DOI QR코드

DOI QR Code

FDM 3D 전도성 프린팅 어닐링 조건 따른 전기적 특성 연구

Study on Electrical Characteristics of FDM Conductive 3D Printing According to Annealing Conditions

  • Lee, Sun Kon (Department of Mechanical Engineering, Inha University) ;
  • Kim, Yong Rae (Department of Mechanical Engineering, Inha University) ;
  • Yoo, Tae Jung (Department of Mechanical Engineering, Inha University) ;
  • Park, Ji Hye (Department of Mechanical Engineering, Inha University) ;
  • Kim, Joo Hyung (Department of Mechanical Engineering, Inha University)
  • 투고 : 2018.05.27
  • 심사 : 2018.08.16
  • 발행 : 2018.12.31

초록

In this paper, the effect of different 3D printing parameters including laminated angle and annealing temperature is observed their effect on FDM conductive 3D printing. In FDM 3D printing, a conductive filament is heated quickly, extruded, and then cooled rapidly. FDM 3D Print conductive filament is a poor heat conductor, it heats and cools unevenly causing the rapid heating and cooling to create internal stress. when the printed conductive specimens this internal stress can be increase electrical resistance and decrease electrical conductivity. Therefore, This experiment would like to use annealing to remove internal stress and increase electrical conductivity. The result of experiment when 3D printing conductive specimen be oven cooling of annealing temperature $120^{\circ}C$ electrical resistance appeared decrease than before annealing. So We have found that 3D printing annealing removes internal stresses and increases the electrical conductivity of printed specimens. These results are very useful for making conductive 3D printing electronic circuit, sensor ect...with electrical conductance suitable for the application.

키워드

참고문헌

  1. Choi, J. W., Kim, H. C., "3D Printing Technologies - A Review," Journal of the Korean Society of Manufacturing Process Engineers, Vol. 14, No. 3, pp. 1-8, 2015. https://doi.org/10.14775/ksmpe.2015.14.3.001
  2. Jang, J., Cho, D. W., “A Review of the Fabrication of Soft Structures with Three-dimensional Printing Technology,” Journal of the Korean Society of Manufacturing Process Engineers, Vol. 14, No. 6, pp. 142-148, 2015. https://doi.org/10.14775/ksmpe.2015.14.6.142
  3. Kim, D. B., Lee, G. T., Lee, I. H., Cho, H. Y., “Finite Element Analysis for Fracture Criterion of PolyJet Materials,” Journal of the Korean Society of Manufacturing Process Engineers, Vol. 14, No. 4, pp. 134-139, 2015. https://doi.org/10.14775/ksmpe.2015.14.4.134
  4. Lanzotti, A., Grasso, M., Staiano, G., Martorelli, M., “The impact of process parameters on mechanical properties of parts fabricated in PLA with an open-source 3-D printer,” Rapid Prototyping Journal, Vol. 21, No. 5, pp. 604-617, 2015. https://doi.org/10.1108/RPJ-09-2014-0135
  5. Hashima, K., Nishitsuji, S., Inoue, T., "Structure-properties of super-tough PLA alloy with excellent heat resistance," Polymer, Vol. 51, No. 17, pp. 3934-3939, 2010. https://doi.org/10.1016/j.polymer.2010.06.045
  6. Postiglione, Giovanni., Natale, Gabriele., Griffini, Gianmarco., Levi, Marinella., Turri, Stefano., "Conductive 3D microstructures by direct 3D printing of polymer/carbon nanotube nanocomposites via liquid deposition modeling," composites Part A, Vol. 76, pp. 110-114, 2015. https://doi.org/10.1016/j.compositesa.2015.05.014
  7. Seol, K. S., Shin, B. C., Zhang, S. U., "Fatigue Test of 3D-printed ABS Parts Fabricated by Fused Deposition Modeling," Journal of the Korean Society of Manufacturing Process Engineers, Vol. 17, No. 3, pp. 93-101, 2018. https://doi.org/10.14775/ksmpe.2018.17.3.093
  8. Lee, S. K., Kim, Y. R., Kim, S. H., Kim, J, H., “Investigation of the Internal Stress Relaxation in FDM 3D Printing : Annealing Conditions,” Journal of the Korean Society of Manufacturing Process Engineers, Vol. 17, No. 4, pp. 130-136, 2018.

피인용 문헌

  1. Optimization of Manufacturing Conditions of Pressure-Sensitive Ink Based on MWCNTs vol.18, pp.8, 2018, https://doi.org/10.14775/ksmpe.2019.18.8.001