Steel and Composite Structures

  • 제28권6호
  • /
  • Pages.759-766
  • /
  • 2018
  • /
  • 1229-9367(pISSN)
  • /
  • 1598-6233(eISSN)
테크노프레스 (Techno-Press)
권호 표지
DOI QR코드

DOI QR Code

Residual stresses measurement in the butt joint welded metals using FSW and TIG methods

  • Taheri-Behrooz, Fathollah (School of Mechanical Engineering, Iran University of Science and Technology) ;
  • Aliha, Mohammad R.M. (Welding and Joining Research Centre, School of Industrial Engineering, Iran University of Science and Technology (IUST)) ;
  • Maroofi, Mahmood (School of Mechanical Engineering, Iran University of Science and Technology) ;
  • Hadizadeh, Vahid (School of Mechanical Engineering, Iran University of Science and Technology)
  • 투고 : 2018.03.05
  • 심사 : 2018.07.05
  • 발행 : 2018.09.25
⟨ 이전 논문 다음 논문 ⟩

초록

Friction Stir Welding (FSW) is a solid-state process, where the objects are joined together without reaching their melting point. It has been shown that this method is a suitable way to join dissimilar aluminium alloys. The current article employed hole drilling technique to measure the residual stress distribution experimentally in different zones of dissimilar aluminium alloys AA6061-T6 and AA7075-T6 Butt welded using FSW. Results are compared with those of similar AA6061-T6 plates joined using a conventional fusion welding method called tungsten inert gas (TIG). Also, the evolution of the residual stresses in the thickness direction was investigated, and it was found that the maximum residual stresses are below the yield strength of the material in the shoulder region. It was also revealed that the longitudinal residual stresses in the joint were much larger than the transverse residual stresses. Meanwhile, Vickers micro hardness measurements were performed in the cross-section of the samples. The largest hardness values were observed in the stir zone (SZ) adjacent to the advancing side whereas low hardness values were measured at the HAZ of both alloys and the SZ adjacent to the retreating side.

키워드

참고문헌

  1. Aliha, M.R.M. and Gharehbaghi, H. (2017), "The effect of combined mechanical load/welding residual stress on mixed mode fracture parameters of a thin aluminium cracked cylinder", Eng. Fract. Mech., 180, 213-228. https://doi.org/10.1016/j.engfracmech.2017.05.003
  2. Aliha, M.R.M., Shahheidari, M., Bisadi, M., Akbari, M. and Hossain, S. (2016), "Mechanical and metallurgical properties of dissimilar AA6061-T6 and AA7277-T6 joint made by FSW technique", Int. J. Adv. Manuf. Tech., 86(9-12), 2551-2565. https://doi.org/10.1007/s00170-016-8341-x
  3. Aval, H.J. (2015), "Microstructure and residual stress distributions in friction stir welding of dissimilar aluminium alloys", Mater. Des., 87, 405-413. https://doi.org/10.1016/j.matdes.2015.08.050
  4. Aval, H.J., Serajzadeh, S. and Kokabi, A.H. (2012), "Experimental and theoretical evaluations of thermal histories and residual stresses in dissimilar friction stir welding of AA5086-AA6061", Int. J. Adv. Manuf. Tech., 61(1-4), 149-160. https://doi.org/10.1007/s00170-011-3713-8
  5. Cam, G. and Mistikoglu, S. (2014), "Recent developments in friction stir welding of Al-alloys", J. Mater. Eng. Perform., 23(6), 1936-1953. https://doi.org/10.1007/s11665-014-0968-x
  6. Castro, R.A.S., Richter-Trummer, V., Tavares, S.M.O., Moreira, P.M.G., Vilaca P. and de Castro, P.M.S.T. (2011), "Friction stir welding on T-joints: residual stress evaluation", Mecanica Experim., 19, 55-65.
  7. Choi, D.H., Lee, C.Y., Ahn, B.W., Yeon, Y.M., Park, S.H.C., Sato, Y.S., Kokawa, H. and Jung, S.B. (2010), "Effect of fixed location variation in friction stir welding of steels with different carbon contents", Sci. Technol. Weld. Join., 15(4), 299-304. https://doi.org/10.1179/136217109X12577814486737
  8. Flaman, M.T., Mills, B.E. and Boag, J.M. (1987), "Analysis of stressvariation-with-depth measurement procedures for the center-hole method of residual stress measurement", Exp. Techniques, 11(6), 35-37. https://doi.org/10.1111/j.1747-1567.1987.tb00422.x
  9. Ghasemi, A.R., Taheri-Behrooz, F. and Shokrieh, M.M. (2014), "Determination of non-uniform residual stresses in laminated composites using integral hole drilling method: Experimental evaluation", J. Compos. Mater., 48(4), 415-425. https://doi.org/10.1177/0021998312473858
  10. Guo, J.F., Chen, H.C., Sun, C.N., Bi, G., Sun, Z. and Wei, J. (2014), "Friction stir welding of dissimilar materials between AA6061and AA7075 Al alloys effects of process parameters", Mater. Des., 56, 185-192. https://doi.org/10.1016/j.matdes.2013.10.082
  11. Jonckheere, C., de Meester, B., Denquin, A. and Simar, A. (2013), "Torque, temperature and hardening precipitation evolution in dissimilar friction stir welds between 6061-T6 and 2014-T6 aluminium alloys", J. Mater. Process. Technol., 213(6), 826-837. https://doi.org/10.1016/j.jmatprotec.2013.01.001
  12. Lemmen, H.J.K., Alderliesten, R.C., Pieters, R.R.G.M., Benedictus R. and Pineault, J.A. (2010), "Yield Strength and residual stress measurements on friction-stir welded aluminium alloys", J. Aircr, 47(5), 1570-1583. https://doi.org/10.2514/1.C000212
  13. Li, T., Shi, Q.Y., Li, H.K., Wang, W. and Cai, Z.P. (2008), "Residual stresses of friction stir welded 2024-T4 joints", Mater. Sci. Forum, 582, 263-266.
  14. Li, T.J., Liu, S.W. and Chan, S.L. (2015), "Cross-sectional analysis of arbitrary sections allowing for residual stresses", Steel Compos. Struct., Int. J., 18(4), 985-1000. https://doi.org/10.12989/scs.2015.18.4.985
  15. Linton, V.M. and Ripley, M.I. (2008), "Influence of time on residual stresses in friction stir welds in agehardenable 7xxx aluminium alloys", Acta Materialia, 56(16), 4319-4327. https://doi.org/10.1016/j.actamat.2008.04.059
  16. Liu, C. and Yi, X. (2013), "Residual stress measurement on AA6061-T6 aluminium alloy friction stir butt welds using contour method", Mater. Des., 46, 366-371. https://doi.org/10.1016/j.matdes.2012.10.030
  17. Miroslav, B. (2012), "Experimental investigation of residual stresses in cold formed steel sections", Steel Comp. Struct., Int. J., 2(6), 465-489.
  18. Richter-Trummer, V., Moreira, P.M.G. P. and Ribeiro, J. (2011), "The contour method for residual stress determination applied to an AA6082-T6 friction stir butt weld", Mater. Sci. Forum, 681, 1 77-188. https://doi.org/10.4028/www.scientific.net/MSF.681.177
  19. Schajer, G.S. (1981), "Application of finite element calculations to residual stress measurements", J. Eng. Mater. Technol., 103(2), 157-163. https://doi.org/10.1115/1.3224988
  20. Schajer, G.S. (1988), "Measurement of non-uniform residual stresses using the hole-drilling method", J. Eng. Mater. Technol., 110(4), 338-343. https://doi.org/10.1115/1.3226059
  21. Sedighi, M., Khandae, M. and Joudaki, J. (2011), "Calibration coefficients for residual stress measurement in incremental hole drilling method", Modares Mech. Eng., 11(1), 19-27.
  22. Shigeru, A., Tadashi, N. and Tetsumaro, H. (2004), "Reduction of residual stress for welded joint using vibrational load", Steel Comp. Struct., Int. J., 4(5), 355-365. https://doi.org/10.12989/scs.2004.4.5.355
  23. Wei, Y., Li, J., Xiong, J. and Zhang, F. (2013), "Effect of tool pin insertion depth on friction Stir lap welding of aluminium to stainless steel", J. Materi. Eng. Perform., 22(10), 3005-3009. https://doi.org/10.1007/s11665-013-0595-y
  24. Xu, W., Liu, J. and Zhu, H. (2011), "Analysis of residual stresses in thick aluminium friction stir welded butt joints", Mater. Des., 32(4), 2000-2005. https://doi.org/10.1016/j.matdes.2010.11.062
  25. Xu, W., Li, Z. and Sun, X. (2017), "Effect of welding speed on mechanical properties and the strain-hardening behavior of friction stir welded 7075 aluminium alloy joints", J. Mater. Eng. Perform., 26(4), 1938-1946. https://doi.org/10.1007/s11665-017-2618-6
  26. Zhang, Z., Zhang, Z. and Zhang, H. (2015), "Effect of residual stress of friction stir welding on the fatigue life of AA 2024-T351 joint", Proceedings of the Institution of Mechanical Engineers, Part B; Journal of Engineering Manufacture, 229(11), 2021-2034. https://doi.org/10.1177/0954405414543489
  27. Zhou, X., Mackenzie, D. and Pan, W. (2015), "A new distributed cooling method for mitigating residual stress in friction stir welding", Proceedings of the Institution of Mechanical Engineers, Part B; Journal of Engineering Manufacture. DOI: 10.1177/0954405415573849

피인용 문헌

  1. Weldability Investigation and Optimization of Process Variables for TIG-Welded Aluminium Alloy (AA 8006) vol.2021, pp.None, 2018, https://doi.org/10.1155/2021/2816338