The Journal of Advanced Prosthodontics

  • 제12권4호
  • /
  • Pages.197-203
  • /
  • 2020
  • /
  • 2005-7806(pISSN)
  • /
  • 2005-7814(eISSN)
대한치과보철학회 (The Korean Academy of Prosthodonitics)
권호 표지
DOI QR코드

DOI QR Code

Impact of multiple firings and resin cement type on shear bond strength between zirconia and resin cements

  • Oguz, Ece Irem (Department of Prosthodontics, Faculty of Dentistry, Ankara University) ;
  • Ozgur, Merve Erdog (Department of Prosthodontics, Faculty of Dentistry, Baskent University) ;
  • Sungur, Sercan (Department of Prosthodontics, Faculty of Dentistry, Ankara University) ;
  • Uctasli, Sadullah (Department of Prosthodontics, Faculty of Dentistry, Ankara University)
  • 투고 : 2019.11.21
  • 심사 : 2020.07.01
  • 발행 : 2020.08.31
PDF 다운로드
⟨ 이전 논문 다음 논문 ⟩

초록

PURPOSE. The aim of this study was to evaluate the effect of multiple firings on the bond strength between yttriatetragonal zirconia polycrystals (Y-TZP) and 2 types of resin cements. MATERIALS AND METHODS. Sixty 3Y-TZP specimens (LAVA Frame Multi) were divided into 3 groups depending on the following firing procedures: (1) 2-firing cycles, (2) 5-firing cycles, (3) 10-firing cycles. Two samples from each group were investigated by using SEM to determine the morphological changes. All specimens were treated with 125 ㎛ airborne-particle abrasion and the surface roughness of each specimen was measured. The specimens from each firing group were then further divided into 2 subgroups (n = 9) to apply 2 types of resin cement (MDP-free resin cement: RelyX Unicem-RU, and MDP containing resin cement: Panavia F 2.0-PA). The shear bond strength (SBS) test was performed and failure types of all the debonded specimens were classified by using a stereomicroscope as adhesive, cohesive, and mixed. The statistical analysis of surface roughness and SBS data were performed by using 1-way ANOVA and 2-way ANOVA followed by Tukey-HSD tests (α=.05). Failure modes were calculated as a percentage for each group. RESULTS. The bond strength of RU and PA to the specimens obtained with 2 firings were not statistically different from each other (P=.1). However, the SBS values of PA were found to be significantly higher than RU for the specimens obtained with 5 and 10 firing cycles (P=.001 and P=.02, respectively). Surface roughness analysis revealed no statistical difference between groups (P=.2). The SEM analysis of samples fired 5- and 10- times showed irregularities and boundary loss in zirconia grains, and empty spaces between zirconia grains. CONCLUSION. The bond strength of PA cement was higher than that of RU to the zirconia subjected to repeated firings (5 and 10 firing cycles). When zirconia is subjected to multiple firings, using MDP-containing resin cement can be recommended.

키워드

참고문헌

  1. Kim MJ, Ahn JS, Kim JH, Kim HY, Kim WC. Effects of the sintering conditions of dental zirconia ceramics on the grain size and translucency. J Adv Prosthodont 2013;5:161-6. https://doi.org/10.4047/jap.2013.5.2.161
  2. Tang X, Nakamura T, Usami H, Wakabayashi K, Yatani H. Effects of multiple firings on the mechanical properties and microstructure of veneering ceramics for zirconia frameworks. J Dent 2012;40:372-80. https://doi.org/10.1016/j.jdent.2012.01.014
  3. Pecho OE, Ghinea R, Ionescu AM, Cardona Jde L, Paravina RD, Perez Mdel M. Color and translucency of zirconia ceramics, human dentine and bovine dentine. J Dent 2012;40:e34-40.
  4. Tabatabaian F, Taghizade F, Namdari M. Effect of coping thickness and background type on the masking ability of a zirconia ceramic. J Prosthet Dent 2018;119:159-65. https://doi.org/10.1016/j.prosdent.2017.03.009
  5. Spazzin AO, Schestatsky R, Ness CRB, Alessandretti R, Pereira GKR. Obtaining optimal esthetics with veneered zirconia and lithium disilicate frameworks on substrates of different colors. J Esthet Restor Dent 2020;32:540-4. https://doi.org/10.1111/jerd.12578
  6. Turgut S. Optical properties of currently used zirconia-based esthetic restorations fabricated with different techniques. J Esthetic and Restor Dent 2020;32:26-33. https://doi.org/10.1111/jerd.12533
  7. Zhang Y, Lawn BR. Novel Zirconia Materials in Dentistry. J Dent Res 2018;97:140-7. https://doi.org/10.1177/0022034517737483
  8. Tong H, Tanaka CB, Kaizer MR, Zhang Y. Characterization of three commercial Y-TZP ceramics produced for their high-translucency, high-strength and high-surface area. Ceram Int 2016;42:1077-85. https://doi.org/10.1016/j.ceramint.2015.09.033
  9. Alkurt M, Yesil Duymus Z, Gundogdu M. Effects of multiple firings on the microstructure of zirconia and veneering ceramics. Dent Mater J 2016;35:776-81. https://doi.org/10.4012/dmj.2015-429
  10. Oilo M, Gjerdet NR, Tvinnereim HM. The firing procedure influences properties of a zirconia core ceramic. Dent Mater 2008;24:471-5. https://doi.org/10.1016/j.dental.2007.04.008
  11. O'Brien WJ, Kay KS, Boenke KM, Groh CL. Sources of color variation on firing porcelain. Dent Mater 1991;7:170-3. https://doi.org/10.1016/0109-5641(91)90038-Z
  12. Uludag B, Usumez A, Sahin V, Eser K, Ercoban E. The effect of ceramic thickness and number of firings on the color of ceramic systems: an in vitro study. J Prosthet Dent 2007;97:25-31. https://doi.org/10.1016/j.prosdent.2006.11.002
  13. Ryan DPO, Fais LMG, Antonio SG, Hatanaka GR, Candido LM, Pinelli LAP. Y-TZP zirconia regeneration firing: Microstructural and crystallographic changes after grinding. Dent Mater J 2017;36:447-53. https://doi.org/10.4012/dmj.2016-124
  14. Vatali A, Kontonasaki E, Kavouras P, Kantiranis N, Papadopoulou L, Paraskevopoulos KM, Koidis P. Effect of heat treatment and in vitro aging on the microstructure and mechanical properties of cold isostatic-pressed zirconia ceramics for dental restorations. Dent Mater 2014;30:e272-82.
  15. Subasi MG, Inan O. Influence of surface treatments and resin cement selection on bonding to zirconia. Lasers Med Sci 2014;29:19-27. https://doi.org/10.1007/s10103-012-1221-1
  16. Tanis MC, Akcaboy C. Effects of different surface treatment methods and MDP monomer on resin cementation of zirconia ceramics an in vitro study. J Lasers Med Sci 2015;6:174-81. https://doi.org/10.15171/jlms.2015.15
  17. Petrauskas A, Novaes Olivieri KA, Pupo YM, Berger G, Goncalves Betiol EA. Influence of different resin cements and surface treatments on microshear bond strength of zirconia-based ceramics. J Conserv Dent 2018;21:198-204. https://doi.org/10.4103/JCD.JCD_190_17
  18. Blatz MB, Sadan A, Kern M. Resin-ceramic bonding: a review of the literature. J Prosthet Dent 2003;89:268-74. https://doi.org/10.1067/mpr.2003.50
  19. Yoshida K, Tsuo Y, Atsuta M. Bonding of dual-cured resin cement to zirconia ceramic using phosphate acid ester monomer and zirconate coupler. J Biomed Mater Res B Appl Biomater 2006;77:28-33. https://doi.org/10.1002/jbm.b.30424
  20. Khan AA, Al Kheraif AA, Jamaluddin S, Elsharawy M, Divakar DD. Recent trends in surface treatment methods for bonding composite cement to zirconia: a reveiw. J Adhes Dent 2017;19:7-19.
  21. Go EJ, Shin Y, Park JW. Evaluation of the microshear bond strength of MDP-containing and non-MDP-containing selfadhesive resin cement on zirconia restoration. Oper Dent 2019;44:379-85. https://doi.org/10.2341/18-132-L
  22. Geramipanah F, Majidpour M, Sadighpour L, Fard MJ. Effect of artificial saliva and pH on shear bond strength of resin cements to zirconia-based ceramic. Eur J Prosthodont Restor Dent 2013;21:5-8.
  23. Keul C, Liebermann A, Roos M, Uhrenbacher J, Stawarczyk B, Ing D. The effect of ceramic primer on shear bond strength of resin composite cement to zirconia: a function of water storage and thermal cycling. J Am Dent Assoc 2013;144:1261-71. https://doi.org/10.14219/jada.archive.2013.0055
  24. Akay C, Cakirbay Tanis M, Sen M. Effects of hot chemical etching and 10-metacryloxydecyl dihydrogen phosphate (MDP) monomer on the bond strength of zirconia ceramics to resin-based cements. J Prosthodont 2017;26:419-23. https://doi.org/10.1111/jopr.12435
  25. Grasel R, Santos MJ, Rego HC, Rippe MP, Valandro LF. Effect of resin luting systems and alumina particle air abrasion on bond strength to zirconia. Oper Dent 2018;43:282-90. https://doi.org/10.2341/15-352-L
  26. Yoon HI, Yeo IS, Yi YJ, Kim SH, Lee JB, Han JS. Effect of surface treatment and liner material on the adhesion between veneering ceramic and zirconia. J Mech Behav Biomed Mater 2014;40:369-74. https://doi.org/10.1016/j.jmbbm.2014.09.017
  27. Bartolo D, Cassar G, Al-Haj Husain N, Ozcan M, Camilleri J. Effect of polishing procedures and hydrothermal aging on wear characteristics and phase transformation of zirconium dioxide. J Prosthet Dent 2017;117:545-51. https://doi.org/10.1016/j.prosdent.2016.09.004
  28. Cakir-Omur T, Gozneli R, Ozkan Y. Effects of silica coating by physical vapor deposition and repeated firing on the lowtemperature degradation and flexural strength of a zirconia ceramic. J Prosthodont 2019;28:e186-94. https://doi.org/10.1111/jopr.12618
  29. Hjerppe J, Vallittu PK, Froberg K, Lassila LV. Effect of sintering time on biaxial strength of zirconium dioxide. Dent Mater 2009;25:166-71. https://doi.org/10.1016/j.dental.2008.05.011
  30. Kelly JR, Denry I. Stabilized zirconia as a structural ceramic: an overview. Dent Mater 2008;24:289-98. https://doi.org/10.1016/j.dental.2007.05.005
  31. Amaral M, Valandro LF, Bottino MA, Souza RO. Low-temperature degradation of a Y-TZP ceramic after surface treatments. J Biomed Mater Res B Appl Biomater 2013;101:1387-2. https://doi.org/10.1002/jbm.b.32957
  32. Kim HT, Han JS, Yang JH, Lee JB, Kim SH. The effect of low temperature aging on the mechanical property & phase stability of Y-TZP ceramics. J Adv Prosthodont 2009;1:113-7. https://doi.org/10.4047/jap.2009.1.3.113-7
  33. Kelly PM, Francis Rose LR. The martensitic transformation in ceramics - its role in transformation toughening. Prog Mater Sci 2002;47:463-557. https://doi.org/10.1016/S0079-6425(00)00005-0
  34. Zhang Y, Lawn BR, Rekow ED, Thompson VP. Effect of sandblasting on the long-term performance of dental ceramics. J Biomed Mater Res B Appl Biomater 2004;71:381-6.
  35. Denry IL, Peacock JJ, Holloway JA. Effect of heat treatment after accelerated aging on phase transformation in 3Y-TZP. J Biomed Mater Res B Appl Biomater 2010;93:236-43.
  36. Papia E, Larsson C, du Toit M, Vult von Steyern P. Bonding between oxide ceramics and adhesive cement systems: a systematic review. J Biomed Mater Res B Appl Biomater 2014;102:395-413. https://doi.org/10.1002/jbm.b.33013
  37. Munoz EM, Longhini D, Antonio SG, Adabo GL. The effects of mechanical and hydrothermal aging on microstructure and biaxial flexural strength of an anterior and a posterior monolithic zirconia. J Dent 2017;63:94-102. https://doi.org/10.1016/j.jdent.2017.05.021
  38. Chen Y, Lu Z, Qian M, Zhang H, Chen C, Xie H, Tay FR. Chemical affinity of 10-methacryloyloxydecyl dihydrogen phosphate to dental zirconia: effects of molecular structure and solvents. Dent Mater 2017;33:e415-27. https://doi.org/10.1016/j.dental.2017.09.013
  39. Luthy H, Loeffel O, Hammerle CH. Effect of thermocycling on bond strength of luting cements to zirconia ceramic. Dent Mater 2006;22:195-200. https://doi.org/10.1016/j.dental.2005.04.016
  40. Valverde GB, Coelho PG, Janal MN, Lorenzoni FC, Carvalho RM, Surface characterisation and bonding of Y-TZP following non-thermal plasma treatment. J Dent 2013;41:51-9. https://doi.org/10.1016/j.jdent.2012.10.002
  41. Feitosa VP, Sauro S, Ogliari FA, Ogliari AO, Yoshihara K, Zanchi CH, Correr-Sobrinho L, Sinhoreti MA, Correr AB, Watson TF, Van Meerbeek B. Impact of hydrophilicity and length of spacer chains on the bonding of functional monomers. Dent Mater 2014;30:e317-23. https://doi.org/10.1016/j.dental.2014.06.006
  42. Feitosa VP, Sauro S, Ogliari FA, Stansbury JW, Carpenter GH, Watson TF, Sinhoreti MA, Correr AB. The role of spacer carbon chain in acidic functional monomers on the physicochemical properties of self-etch dental adhesives. J Dent 2014;42:565-74. https://doi.org/10.1016/j.jdent.2014.02.009
  43. Yang L, Chen B, Xie H, Chen Y, Chen Y, Chen C. Durability of resin bonding to zirconia using products containing 10-methacryloyloxydecyl dihydrogen phosphate. J Adhes Dent 2018;20:279-87.
  44. Okutan Y, Yucel MT, Gezer T, Donmez MB. Effect of airborne particle abrasion and sintering order on the surface roughness and shear bond strength between Y-TZP ceramic and resin cement. Dent Mater J 2019;38:241-9. https://doi.org/10.4012/dmj.2018-051
  45. Pandoleon P, Kontonasaki E, Kantiranis N, Pliatsikas N, Patsalas P, Papadopoulou L, Zorba T, Paraskevopoulos KM, Koidis P. Aging of 3Y-TZP dental zirconia and yttrium depletion. Dent Mater 2017;33:e385-92. https://doi.org/10.1016/j.dental.2017.07.011