DOI QR코드

DOI QR Code

Bearing resistance design of stainless steel bolted connections at ambient and elevated temperatures

  • Cai, Yancheng (Department of Civil Engineering, The University of Hong Kong) ;
  • Young, Ben (Department of Civil Engineering, The University of Hong Kong)
  • 투고 : 2018.07.23
  • 심사 : 2018.08.22
  • 발행 : 2018.10.25

초록

In recent years, significant progress has been made in developing design rules for stainless steel members, while the investigation on bolted connections is relatively limited, in particular at elevated temperatures. In this paper, experimental and numerical investigations on stainless steel bolted connections at ambient and elevated temperatures from the literature were reviewed. Firstly, the research program that focused on structural behavior of cold-formed stainless steel (CFSS) bolted connections at elevated temperatures carried out by the authors were summarized. Over 400 CFSS single shear and double shear bolted connection specimens were tested. The tests were conducted in the temperature ranged from 22 to $950^{\circ}C$ using both steady state and transient state test methods. It is shown that the connection strengths decrease as the temperature increases in the similar manner for the steady state test results and the transient state test results. Generally, the deterioration of the connection strengths showed a similar tendency of reduction to those of the material properties for the same type of stainless steel regardless of different connection types and different configurations. It is also found that the austenitic stainless steel EN 1.4571 generally has better resistance than the stainless steel EN 1.4301 and EN 1.4162 for bolted connections at elevated temperatures. Secondly, extensive parametric studies that included 450 specimens were performed using the verified finite element models. Based on both the experimental and numerical results, bearing factors are proposed for bearing resistances of CFSS single shear and double shear bolted connections that subjected to bearing failure in the temperature ranged from 22 to $950^{\circ}C$. The bearing resistances of bolted connections obtained from the tests and numerical analyses were compared with the nominal strengths calculated from the current international stainless steel specifications, and also compared with the predicted strengths calculated using the proposed design equations. It is shown that the proposed design equations are generally more accurate and reliable than the current design rules in predicting the bearing resistances of CFSS (EN 1.4301, EN 1.4571 and EN 1.4162) bolted connections at elevated temperatures. Lastly, the proposed design rules were further assessed by the available 58 results of stainless steel bolted connections subjected to bearing failure in the literature. It is found that the proposed design rules are also applicable to the bearing resistance design of other stainless steel grades, including austenitic stainless steel (EN 1.4306), ferritic stainless steel (EN 1.4016) and duplex stainless steel (EN 1.4462).

키워드

과제정보

연구 과제 주관 기관 : Council of the Hong Kong Special Administrative Region

참고문헌

  1. ABAQUS (2010), ABAQUS analysis user's manual; Version 6.10. ABAQUS, Inc.
  2. Agheshlui, H., Goldsworthy, H., Gad, E. and Mirza, O. (2017), "Anchored blind bolted composite connection to a concrete filled steel tubular column", Steel Compos. Struct., Int. J., 23(1), 115-130. https://doi.org/10.12989/scs.2017.23.1.115
  3. AISI (2016), North American Specification for the Design of Cold-formed Steel Structural Members, North American Coldformed Steel Specification; American Iron and Steel Institute (AISI), AISI S100-2016, Washington, D.C., USA.
  4. AS-2291 (1979), Methods for the tensile testing of metals at elevated temperatures, Standards Australia, Sydney, Australia.
  5. ASCE (2002), Specification for the design of cold-formed stainless steel structural members, American Society of Civil Engineers (ASCE); ASCE Standard, SEI/ASCE-8-02, Reston, VA, USA.
  6. AS/NZS (2001), Cold-formed stainless steel structures, Australian /New Zealand Standard (AS/NZS), AS/NZS 4673:2001, Standards Australia, Sydney, Australia.
  7. Baddoo, N.R. (2008), "Stainless steel in construction: A review of research, applications, challenges and opportunities", J. Constr. Steel Res., 64(11), 1199-1206. https://doi.org/10.1016/j.jcsr.2008.07.011
  8. Beena, K., Naveen, K. and Shruti, S. (2017), "Behaviour of bolted connections in concrete-filled steel tubular beamcolumn joints", Steel Compos. Struct., Int. J., 25(4), 443-456.
  9. Bouchair, A., Averseng, J. and Abidelah, A. (2008), "Analysis of the behaviour of stainless steel bolted connections", J. Constr. Steel Res., 64(11), 1264-1274. https://doi.org/10.1016/j.jcsr.2008.07.009
  10. BS EN ISO 3506-1 (1998), "Mechanical properties of corrosionresistant stainless steel fasteners-Part 1: Bolts, screws and studs", BS EN ISO 3506-1.
  11. Cai, Y. and Young, B. (2014a), "Structural behavior of coldformed stainless steel bolted connections", Thin-Wall. Struct., 83, 147-156. https://doi.org/10.1016/j.tws.2014.01.014
  12. Cai, Y. and Young, B. (2014b), "Behavior of cold-formed stainless steel single shear bolted connections at elevated temperatures", Thin-Wall. Struct., 75, 63-75. https://doi.org/10.1016/j.tws.2013.10.010
  13. Cai, Y. and Young, B. (2014c), "Transient state test of cold-formed stainless steel single shear bolted connections", Eng. Struct., 81, 1-9. https://doi.org/10.1016/j.engstruct.2014.09.031
  14. Cai, Y. and Young, B. (2015), "High temperature tests of coldformed stainless steel double shear bolted connections", J. Constr. Steel Res., 104, 49-63. https://doi.org/10.1016/j.jcsr.2014.09.015
  15. Cai, Y. and Young, B. (2016), "Bearing factors of cold-formed stainless steel double shear bolted connections at elevated temperatures", Thin-Wall. Struct., 98, 212-229. https://doi.org/10.1016/j.tws.2015.04.021
  16. Cai, Y. and Young, B. (2018), "Fire resistance of stainless steel single shear bolted connections", Thin-Wall. Struct., 130, 332-346. https://doi.org/10.1016/j.tws.2018.05.004
  17. Chang, K.H., Hsu, C.M., Sheu, S.R. and Pan, W.F. (2005), "Viscoplastic response and collapse of 316L stainless steel tubes under cyclic bending", Steel Compos. Struct., Int. J., 5(5), 359-374. https://doi.org/10.12989/scs.2005.5.5.359
  18. EC1-1.2 (2002), Eurocode 1 - actions on structures - Part 1-2: general actions - actions on structures exposed to fire, European Committee for Standardization, EN 1991-1-2:2002, Brussels, Belgium.
  19. EC3-1.4 (2006), Eurocode 3: Design of steel structures - Part 1.4: General rules - Supplementary rules for stainless steels, European Committee for Standardization, BS EN 1993-1-4:2006, Brussels, Belgium.
  20. EC3-1.8 (2005), Eurocode 3: Design of steel structures-Part 1.8: Design of joints, European Committee for Standardization, BS EN 1993-1-8:2005, CEN, Brussels, Belgium.
  21. Ellobody, E. and Young, B. (2007), "Investigation of coldformed stainless steel non-slender circular hollow section columns", Steel Compos. Struct., Int. J., 7(4), 321-337. https://doi.org/10.12989/scs.2007.7.4.321
  22. Gardner, L. and Baddoo, N.R. (2006), "Fire testing and design of stainless steel structures", J. Constr. Steel Res., 62(6), 532-543. https://doi.org/10.1016/j.jcsr.2005.09.009
  23. Huang, Y. and Young, B. (2014), "Experimental and numerical investigation of cold-formed lean duplex stainless steel flexural members", Thin-Wall. Struct., 73, 216-228.
  24. Kim, T.S. and Cho, T.J. (2013), "Influence of microstructure difference of stainless steels on the strength and fracture of bolted connections", ISIJ Int., 53(2), 365-374. https://doi.org/10.2355/isijinternational.53.365
  25. Kim, T.S. and Kuwamura, H. (2007), "Finite element modeling of bolted connections in thin-walled stainless steel plates under static shear", Thin-Wall. Struct., 45(4), 407-421. https://doi.org/10.1016/j.tws.2007.03.006
  26. Kim, T.S., Kuwamura, H. and Cho, T.J. (2008), "A parametric study on ultimate strength of single shear bolted connections with curling", Thin-Wall. Struct., 46(1), 38-53. https://doi.org/10.1016/j.tws.2007.08.009
  27. Kiymaz, G. (2009), "Investigations on the bearing strength of stainless steel bolted plates under in-plane tension", Steel Compos. Struct., Int. J., 9(2), 173-189. https://doi.org/10.12989/scs.2009.9.2.173
  28. Leong, S.H., Ramli Sulong, N.H. and Jameel, M. (2016), "Bolted connections to tubular columns at ambient and elevated temperatures - A review", Steel Compos. Struct., Int. J., 21(2), 303-321. https://doi.org/10.12989/scs.2016.21.2.303
  29. Li, S., Li, Q., Jiang, H., Zhang, H., Yan, L. and Jiang, W. (2018), "Experimental study on a new type of assembly bolted endplate connection", Steel Compos. Struct., Int. J., 26(4), 463-471.
  30. Salih, E.L., Gardner, L. and Nethercot, D.A. (2010), "Numerical investigation of net section failure in stainless steel bolted connections", J. Constr. Steel Res., 66(12), 1455-1466. https://doi.org/10.1016/j.jcsr.2010.05.012
  31. Salih, E.L., Gardner, L. and Nethercot, D.A. (2011), "Bearing failure in stainless steel bolted connections", Eng. Struct., 33(2), 549-562. https://doi.org/10.1016/j.engstruct.2010.11.013
  32. Salih, E.L., Gardner, L. and Nethercot, D.A. (2013), "Numerical study of stainless steel gusset plate connections", Eng. Struct., 49, 448-464. https://doi.org/10.1016/j.engstruct.2012.11.032
  33. SCI/Euro Inox (2006), "Design manual for structural stainless steel", In: The Steel Construction Institute and Euro Inox, (3rd Ed.), Building series, Vol. 3.
  34. Theofanous, M. and Gardner, L. (2010), "Experimental and numerical studies of lean duplex stainless steel beams", J. Constr. Steel Res., 66, 816-825. https://doi.org/10.1016/j.jcsr.2010.01.012
  35. Theofanous, M. and Gardner, L. (2012), "Effect of element interaction and material nonlinearity on the ultimate capacity of stainless steel cross-sections", Steel Compos. Struct., Int. J., 12(1), 73-92. https://doi.org/10.12989/scs.2012.12.1.073
  36. Yan, S. and Young, B. (2012), "Bearing factors for single shear bolted connections of thin sheet steels at elevated temperatures", Thin-Wall. Struct., 52, 126-142. https://doi.org/10.1016/j.tws.2011.12.008
  37. Young, B. and Ellobody, E. (2006), "Column design of coldformed stainless steel slender circular hollow sections", Steel Compos. Struct., Int. J., 6(4), 285-302. https://doi.org/10.12989/scs.2006.6.4.285

피인용 문헌

  1. Experimental and numerical investigation on post-earthquake fire behaviour of the circular concrete-filled steel tube columns vol.38, pp.1, 2018, https://doi.org/10.12989/scs.2021.38.1.017
  2. Non-linear FEA of mechanical properties of modular prefabricated steel-concrete composite joints vol.40, pp.4, 2018, https://doi.org/10.12989/scs.2021.40.4.533