DOI QR코드

DOI QR Code

Ambient vibration based structural evaluation of reinforced concrete building model

  • Gunaydin, Murat (Department of Civil Engineering, Karadeniz Technical University) ;
  • Adanur, Suleyman (Department of Civil Engineering, Karadeniz Technical University) ;
  • Altunisik, Ahmet C. (Department of Civil Engineering, Karadeniz Technical University)
  • 투고 : 2017.11.02
  • 심사 : 2018.08.03
  • 발행 : 2018.09.25

초록

This paper presents numerical modelling, modal testing, finite element model updating, linear and nonlinear earthquake behavior of a reinforced concrete building model. A 1/2 geometrically scale, two-storey, reinforced concrete frame model with raft base were constructed, tested and analyzed. Modal testing on the model using ambient vibrations is performed to illustrate the dynamic characteristics experimentally. Finite element model of the structure is developed by ANSYS software and dynamic characteristics such as natural frequencies, mode shapes and damping ratios are calculated numerically. The enhanced frequency domain decomposition method and the stochastic subspace identification method are used for identifying dynamic characteristics experimentally and such values are used to update the finite element models. Different parameters of the model are calibrated using manual tuning process to minimize the differences between the numerically calculated and experimentally measured dynamic characteristics. The maximum difference between the measured and numerically calculated frequencies is reduced from 28.47% to 4.75% with the model updating. To determine the effects of the finite element model updating on the earthquake behavior, linear and nonlinear earthquake analyses are performed using 1992 Erzincan earthquake record, before and after model updating. After model updating, the maximum differences in the displacements and stresses were obtained as 29% and 25% for the linear earthquake analysis and 28% and 47% for the nonlinear earthquake analysis compared with that obtained from initial earthquake results before model updating. These differences state that finite element model updating provides a significant influence on linear and especially nonlinear earthquake behavior of buildings.

키워드

과제정보

연구 과제 주관 기관 : Karadeniz Technical University

참고문헌

  1. ACI Committee 318 (2008), Building Code Requirements for Structural Concrete (ACI 318M-11) and Commentary, American Concrete Institute, Farmington Hills, MI, USA.
  2. Alampalli, S. (2000), "Effects of testing, analysis, damage, and environment on modal parameters", Mech. Syst. Signal Pr., 14(1), 63-74. https://doi.org/10.1006/mssp.1999.1271
  3. Altunisik, A.C., Bayraktar, A., Sevim, B. and Ozdemir, H. (2011), "Experimental and analytical system identification of Eynel Arch Type Steel Highway Bridge", J. Constr. Steel Res., 67(12), 1912-1921. https://doi.org/10.1016/j.jcsr.2011.06.008
  4. Altunisik, A.C., Gunaydin, M., Sevim, B., Bayraktar, A., and Adanur, S. (2015), "CFRP composite retrofitting effect on the dynamic characteristics of arch dams", Soil Dyn. Earthq. Eng., 74, 1-9. https://doi.org/10.1016/j.soildyn.2015.03.008
  5. ANSYS (2015), Swanson Analysis System, US.
  6. ANSYS(R) APDL, Release 14.5 (2015), Help System, Coupled Field Analysis Guide, ANSYS, Inc.
  7. Atamturktur, S., Hemez, F.M. and Laman, J.A. (2012), "Uncertainty quantification in model verification and validation as applied to large scale historic masonry monuments", Eng. Struct., 43, 221-234. https://doi.org/10.1016/j.engstruct.2012.05.027
  8. Bendat, J.S. and Piersol, A.G. (2004), Random Data: Analysis and Measurement Procedures, John Wiley and Sons, USA.
  9. Bonfiglioli, B. and Pascale, G. (2006), "Dynamic assessment of reinforced concrete beams repaired with externally bonded frp sheets", Mech. Compos. Mater., 42(1), 1-12. https://doi.org/10.1007/s11029-006-0012-9
  10. Brownjohn, J.M.W. (1997), "Vibration characteristics of a suspension footbridge", J. Sound Vib., 202, 29-46. https://doi.org/10.1006/jsvi.1996.0789
  11. Brownjohn, J.M.W., Dumanoğlu, A.A. and Severn, R.T. (1992), "Ambient vibration survey of the Fatih Sultan Mehmet (Second Bosporus) suspension bridge", Earthq. Eng. Struct. Dyn., 21, 907-924. https://doi.org/10.1002/eqe.4290211005
  12. Cantero, D., Hester, D., and Brownjohn, J. (2017), "Evolution of bridge frequencies and modes of vibration during truck passage", Eng. Struct., 152, 452-464. https://doi.org/10.1016/j.engstruct.2017.09.039
  13. Chang, C.C., Chang, T.Y.P. and Zhang, Q.W. (2001), "Ambient vibration of long-span cable-stayed bridge", ASCE J. Bridge Eng., 1, 46-53.
  14. Chen, G.W., Omenzetter, P. and Beskhroun, S. (2017), "Operational modal analysis of an eleven-span concrete bridge subjected to weak ambient excitations", Eng. Struct., 151, 839-860. https://doi.org/10.1016/j.engstruct.2017.08.066
  15. Deinum, P.J., Dungar, R., Ellis, B.R., Jeary, A.P., Reed, G.A.L. and Severn, R.T. (1982), "Vibration tests on Emosson arch dam in Switzerland", Earthq. Eng. Struct. Dyn., 10(3), 447-70. https://doi.org/10.1002/eqe.4290100308
  16. Diaferio, M., Foti, D. and Potenza, F. (2018), "Prediction of the fundamental frequencies and modal shapes of historic masonry towers by empirical equations based on experimental data", Eng. Struct., 156, 433-442. https://doi.org/10.1016/j.engstruct.2017.11.061
  17. Doebling, S.W., Farrar, C.R., Prime, M.B. and Shevitz, D.W. (1996), "Damage identification and health monitoring of structural and mechanical systems from changes in their vibration characteristics: A literature review", Research Rep. No. LA-13070-MS, ESA-EA, Los Alamos National Laboratory, Los Alamos, N.M.
  18. Doran, B., Koksal, H.A., Polat, Z. and Karakoc, C. (1998), "The use of "Drucker-Prager Criterion" in the analysis of reinforced concrete members by finite elements", Turkish Chamb. Civil Eng., 9(2), 1616-1625.
  19. Drucker, D.C. and Prager, W. (1952), "Soil mechanics and plastic analysis or limit design", Quart. Appl. Math., 10, 157-165. https://doi.org/10.1090/qam/48291
  20. Ewins, D.J. (1984), Modal Testing: Theory and Practice, Research Studies Press Ltd, Baldock, Hertfordshire, England.
  21. Felber, A.J. (1993), "Development of hybrid bridge evaluation system", PhD Thesis, University of British Columbia, Vancouver, Canada.
  22. Friswell, M.I. and Mottershead, J.E. (1995), Finite Element Model Updating in Structural Dynamics, Kluwer Academic, Dordrecht, The Netherlands.
  23. Hassiotis, S. and Jeong, G.D. (1995), "Identification of stiffness reductions using natural frequencies", J. Eng. Mech., ASCE, 121, 1106-1113. https://doi.org/10.1061/(ASCE)0733-9399(1995)121:10(1106)
  24. Jacobsen, N.J., Andersen, P. and Brincker, R. (2006), "Using enhanced frequency domain decomposition as a robust technique to harmonic excitation in Operational Modal Analysis", Proceedings of ISMA2006: International Conference on Noise & Vibration Engineering, Leuven, Belgium.
  25. Jaishi, B. and Ren, W.X. (2005), "Structural finite element model updating using ambient vibration test results", J. Struct. Eng., 131(4), 617-628. https://doi.org/10.1061/(ASCE)0733-9445(2005)131:4(617)
  26. Jaishi, B., Kim, H.J., Kim, M.K., Ren, W.X. and Lee, S.H. (2007), "Finite element model updating of concrete-filled steel tubular arch bridge under operational condition using modal flexibility", Mech. Syst. Signal Pr., 21, 2406-2426. https://doi.org/10.1016/j.ymssp.2007.01.003
  27. Kaiser, H. and Karbhari, V.M. (2004), "Non-destructive testing techniques for FRP rehabilitated concrete. I. A critical review", Int. J. Mater. Prod. Technol., 21(5), 349-384. https://doi.org/10.1504/IJMPT.2004.004996
  28. Kazaz, I. (2010), "Dynamic characteristics and performance assessment of reinforced concrete structural walls", PhD Thesis, Middle East Technical University, Turkey.
  29. Kouris, L.A.S., Penna, A. and Magenes, G. (2017), "Seismic damage diagnosis of a masonry building using short-term damping measurements", J. Sound Vib., 394 366-391. https://doi.org/10.1016/j.jsv.2017.02.001
  30. Loh, C.H. and Wu, T.S. (1996), "Identification of Fei-Tsui arch dam from both ambient and seismic response data", Soil Dyn. Earthq. Eng., 15, 465-483. https://doi.org/10.1016/0267-7261(96)00016-4
  31. Lubliner, J., Oliver, J., Ollers, S. and Onate, E. (1989), "A plasticdamage model for concrete", Int. J. Solid Struct., 25(3), 299-326. https://doi.org/10.1016/0020-7683(89)90050-4
  32. Oliveira, S. and Mendes P. (2006), "Development of a Cibril Dam finite element model for dynamic analysis using ambient vibration tests results", Proceedings of the III European Conference on Computational Mechanics Solids, Structures and Coupled Problems in Engineering, Lisbon, Portugal, June.
  33. OMA (2006), Operational Modal Analysis, Release 4.0, Structural Vibration Solutions A/S, Denmark.
  34. Park, H.S. and Oh, B.K. (2018), "Damage detection of building structures under ambient excitation through the analysis of the relationship between the modal participation ratio and story stiffness", J. Sound Vib., 418, 122-143. https://doi.org/10.1016/j.jsv.2017.12.036
  35. PEER (2012), Pacific Earthquake Engineering Research Centre, http://peer.berkeley.edu/smcat/data, 11.06.2012.
  36. Peeters, B. (2000), "System identification and damage detection in civil engineering", PhD Thesis, K.U, Leuven, Belgium.
  37. Proulx, J., Paultre, P., Rheault, J. and Robert, Y. (2001), "An experimental investigation of water level effects on the dynamic behavior of a large arch dam", Earthq. Eng. Struct. Dyn., 30(8), 1147-1166. https://doi.org/10.1002/eqe.55
  38. PULSE (2006), Analyzers and Solutions, Release 11.2, Bruel and Kjaer, Sound and Vibration Measurement A/S, Denmark.
  39. Rainieri, C., Fabbrocino, G., Cosenza, E. and Manfredi, G. (2007), "Implementation of OMA procedures using labview: theory and application", 2nd International Operational Modal Analysis Conference, Copenhagen, Denmark, April-May.
  40. Ren, W.X. and De Roeck, G. (2002a), "Structural damage identification using modal data. I: Simulation verification", J. Struct. Eng., 128(1), 87-95. https://doi.org/10.1061/(ASCE)0733-9445(2002)128:1(87)
  41. Ren, W.X. and De Roeck, G. (2002b), "Structural damage identification using modal data. II: Test verification", J. Struct. Eng., 128(1), 96-104. https://doi.org/10.1061/(ASCE)0733-9445(2002)128:1(96)
  42. Ren, W.X., Zhao, T. and Harik, I.E. (2004), "Experimental and analytical modal analysis of steel arch bridge", J. Struct. Eng., ASCE, 130(7), 1022-1031. https://doi.org/10.1061/(ASCE)0733-9445(2004)130:7(1022)
  43. Ribeiro, D., Calçada, R., Delgado, R., Brehm, M. and Zabel, V. (2012), "Finite element model updating of a bowstring-arch railway bridge based on experimental modal parameters", Eng. Struct., 40, 413-435. https://doi.org/10.1016/j.engstruct.2012.03.013
  44. Sevim, B., Bayraktar, A. and Altunisik, A.C. (2011), "Finite element model calibration of Berke arch dam using operational modal testing", J. Vib. Control, 17(7), 1065-1079. https://doi.org/10.1177/1077546310377912
  45. Skolnik, D., Yu, E., Wallace, J. and Taciroglu, E. (2007), "Modal system identification and finite element model updating of a 15-story building using earthquake and ambient vibration data", SEI2007, Structural Engineering Institute, California, USA, May.
  46. Sortis, A.D., Antonacci, E. and Vestroni, F. (2005), "Dynamic identification of a masonry building using forced vibration tests", Eng. Struct., 27, 155-165. https://doi.org/10.1016/j.engstruct.2004.08.012
  47. TS 500 (2000), Turkish Standart, Requirements for Design and Construction of Reinforced Concrete Structures, Turkey.
  48. Türker, T. and Bayraktar, A. (2014), "Evaluation of damage effects on dynamic characteristics of RC buildings by ambient vibration test", J. Test. Eval., 42(2), 398-411. https://doi.org/10.1520/JTE20130007
  49. Ventura, C.E., Lord, J.F. and Simpson, R.D. (2002), "Effective use of ambient vibration measurements for model updating of a 48 storey building in Vancouver, Canada", International Conference on Structural Dynamics Modelling-Test, Analysis, Correlation and Validation, Instituto de Engenharia Mecanica, Madeira Island, Portugal.
  50. Wang, B.S. and He, Z.C. (2007), "Crack detection of arch dam using statistical neural network based on the reductions of natural frequencies", J. Sound Vib., 302, 1037-1047. https://doi.org/10.1016/j.jsv.2007.01.008
  51. Willam, K.J. and Warnke, E.D. (1975), "Constitutive model for the triaxial behavior of concrete", Intl. Assoc. Bridge Struct. Eng., 19, 174-203.
  52. Wu, J.R. and Li, Q.S. (2004), "Finite element model updating for a high-rise structure based on ambient vibration measurements", Eng. Struct., 26, 979-990. https://doi.org/10.1016/j.engstruct.2004.03.002
  53. Yang, J., Jin, F., Wang, J.T. and Kou, L.H. (2017), "System identification and modal analysis of an arch dam based on earthquake response records", Soil Dyn. Earthq. Eng., 92, 109-121. https://doi.org/10.1016/j.soildyn.2016.09.039
  54. Zhou, X.T., Ko, J.M. and Ni, Y.Q. (2007), "Experimental study on identification of stiffness change in a concrete frame experiencing damage and retrofit", Struct. Eng. Mech., 25(1), 39-52. https://doi.org/10.12989/sem.2007.25.1.039
  55. Ziyad, D. (1988), "Experimental and finite element studies of a large arch dams", Ph.D. Thesis, California Institute of Technology, USA.
  56. Zonta, D., Elgamal, A., Fraser, M. and Nigel Priestley, M.J. (2008), "Analysis of change in dynamic properties of a frameresistant test building", Eng. Struct., 30, 183-196. https://doi.org/10.1016/j.engstruct.2007.02.022

피인용 문헌

  1. Nonlinear Dynamic Response of a RC Frame for Different Structural Conditions Including the Effect of FE Model Updating vol.18, pp.5, 2018, https://doi.org/10.1007/s40999-019-00483-6
  2. Response surface-based model updating to detect damage on reduced-scale masonry arch bridge vol.79, pp.1, 2021, https://doi.org/10.12989/sem.2021.79.1.009