DOI QR코드

DOI QR Code

A Strength Analysis of Gear Train for Hydro-Mechanical Continuously Variable Transmission

  • Received : 2018.07.17
  • Accepted : 2018.08.20
  • Published : 2018.09.30

Abstract

The power train of hydro-mechanical continuously variable transmission(HMCVT) for the middle class forklift makes use of an hydro-static unit, hydraulic multi-wet disc brake & clutches and complex helical & planetary gears. The complex helical & planetary gears are a very important part of the transmission because of strength problems. The helical & planetary gears belong to the very important part of the HMCVT's power train where strength problems are the main concerns including the gear bending stress, the gear compressive stress and scoring failures. The present study, calculates specifications of the complex helical & planetary gear train and analyzes the gear bending and compressive stresses of the gears. It is necessary to analyze gear bending and compressive stresses confidently for an optimal design of the complex helical & planetary gears in respect of cost and reliability. This paper not only analyzes actual gear bending and compressive stresses of complex helical & planetary gears using Lewes & Hertz equation, but also verifies the calculated specifications of the complex helical & planetary gears by evaluating the results with the data of allowable bending and compressive stress from the Stress - No. of cycles curves of gears. In addition, this paper explains actual gear scoring and evaluates the possibility of scoring failure of complex helical & planetary gear train of hydro-mechanical continuously variable transmission for the forklift.

Keywords

References

  1. M.H. Bae, T.Y. Bae, Y.S. Cho, H.Y. Son and D.J. Kim, "The Stress Analysis of Planetary Gear System of Mixer Reducer for Concrete Mixer Truck", Journal of Drive and Control, Vol. 12 No. 4, pp. 77-81, December, 2015. https://doi.org/10.7839/ksfc.2015.12.4.077
  2. D. E. Imwalle, "Load Equalization in Planetary Gear Systems", ASME publication at the Mechanisms Conference & International Symposium on Gearing and Transmissions, pp. 232-38, 1972.
  3. D. L. Seager, "Load Sharing Among Planet Gears", SAE publication, No. 700178, pp. 651-656. 1972,
  4. F. Cunliffe, J. D. Smith and D. B. Welbourn, "Dynamic Tooth Loads in Epicyclic Gears", Transactions of the ASME Journal of Engineering for Industry, pp. 578-584, 1974.
  5. Castellani G., and V. P. Castelli, "Rating Gear Strength", ASME Paper, No. 80-C2/DET-88, pp. 37-43, 1980.
  6. Coy, J. J., D. P. Townsend, and E. V. Zaretsky, "Dynamic Capacity and Surface Fatigue Life for Spur and Helical Gears", ASME Paper, No. 75-Lub-19, pp. 56-73, 1975.
  7. Oda Satoshi and Koji Tsubokura, "Effects of Addendum Modification on Bending Fatigue Strength of Spur Gears"(3rd Report, Cast Iron and Cast Steel Gears), Bull. JSME, Vol. 24, No. 190, Paper No. 190-15, pp. 24-30, April, 1981.
  8. American Gear Manufacturers Assoc., Rating the Pitting Resistance and Bending Strength of Spur and Helical Involute Gear Teeth, AGMA Standard 218.01, pp. 14-20, 1982.
  9. D. W. Dudley, The Handbook of Practical Gear Design, 2nd Edition, Mcgraw-Hill, San Diego, pp. 1.27-1.32, 2.1-2.12, 3.1-3.45, 3.78-3.112, 1984.
  10. W. Lewes, "Investigation of the Strength of Gear Teeth", Proc. Eng. Club, Philadelphia, pp. 38-55, 1893.
  11. KIMM, Semi Auto Transmission for Small Size Forklift, RS-KIMM-2010-0038, 2011.