DOI QR코드

DOI QR Code

Numerical study on force transfer mechanism in through gusset plates of SCBFs with HSS columns & beams

  • Ebrahimi, S. (School of Civil Engineering, College of Engineering, University of Tehran) ;
  • Zahrai, S.M. (Center of Excellence for Engineering and Management of Civil Infrastructures, School of Civil Engineering, College of Engineering, University of Tehran) ;
  • Mirghaderi, S.R. (School of Civil Engineering, College of Engineering, University of Tehran)
  • Received : 2018.02.08
  • Accepted : 2019.05.06
  • Published : 2019.06.25

Abstract

In Special Concentrically Braced Frames (SCBFs), vertical and horizontal components of the brace force must be resisted by column and beam, respectively but normal force component existing at the gusset plate-to-column and beam interfaces, creates out-of-plane action making distortion in column and beam faces adjacent to the gusset plate. It is a main concern in Hollow Structural Section (HSS) columns and beams where their webs and gusset plate are not in the same plane. In this paper, a new gusset plate passing through the HSS columns and beams, named as through gusset plate, is proposed to study the force transfer mechanism in such gusset plates of SCBFs compared to the case with conventional gusset plates. For this purpose, twelve SCBFs with diagonal brace and HSS columns and twelve SCBFs with chevron brace and HSS columns and beams are considered. For each frame, two cases are considered, one with through gusset plates and the other with conventional ones. Based on numerical results, using through gusset plates prevents distortion and out-of-plane deformation at HSS column and beam faces adjacent to the gusset plate helping the entire column and beam cross-sections to resist respectively vertical and horizontal components of the brace force. Moreover, its application increases energy dissipation, lateral stiffness and strength around 28%, 40% and 32%, respectively, improving connection behavior and raising the resistance of the normal force components at the gusset plate-to-HSS column and beam interfaces to approximately 4 and 3.5 times, respectively. Finally, using such through gusset plates leads to better structural performance particularly for HSS columns and beams with larger width-to-thickness ratio elements.

Keywords

Acknowledgement

Supported by : Iran National Science Foundation (INSF)

References

  1. ABAQUS 6.12 [Computer software], Dassault Systemes Simulia Corporation, Providence, RI, USA.
  2. AISC (2016a), Specification for structural steel buildings, American Institute of Steel Construction; Chicago, IL, USA.
  3. AISC (2016b), Seismic provisions for structural steel buildings, American Institute of Steel Construction; Chicago, IL, USA.
  4. Alipour, A. (2009), "Gusset Plate Connections in Concentrically Braced Steel Structures", In: Structures Congress: Don't Mess with Structural Engineers: Expanding Our Role, pp. 1-10.
  5. Applied Technology Council (ATC) (1992), Guidelines for cyclic seismic testing of components of steel structures.
  6. Ebrahimi, S., Mirghaderi, S.R. and Zahrai, S.M. (2019), "Proposed design procedure for gusset plate dimensions and force distribution at its interfaces to beam and column", Eng. Struct., 178, 554-572. https://doi.org/10.1016/j.engstruct.2018.09.066
  7. Erfani, S., Asnafi, A.A. and Goudarzi, A. (2016), "Connection of I-beam to box-column by a short stub beam", J. Constr. Steel Res., 127, 136-150. https://doi.org/10.1016/j.jcsr.2016.07.025
  8. Fell, B.V. (2008), "Large-scale testing and simulation of earthquake-induced ultra-low cycle fatigue in bracing members subjected to cyclic inelastic buckling", Doctoral Dissertation; University of California at Davis.
  9. Fell, B.V. and Kanvinde, A.M. (2010), "Tensile forces for seismic design of braced frame connections, Experimental results", J. Constr. Steel Res., 66(4), 496-503. https://doi.org/10.1016/j.jcsr.2009.10.002
  10. FEMA (2000), FEMA 351: Recommended Seismic Evaluation and Upgrade Criteria for Existing Welded Steel Moment Frame Buildings, Federal Emergency Management Agency, Washington, DC, USA.
  11. Goswami, R. and Murty, C.V.R. (2009), "Externally reinforced welded I-beam-to-box-column seismic connection", J. Eng. Mech., 136(1), 23-30. https://doi.org/10.1061/(asce)0733-9399(2010)136:1(23)
  12. Hadianfard, M.A. and Khakzad, A.R. (2016), "Inelastic buckling and post-buckling behavior of gusset plate connections", Steel Compos. Struct., Int. J., 22(2), 411-427. http://dx.doi.org/10.12989/scs.2016.22.2.411
  13. Izadi, A. and Aghakouchak, A.A. (2018), "Evaluation of seismic criteria of built-up special concentrically braced frames", Steel Compos. Struct., Int. J., 29(1), 23-37. http://dx.doi.org/10.12989/scs.2018.29.1.023
  14. Kiamanesh, R., Abolmaali, A. and Ghassemieh, M. (2010), "The effect of stiffeners on the strain patterns of the welded connection zone", J. Constr. Steel Res., 66(1), 19-27. https://doi.org/10.1016/j.jcsr.2009.07.010
  15. Kosteski, N. and Packer, J.A. (2003), "Longitudinal plate and through plate-to-hollow structural section welded connections", J. Struct. Eng., 129(4), 478-486. https://doi.org/10.1061/(ASCE)0733-9445(2003)129:4(478)
  16. Lai, J.W. and Mahin, S.A. (2013), "Experimental and analytical studies on the seismic behavior of conventional and hybrid braced frames", Pacific Earthquake Engineering Research Center.
  17. Lee, S.L., Ting, L.C. and Shanmugam, N.E. (1993), "Use of external T-stiffeners in box-column to I-beam connections", J. Constr. Steel Res., 26(2-3), 77-98. https://doi.org/10.1016/0143-974X(93)90030-V
  18. Liu, J. and Astaneh-Asl, A. (2000), "Cyclic testing of simple connections including effects of slab", J. Struct. Eng., 126(1), 32-39. https://doi.org/10.1061/(ASCE)0733-9445(2000)126:1(32)
  19. Lopez, W.A., Gwie, D.S., Lauck, T.W. and Saunders, C. (2004), "Structural design and experimental verification of a bucklingrestrained braced frame system", Eng. J., 41(4), 177-186.
  20. Mirghaderi, S.R., Torabian, S. and Keshavarzi, F. (2010), "I-beam to box-column connection by a vertical plate passing through the column", J. Struct. Eng., 32(8), 2034-2048. https://doi.org/10.1016/j.engstruct.2010.03.002
  21. Nunez, E., Torres, R. and Herrera, R. (2017), "Seismic performance of moment connections in steel moment frames with HSS columns", Steel Compos. Struct., Int. J., 25(3), 271-286. http://dx.doi.org/10.12989/scs.2017.25.3.271
  22. Sabbagh, A.B., Chan, T.M. and Mottram, J.T. (2013), "Detailing of I-beam-to-CHS column joints with external diaphragm plates for seismic actions", J. Constr. Steel Res., 88, 21-33. https://doi.org/10.1016/j.jcsr.2013.05.006
  23. Sabelli, R. and Hohbach, D. (1999), "Design of cross-braced frames for predictable buckling behavior", J. Struct. Eng., 125(2), 163-168. https://doi.org/10.1061/(ASCE)0733-9445(1999)125:2(163)
  24. Shaback, B. and Brown, T. (2003), "Behavior of square hollow structural steel braces with end connections under reversed cyclic axial loading", Can. J. Civil Eng., 30(4), 745-753. https://doi.org/10.1139/l03-028
  25. Shin, K.J., Kim, Y.J., Oh, Y.S. and Moon, T.S. (2004), "Behavior of welded CFT column to H-beam connections with external stiffeners", J. Eng. Struct., 26(13), 1877-1887. https://doi.org/10.1016/j.engstruct.2004.06.016
  26. Song, Q.Y., Heidarpour, A., Zhao, X.L. and Han, L.H. (2016), "Performance of double-angle bolted steel I-beam to hollow square column connections under static and cyclic loadings", Int. J. Struct. Stabil. Dyn., 16(2), 1450098. https://doi.org/10.1142/S0219455414500989
  27. Thornton, W.A. (1984), "Bracing connections for heavy construction", Eng. J., 21(3), 139-148.
  28. Thornton, W.A. and Muir, L.S. (2008), "Vertical bracing connections in the seismic regime", Proceedings of connections VI, AISC.
  29. Ting, L.C., Shanmugam, N.E. and Lee, S.L. (1991), "Box-column to I-beam connections with external stiffeners", J. Constr. Steel Res., 18(3), 209-226. https://doi.org/10.1016/0143-974X(91)90026-W
  30. Torabian, S., Mirghaderi, S.R. and Keshavarzi, F. (2012), "Moment-connection between I-beam and built-up square column by a diagonal through plate", J. Constr. Steel Res., 70, 385-401. https://doi.org/10.1016/j.jcsr.2011.10.017
  31. Tremblay, R. (2002), "Inelastic seismic response of steel bracing members", J. Constr. Steel Res., 58(5), 665-701. https://doi.org/10.1016/S0143-974X(01)00104-3
  32. Uriz, P. and Mahin, S. (2004), "Summary of test results for UC Berkeley special concentric braced frame specimen", No. 1 (SCBF-1), Preliminary Observations, University of California, Berkeley, CA, USA.
  33. Whitmore, R.E. (1952), "Experimental investigation of stresses in gusset plates", Engineering Experiment Station, University of Tennessee, Knoxville, TN, USA.
  34. Williams, G.C. and Richard, R.M. (1986), "Steel Connection Design Based on Inelastic Finite Element Analysis", Report of the Department of Civil Engineering and Engineering Mechanics; The University of Arizona.
  35. Zahrai, S.M. (2015), "Cyclic Testing of Chevron Braced Steel Frames with IPE shear panels", Steel Compos. Struct., Int. J., 19(5), 1167-1184. http://dx.doi.org/10.12989/scs.2015.19.5.1167
  36. Zahrai, S.M. and Jalali, M. (2014), "Experimental and analytical investigation on seismic behavior of ductile steel knee braced frames", Steel Compos. Struct., Int. J., 16(1), 1-21. http://dx.doi.org/10.12989/scs.2014.16.1.001

Cited by

  1. Influence of internal pores and graphene platelets on vibration of non-uniform functionally graded columns vol.35, pp.2, 2019, https://doi.org/10.12989/scs.2020.35.2.295
  2. Further study on improvement on strain concentration in through-diaphragm connection vol.39, pp.2, 2019, https://doi.org/10.12989/scs.2021.39.2.135