04
  • 발행 : 2021.01.10

초록

In engineering design, the axial equivalent elastic modulus of laminated FRP pipe was mostly calculated by the average elastic modulus method or the classical laminated plate theory method, which are based on relatively simplified assumptions, and may be not accurate enough sometimes. A new analytical calculation method for the axial equivalent elastic modulus of laminated FRP pipe was established based on three-dimensional stress state. By comparing the results calculated by this method with those by the above two traditional analytical methods and the finite element method, it is found that this method for the axial equivalent elastic modulus fits well not only for thin-walled pipes with orthotropic layers, but also for thick-walled pipes with arbitrary layers. Besides, the influence of the layer stacking on the axial equivalent elastic modulus was studied with this method. It is found that a proper content of circumferential layer is beneficial for improving the axial equivalent elastic modulus of the laminated FRP pipe with oblique layers, and then can reduce its material quantity under the premise that its axial stiffness remains unchanged. Finally, the meso-mechanical mechanism of this effect was analyzed. The improving effect of circumferential layer on the axial equivalent elastic modulus of the laminated FRP pipe with oblique layers is mainly because that, the circumferential fibers can restrain the rigid body rotations of the oblique fibers, which tend to cause the significant deformations of the pipe wall units and the relatively low axial equivalent elastic modulus of the pipe.

키워드

과제정보

Supports from Natural Science Foundation of China (51978166), and Construction System Science and Technology Guidance Project of Jiangsu (2017ZD131, 2017ZD132, 2018ZD182) are gratefully acknowledged.

참고문헌

  1. Bai, Y. and Yang, X. (2013), "Novel joint for assembly of all-composite space truss structures: Conceptual design and preliminary study", J. Compos. Construct., 17(1), 130-138. http://doi.org/10.1061/(ASCE)CC.1943-5614.0000304.
  2. Bois, C., Pilato, A., Wahl, J.C. and Perry, N. (2013), "Proposal for a smart pressurised ring test to study thick composite produced by lament winding", Compos. Part B Eng., 53(10), 382-390. http://doi.org/10.1016/j.compositesb.2013.06.001.
  3. Chen, L., Zhao, Q. and Jiang, K. (2011), "Experimental and theoretical research on the compression performance of CFRP sheet confined GFRP short pole", Struct. Eng. Mech., 40, 215-231. http://doi.org/10.12989/sem.2011.40.2.215.
  4. Darwin, D., Dolan, C.W. and Nilson, A.H. (2016), Design of Concrete Structures, McGraw Hill Education, New York, NY, USA.
  5. Deo, R., Benner, H., Vincent, D., Olason, E. and Harrison, R. (2010), "Design and Manufacture of Structurally Efficient Tapered Struts (SETS)", CR-2010-216699; NASA, USA.
  6. Editorial-Committee (2002), China Aeronautical Materials Handbook: Volume 6 (Composite and Adhesive), China Standard Press, Beijing, China.
  7. El-Sheikh, A. (1998), "Design of space truss structures", Struct. Eng. Mech., 6(2), 185-200. http://doi.org/10.12989/sem.1998.6.2.185.
  8. Feng, P., Hu, L., Qian, P. and Ye, L. (2016), "Compressive bearing capacity of CFRP-aluminum alloy hybrid tubes", Compos. Struct., 140, 749-757. http://doi.org/10.1016/j.compstruct.2016.01.041.
  9. Goodman, J.W. and Gliksman, J.A. (1969), Structural Evaluation of Long Boron Composite Columns, ASTM International, West Conshohocken, PA, USA.
  10. Hewson, P. (1978), "Buckling of pultruded glass fibre-reinforced channel sections", Compos., 9(1), 56-60. http://doi.org/10.1016/0010-4361(78)90520-7.
  11. HYER, M.W. (2009), Stress Analysis of Fiber-Reinforced Composite Materials, Destech Publications, Lancaster, Pennsylvania, USA.
  12. Jegley, D.C., Wu, K.C., Phelps, J.E., Mckenney, M.J. and Oremon, L. (2011), "Structural efficiency of composite struts for aerospace applications", J. Spacecraft Rockets, 49(5), 915-924. http://doi.org/10.2514/1.60053.
  13. Kassapoglou, C. (2010), Review of Classical Laminated Plate Theory, John Wiley and Sons, Ltd., Chichester, West Sussex, United Kingdom.
  14. Kaveh, A. and Bijari, S. (2018), "Simultaneous analysis, design and optimization of trusses via force method", Struct. Eng. Mech., 65(3), 233-241. http://doi.org/10.12989/sem.2018.65.3.233.
  15. Li, F., Zhao, Q., Chen, L. and Shao, G. (2014), "Experimental and Theoretical Research on the Compression Performance of CFRP Sheet Confined GFRP Short Pipe", The Scientific World Journal, 2014, 109692. http://doi.org/10.1155/2014/109692.
  16. Lim, T.C. (2001), "An integrated mechanics-of-materials model for the elastic stiffness of composites", Adv. Compos. Lett., 10(2), 53-59. http://doi.org/10.1177/096369350101000201.
  17. Madenci, E. (2019), "A refined functional and mixed formulation to static analyses of FGM beams", Struct. Eng. Mech., 69(4), 427-437. http://doi.org/10.12989/sem.2019.69.4.427.
  18. Madenci, E. and Ozutok, A. (2017), "Variational Approximate and Mixed-Finite Element Solution for Static Analysis of Laminated Composite Plates", Solid State Phenomena, 267, 35-39. http://doi.org/10.4028/www.scientific.net/SSP.267.35.
  19. Madenci, E. and Ozutok, A. (2020), "Variational approximate for high order bending analysis of laminated composite plates", Struct. Eng. Mech., 73(1), 97-108. http://doi.org/10.12989/sem.2020.73.1.097.
  20. Madenci, E., Ozkilic, Y.O. and Gemi, L. (2020), "Experimental and theoretical investigation on flexure performance of pultruded GFRP composite beams with damage analyses", Compos. Struct., 242, 112162. http://doi.org/10.1016/j.compstruct.2020.112162.
  21. Ozutok, A. and Madenci, E. (2017), "Static analysis of laminated composite beams based on higher-order shear deformation theory by using mixed-type finite element method", Int. J. Mech. Sci., 130, 234-243. http://doi.org/10.1016/j.ijmecsci.2017.06.013.
  22. Rafiee, R. (2013), "Experimental and theoretical investigations on the failure of filament wound GRP pipes", Compos. Part B Eng., 45(1), 257-267. http://doi.org/10.1016/j.compositesb.2012.04.009.
  23. Rafiee, R. and Abbasi, F. (2020), "Numerical and Experimental Analyses of the Hoop Tensile Strength of Filament-Wound Composite Tubes", Mech. Compos. Mater., 56(4), 423-436. http://doi.org/10.1007/s11029-020-09894-2.
  24. Rafiee, R. and Elasmi, F. (2017), "Theoretical modeling of fatigue phenomenon in composite pipes", Compos. Struct., 161, 256-263. http://doi.org/10.1016/j.compstruct.2016.11.054.
  25. Rafiee, R. and Ghorbanhosseini, A. (2020), "Analyzing the longterm creep behavior of composite pipes: Developing an alternative scenario of short-term multi-stage loading test", Compos. Struct., 254, 112868. http://doi.org/10.1016/j.compstruct.2020.112868.
  26. Rafiee, R. and Habibagahi, M.R. (2018), "Evaluating mechanical performance of GFRP pipes subjected to transverse loading", Thin Wall. Struct., 131, 347-359. http://doi.org/10.1016/j.tws.2018.06.037.
  27. Rafiee, R. and Sharifi, P. (2019), "Stochastic failure analysis of composite pipes subjected to random excitation", Construct. Build. Mater., 224, 950-961. http://doi.org/10.1016/j.conbuildmat.2019.07.107.
  28. Takahashi, K., Ban, K. and Sakai, T. (1984), "Mechanical properties of FRP-FW pipes", Compos. Struct., 2(2), 91-104. http://doi.org/10.1016/0263-8223(84)90023-0.
  29. Topal, U. (2017), "Buckling load optimization of laminated composite stepped columns", Struct. Eng. Mech., 62(1), http://doi.org/10.12989/sem.2017.62.1.107.
  30. Tsai, S.W. and Hahn, T.H. (1980), Introduction to Composite Materials, Technomic Publishing Company, Lancaster, Pennsylvania, USA.
  31. Yang, X., Bai, Y. and Ding, F. (2015), "Structural performance of a large-scale space frame assembled using pultruded GFRP composites", Compos. Struct., 133, 986-996. http://doi.org/10.1016/j.compstruct.2015.07.120.
  32. Yu, T., Zhang, S., Huang, L. and Chan, C. (2017), "Compressive behavior of hybrid double-skin tubular columns with a large rupture strain FRP tube", Compos. Struct., 171, 10-18. http://doi.org/10.1016/j.compstruct.2017.03.013.
  33. Yu, T., Zhao, H., Ren, T. and Remennikov, A. (2019), "Novel hybrid FRP tubular columns with large deformation capacity: Concept and behaviour", Compos. Struct., 212, 500-512. http://doi.org/10.1016/j.compstruct.2019.01.055.