DOI QR코드

DOI QR Code

Creep characteristics and instability analysis of concrete specimens with horizontal holes

  • Xin, Yajun (School of Energy Science and Engineering, Henan Polytechnic University) ;
  • Hao, Haichun (School of Energy Science and Engineering, Henan Polytechnic University) ;
  • Lv, Xin (School of Energy Science and Engineering, Henan Polytechnic University) ;
  • Ji, Hongying (Institute of Resource and Environment, Henan Polytechnic University)
  • 투고 : 2018.07.21
  • 심사 : 2018.12.15
  • 발행 : 2018.12.25

초록

Uniaxial compressive strength test and uniaxial compression creep one were produced on four groups of twelve concrete specimens with different hole number by RLW-2000 rock triaxial rheology test system. The relationships between horizontal holes and instantaneous failure stress, the strain, and creep failure stress, the strain, and the relationships between stress level and instantaneous strain, creep strain were studied, and the relationship between horizontal holes and failure mode was determined. The results showed that: with horizontal hole number increasing, compressive strength of the specimens decreased whereas its peak strain increased, while both creep failure strength and its peak strain decreased. The relationships between horizontal holes and compressive strength of the specimens, the peak strain, were represented in quadratic polynomial, the relationships between horizontal holes and creep failure strength, the peak strain were represented in both linear and quadratic polynomial, respectively. Instantaneous strain decreased with stress level increasing, and the more holes in the blocks the less the damping of instantaneous strain were recorded. In the failure stress level, instantaneous strain reversally increased, creep strain showed three stages: decreasing, increasing, and sharp increasing; in same stress level, the less holes the less creep strain rate was recorded. The compressive-shear failure was produced along specimen diagonal line where the master surface of creep failure occurred, the more holes in a block, the higher chances of specimen failure and the more obvious master surface were.

키워드

과제정보

연구 과제 주관 기관 : Henan Polytechnic University

참고문헌

  1. Andre, F.A., Micael, M.I., Valter, J.L. and Antonio, P. (2016), "Punching behaviour of RC flat slabs under reversed horizontal cyclic loading", Eng. Struct., 117(15), 204-219. https://doi.org/10.1016/j.engstruct.2016.03.007
  2. Bauchkar, S.D. and Chore, H.S. (2018), "Experimental study on rheology, strength and durability properties of high strength self-compacting concrete", Comput. Concrete, 22(2), 183-196. https://doi.org/10.12989/CAC.2018.22.2.183
  3. Brantut, N., Heap, M.J., Meredith, P.G. and Baud, P. (2013), "Time-dependent cracking and brittle creep in crustal rocks: A review", J. Struct. Geol., 52, 17-43. https://doi.org/10.1016/j.jsg.2013.03.007
  4. Brijes, M. and Priyesh, V. (2015), "Uniaxial and triaxial single and multistage creep tests on coal-measure shale rocks", Int. J. Coal Geol., 137, 55-65. https://doi.org/10.1016/j.coal.2014.11.005
  5. Du, M.R., Jing, H.W., Su, H.J., Zhu, T.T. and Chen, M.L. (2017), "Strength and failure characteristics of sandstone containing two circular holes filled with two types of inclusions under uniaxial compression", J. Cent. South Univ., 24(11), 2487-2495. https://doi.org/10.1007/s11771-017-3661-z
  6. Emara, M., Torres, L., Baena, M., Bards, C. and Moawad, M. (2017), "Effect of sustained loading and environmental conditions on the creep behavior of an epoxy adhesive for concrete structures strengthened with CFRP laminates", Compos. Part B-Eng., 129, 88-96. https://doi.org/10.1016/j.compositesb.2017.07.026
  7. Emara, M., Torres, L., Baena, M., Barris, C. and Cahis, X. (2018), "Bond response of NSM CFRP strips in concrete under sustained loading and different temperature and humidity conditions", Compos. Struct., 192, 1-7. https://doi.org/10.1016/j.compstruct.2018.02.048
  8. Firme, P., Roehl, D. and Romanel, C. (2016), "An assessment of the creep behaviour of Brazilian salt rocks using the multimechanism deformation model", Acta Geotechnica, 11(06), 1445-1463. https://doi.org/10.1007/s11440-016-0451-y
  9. Haeri, H. and Sarfarazi, V. (2016), "The effect of micro pore on the characteristics of crack tip plastic zone in concrete", Comput. Concrete, 17(1), 107-127. https://doi.org/10.12989/CAC.2016.17.1.107
  10. Haeri, H., Khaloo, A. and Marji, M.F. (2015), "Fracture analyses of different pre-holed concrete specimens under compression", Acta Mech. Snica-prc., 31(6), 855-870. https://doi.org/10.1007/s10409-015-0436-3
  11. Han, G.S., Jing, H.W., Su, H.J., Zhu, T.T., Du, M.R. and Xiong, F. (2017), "Experimental study on compressive strength and fracture characteristics of sandstone containing double circular cavities", J. China Coal Soc., 42(04), 871-878.
  12. Hodhod, O.A., Said, T.E. and Ataya, A.M. (2018), "Prediction of creep in concrete using genetic programming hybridized with ANN", Comput. Concrete, 21(5), 513-523. https://doi.org/10.12989/CAC.2018.21.5.513
  13. Janusz, K., Zvonko, T. and Slobodan, Z. (2016), "The soft rock socketed monopile with creep effects-a reliability approach based on wavelet neural networks", Arch. Min. Sci., 61(3), 571-585. https://doi.org/10.1515/amsc-2016-0041
  14. Kamran, P., Aliakbar, G. and Takato, T. (2015), "Rock failure assessment based on crack density and anisotropy index variations during triaxial loading tests", Geomech. Eng., 9(6), 793-813. https://doi.org/10.12989/GAE.2015.9.6.793
  15. Klovanych, S. (2015), "Creep of concrete at variable stresses and heating", Comput. Concrete, 16(6), 897-907. https://doi.org/10.12989/CAC.2015.16.6.897
  16. Li, D.Y., Li, X.B., Li, C.L. and Wang, Y.Y. (2011), "Experimental and numerical studies of mechanical response of plate-shape granite samples containing prefabricated holes under uniaxial compression", Chin. J. Rock Mech. Eng., 30(06), 1198-1206.
  17. Li, F., Zhang, Y.G., Liu, J.R., Zhang, L. and Fang, S.H. (2016), "The dynamical response characteristics of elastic-plastic coal under dynamic load", J. Nat. Gas. Sci. Eng., 29, 497-505. https://doi.org/10.1016/j.jngse.2016.01.032
  18. Li, X.B., Weng, L., Xie, X.F. and Wu, Q.H. (2015), "Study on the degradation of hard rock with a pre-existing opening under static-dynamic loadings using nuclear magnetic resonance technique", Chin. J. Rock Mech. Eng., 34(10), 1985-1993.
  19. Li, X.Z. and Shao, Z.S. (2016a), "Investigation of macroscopic brittle creep failure caused by microcrack growth under step loading and unloading in rocks", Rock Mech. Rock Eng., 49(7), 2581-2593. https://doi.org/10.1007/s00603-016-0953-9
  20. Li, X.Z. and Shao, Z.S. (2016b), "Micro-macro modeling of brittle creep and progressive failure subjected to compressive loading in rock", Environ. Earth Sci., 75(7), 583. https://doi.org/10.1007/s12665-016-5365-3
  21. Liu, Z.W. and Li, Y.H. (2010), "Experimental investigation on the deformation and crack behavior of rock specimen with a hole undergoing uniaxial compressive load", Eng. Mech., 27(8), 133-139.
  22. Ma, S.P., Wang, L.G. and Zhao, Y.H. (2006), "Experimental study on deformation field evolution during failure procedure of a rock borehole structure", Rock Soil Mech., 27(7), 1082-1086. https://doi.org/10.3969/j.issn.1000-7598.2006.07.012
  23. Mazloom, M., Homayooni, S.M. and Miri, S.M. (2018), "Effect of rock flour type on rheology and strength of self-compacting lightweight concrete", Comput. Concrete, 21(2), 199-207. https://doi.org/10.12989/CAC.2018.21.2.199
  24. Moon, K.H. (2001), "Creep characteristics of rocks and concrete -a comparison", Tunn. Undergr. Sp. Tech., 3(2), 33-56.
  25. O mer, A., Takashi, I., Ugur, O ., Kwasniewski, M., Shariar, K., Okuno, T., Ozgenoglu, A., Malan, D.F. and Okada, T. (2014), "ISRM suggested methods for determining the creep characteristics of rock", Rock Mech. Rock Eng., 47(1), 275-290. https://doi.org/10.1007/s00603-013-0520-6
  26. Rahimi, S. and Hosseini, M. (2015), "Laboratory studies of creep behavior on thick-walled hollow cylindrical salt rock specimens", Arab. J. Geosci., 8(8), 5949-5957. https://doi.org/10.1007/s12517-014-1622-5
  27. Reiko, K. and Richard, J.J. (2002), "On measuring creep behaviour in granular materials through triaxial testing", Can. Geotech. J., 39(5), 1061-1074. https://doi.org/10.1139/t02-059
  28. Shokrieh, M.M., Rezvani, S. and Mosalmani, R. (2017), "Mechanical behavior of polyester polymer concrete under low strain rate loading conditions", Polym. Test, 63, 596-604. https://doi.org/10.1016/j.polymertesting.2017.09.015
  29. Shrey, A. and Brijes, M. (2015), "Investigation of the failure mode of shale rocks in biaxial and triaxial compression tests", Int. J. Rock Mech. Min., 79, 109-123. https://doi.org/10.1016/j.ijrmms.2015.08.014
  30. Su, L., Wang, Y.F., Mei, S.Q. and Li, P.F. (2017), "Experimental investigation on the fundamental behavior of concrete creep", Constr. Build Mater., 152, 250-258. https://doi.org/10.1016/j.conbuildmat.2017.06.162
  31. Tang, H., Wang, D.P., Huang, R.Q., Pei, X.J. and Chen, W.L. (2018), "A new rock creep model based on variable-order fractional derivatives and continuum damage mechanics", B. Eng. Geol. Environ., 77(1), 375-383. https://doi.org/10.1007/s10064-016-0992-1
  32. Wang, S.H., Xu, Y., Zhang, L. and Wang, S.M. (2011), "Laboratory experiments on the process of rock tunnel failure and its particle flow numerical simulation", J. Northeast Univ., 32(4), 587-590.
  33. Wu, C.Z., Chen, Q.S., Basack, M.A., Xu, R.Q. and Shi, Z.M. (2016), "Biaxial creep test study on the influence of structural anisotropy on rheological behavior of hard rock", J. Mater. Civil Eng., 28(10), 04016104. https://doi.org/10.1061/(ASCE)MT.1943-5533.0001571
  34. Wu, C.Z., Chen, Q.S., Basack, S. and Karekal, S. (2018), "Laboratory investigation on rheological properties of greenschist considering anisotropy under multi-stage compressive creep condition", J. Struct. Geol., 114, 111-120. https://doi.org/10.1016/j.jsg.2018.06.011
  35. Wu, X.L., Wang, X.B. and Pan, Y.S. (2010), "Numerical simulation of mechanical behavior of a specimen composed of circular granular material", Hydro Sci. Eng., 125(3), 40-44.
  36. Xie, L.M., Zhu, W.C., Wang, S.H. and Niu, L.L. (2011), "Three-Dimensional parallel computing on failure process of rock specimen with a pre-existing circular opening", Chin. J. Geotech. Eng., 33(9), 1447-1455.
  37. Xin, Y.J., Li, M.Y., An, D.C., Ji, H.Y. and Kang, J.C. (2017), "Experimental study on the instability mechanism of the majordefect fractured rock", Arab. J. Geosci., 10(14), 311. https://doi.org/10.1007/s12517-017-3095-9
  38. Yang, R.H., Xu, P., Yue, Z.W. and Chen, C. (2016), "Laboratory study of interaction between a circular hole defect and mode I moving crack", Rock Soil Mech., 37(6), 1597-1602.
  39. Zhang, Y., Shao, J.F., Xu, W.Y. and Jia, Y. (2016), "Timedependent behavior of cataclastic rocks in a multi-loading triaxial creep test", Rock Mech. Rock Eng., 49(9), 3793-3803. https://doi.org/10.1007/s00603-016-0948-6
  40. Zhao, X.D., Zhang, H.X. and Zhu, W.C. (2014), "Fracture evolution around pre-existing cylindrical cavities in brittle rocks under uniaxial compression", T. Nonferr. Metal Soc., 24(3), 806-815. https://doi.org/10.1016/S1003-6326(14)63129-0
  41. Zhao, Y.L., Zhang, L.Y., Wang, W.J., Wan, W. and Ma, W.H. (2018), "Separation of elastoviscoplastic strains of rock and a nonlinear creep model", Int. J. Geomech., 18(1), 04017129. https://doi.org/10.1061/(ASCE)GM.1943-5622.0001033
  42. Zhou, J., Chen, M., Jin, Y. and Zhang, G.Q. (2008), "Analysis of fracture propagation behavior and fracture geometry using a triaxial fracturing system in naturally fractured reservoirs", Int. J. Rock Mech. Min., 45(7), 1143-1152. https://doi.org/10.1016/j.ijrmms.2008.01.001
  43. Zhou, W. and Hu, H.B. (2014), "Analysis on bearing capacity and behavior of reactive powder concrete with empty concentric duct under local pressure", Eng. Mech., 31(7), 119-128.
  44. Zhu, T.T., Jing, H.W., Su, H.J., Yi, Q. and Du, M.R. (2015), "Mechanical behavior of sandstone containing double circular cavities under uniaxial compression", Chin. J. Geotech. Eng., 37(6), 1047-1056.
  45. Zhu, W.C., Tang, C.A., Zhao, Q.L. and Zhuo, J.S. (2002), "Mechanical model and numerical simulation of fracture process of concrete", Adv. Mech., 32(4), 579-598. https://doi.org/10.3321/j.issn:1000-0992.2002.04.012