DOI QR코드

DOI QR Code

An Analysis of Factors Influencing Insulation Performance of Inorganic Autoclaved Lightweight Concrete Sandwich Wall Panels Using Shear Connectors

전단연결재를 적용한 무기계 경량기포콘크리트(ALC) 샌드위치 외벽 패널의 단열성능에 미치는 영향요인 분석

  • 강동화 (서울시립대 대학원 건축공학과) ;
  • 강동화 (서울시립대 건축학부) ;
  • 신동현 (서울시립대 대학원 건축공학과) ;
  • 김형준 (서울시립대 건축학부)
  • Received : 2017.08.22
  • Accepted : 2017.11.18
  • Published : 2018.01.30

Abstract

The purpose of this study was to analyze factors influencing insulation performance of inorganic Autoclaved Lightweight Concrete(ALC) sandwich wall panels with the application of shear connectors. To analyze the effect of shear connectors on the thermal performance of sandwich wall panels, heat transfer analysis was conducted by using the three-dimensional heat transfer simulation software. Four types of shear connector such as Pin, Clip, Grid, and Truss were selected for insulation performance analysis. Thermal bridge coefficient was calculated by varying typical panel thickness and shear connector thickness and materials such as steel, aluminum, and stainless steel. The results showed that Grid and Truss type widely distributed along the section of sandwich wall panel had a great influence on the thermal bridge coefficient by changing the influence factors. Based on the results of thermal and structural performance analysis, effective heat transmission coefficient of the sandwich wall panel satisfying the passive house insulation criteria was calculated. As a result, it was found that heat transmission coefficient was increased from $0.132W/m^2{\cdot}K$ to $0.141{\sim}0.306W/m^2{\cdot}K$ depending on the shear connector types and materials. In the majority of cases, the passive house insulation criteria was not satisfied after using shear connectors. The results of this study were likely to vary according to how influence factors were set, but it is important to apply the methods that reduce the thermal bridge when there would be a possibility of greatly affecting the insulation performance.

Keywords

Acknowledgement

Supported by : 산업기술평가관리원(KEIT)

References

  1. Choi, I., Kim, J., & You, Y. C. (2016). Effect of cyclic loading on composite behavior of insulated concrete sandwich wall panels with GFRP shear connector. Composites Part B: Engineering, 96, 7-19. https://doi.org/10.1016/j.compositesb.2016.04.030
  2. Junes, A., & Larbi, A. S. (2016). An experimental and theoretical study of sandwich panels with TRC facings: Use of metallic connectors and TRC stiffeners. Engineering Structures, 113, 174-185. https://doi.org/10.1016/j.engstruct.2016.01.042
  3. Kim, Y. J., & Allard, A. (2014). Thermal response of precast concrete sandwich walls with various steel connectors for architectural buildings in cold regions. Energy and Buildings, 80, 137-148. https://doi.org/10.1016/j.enbuild.2014.05.022
  4. Lim, D., Kim, J. Kim, Y., Kim, T., & Lee, S. (2007). A Study on the Thermal Performance of Envelope according to the Objective for Heating Load Reduction in Apartment Houses, Proceedings of Annual Conference of the Architectural Institute of Korea, 27(1), 881-884.
  5. Ministry of Land, Transport and Maritime Affairs (MLTM). (2010). NO.2010-371 The Code for Energy-efficient Building Design.
  6. Ministry of Land, Infrastructure and Transport (MOLIT). (2013). NO.2013-149 The Code for Energy-efficient Building Design.
  7. Ministry of Land, Infrastructure and Transport (MOLIT). (2015). NO.2015-1108 The Code for Energy-efficient Building Design.
  8. Naito, C. J., Hoemann, J. M., Bewick, B. T., & Hammons, M. I. (2009). Evaluation of shear tie connectors for use in insulated concrete sandwich panels. Lehigh University Bethlehem, PA, Department of Civil and Environmental Engineering.
  9. PCI Committee. (2011). State of the Art of Precast/Prestressed Concrete Sandwich Wall Panels. PCI Journal, 56, 131-176.
  10. Song, J., Park, M., Lim, J., & Song, S. (2015). Energy, Condensation Risk and Constructability Evaluation of Metal-Exterior Curtain Wall Panel Systems for Reducing Heat Loss through Thermal Bridges, Journal of the Architectural Institute of Korea, Planning and Design Section, 31(2), 283-293. https://doi.org/10.5659/JAIK_PD.2015.31.2.283
  11. The International Organization for Standardization (ISO), (2007), Thermal Bridges in Building Construction-Heat Flows and Surface Temperatures-Detailed Calculations, The International Organization for Standardization (ISO): Geneva, Switzerland.
  12. Theodosiou, T. G., Tsikaloudaki, A. G., Kontoleon, K. J., & Bikas, D. K. (2015). Thermal bridging analysis on cladding systems for building facades. Energy and Buildings, 109, 377-384. https://doi.org/10.1016/j.enbuild.2015.10.037