DOI QR코드

DOI QR Code

CAPP for 3D Printer with Metallic Wire Supplied from the Front

금속선재 전방공급형 3D프린터를 위한 공정계획

  • Kim, Ho-chan (Department of Mechanical and Automotive Engineering, Andong National University) ;
  • Kim, Jae-gu (Korea Institute of Machinery and Materials(KIMM))
  • 김호찬 (안동대학교 기계자동차공학과) ;
  • 김재구 (한국기계연구원)
  • Received : 2018.09.07
  • Accepted : 2018.09.17
  • Published : 2018.10.31

Abstract

The materials used for 3D printing are mainly plastic and metal. These materials are usually used in the powdered form. In order to improve the surface roughness of a manufactured product, these powders should consist of small uniform spherical particles. However, the powdered forms are sold at a considerably higher price than bulk or wired materials. When a wire-type material is used instead of a powder, we can supply a relatively large amount of the material at one time as well as reduce the cost. Moreover, the use of this form of the material will increase the process efficiency. This paper deals with the technology required to feed a wire material in front of the tool movement and discusses the examples used for the verification.

Keywords

References

  1. Shim, J. H., Yun, W. S. and Ko, T. J., “Successful Examples of 3D Printing Technology-based Start-up Enterprises,” Journal of the Korean Society of Manufacturing Process Engineers, Vol. 15, No. 2, pp. 104-110, 2016. https://doi.org/10.14775/ksmpe.2016.15.2.104
  2. Choi, J. W. and Kim, H. C., “3D Printing Technologies - A Review,” Journal of the Korean Society of Manufacturing Process Engineers, Vol. 14, No. 3, pp. 1-8, 2015. https://doi.org/10.14775/ksmpe.2015.14.3.001
  3. Wohler, T., Wohler's report 2017, Wohler Associates, 2017.
  4. Syed, W. U. H., Pinkerton, A. J., and Li, L., "A Comparative Study of Wire Feeding and Powder Feeding in Direct Diode Laser Deposition for Rapid Prototyping," Applied Surface Science, Vol. 247, Nos. 1-4, pp. 268-276, 2005. https://doi.org/10.1016/j.apsusc.2005.01.138
  5. Mok, S. H., Bi, G., Folkes, J., and Pashby, I., “Deposition of Ti-6AL-4V Using a High Power Diode Laser and Wire, Part I: Investigation on the Process Characteristics,” Surface and Coatings Technology, Vol. 202, No. 16, pp. 3933-3939, 2008. https://doi.org/10.1016/j.surfcoat.2008.02.008
  6. Abioye, T., Folkes, J., and Clare, A., “A Parametric Study of Inconel 625 Wire Laser Deposition,” Journal of Materials Processing Technology, Vol. 213, No. 12, pp. 2145-2151, 2013. https://doi.org/10.1016/j.jmatprotec.2013.06.007
  7. Hagqvist, P., Heralic, A., Christiansson, A.-K., and Lennartson, B., "Resistance Measurements for Control of Laser Metal Wire Deposition," Optics and Lasers in Engineering, Vol. 54, pp. 62-67, 2014. https://doi.org/10.1016/j.optlaseng.2013.10.010
  8. Miranda, R., Lopes, G., Quintino, L., Rodrigues, J., and Williams, S., “Rapid Prototyping with High Power Fiber Lasers,” Materials & Design, Vol. 29, No. 10, pp. 2072-2075, 2008. https://doi.org/10.1016/j.matdes.2008.03.030
  9. Kim, J. G. and Lee. C. W., “Laser Assisted Additive Manufacturing by Rotating Metal Wire Feeder,” J. Korean Soc. Precis. Eng., Vol. 35, No. 9, pp. 848, 2018.
  10. Lee, S. Y., Lee, I. K., Lee, J. W., Lee, S. B. and Lee, S. K., "Evaluation of Wear Characteristics of AISI H13 ToolSteel Repaired by Metal 3D Printing," Journal of the Korean Society of Manufacturing Process Engineers, Vol. 16, No. 4, p. 10, 2017.
  11. Olioul, I. M. and Kim, H. C., "An Algorithm for the Removing of Offset Loop Twists during the Tool Path Generation of FDM 3D Printer," Journal of the Korean Society of Manufacturing Process Engineers, Vol. 16, No. 3, p. 3, 2017.
  12. Kang, Y. G, Lee, T. W. and Shin, G. S., "The Influence of Experiment Variables on 3D Printing using ABS Resin," Journal of the Korean Society of Manufacturing Process Engineers, Vol. 16, No. 2, p. 96, 2017. https://doi.org/10.14775/ksmpe.2016.16.1.096