DOI QR코드

DOI QR Code

Domain decomposition technique to simulate crack in nonlinear analysis of initially imperfect laminates

  • Ghannadpour, S. Amir M. (Faculty of New Technologies and Engineering, Shahid Beheshti University) ;
  • Karimi, Mona (Faculty of New Technologies and Engineering, Shahid Beheshti University)
  • 투고 : 2018.06.30
  • 심사 : 2018.10.23
  • 발행 : 2018.12.10

초록

In this research, an effective computational technique is carried out for nonlinear and post-buckling analyses of cracked imperfect composite plates. The laminated plates are assumed to be moderately thick so that the analysis can be carried out based on the first-order shear deformation theory. Geometric non-linearity is introduced in the way of von-Karman assumptions for the strain-displacement equations. The Ritz technique is applied using Legendre polynomials for the primary variable approximations. The crack is modeled by partitioning the entire domain of the plates into several sub-plates and therefore the plate decomposition technique is implemented in this research. The penalty technique is used for imposing the interface continuity between the sub-plates. Different out-of-plane essential boundary conditions such as clamp, simply support or free conditions will be assumed in this research by defining the relevant displacement functions. For in-plane boundary conditions, lateral expansions of the unloaded edges are completely free while the loaded edges are assumed to move straight but restricted to move laterally. With the formulation presented here, the plates can be subjected to biaxial compressive loads, therefore a sensitivity analysis is performed with respect to the applied load direction, along the parallel or perpendicular to the crack axis. The integrals of potential energy are numerically computed using Gauss-Lobatto quadrature formulas to get adequate accuracy. Then, the obtained non-linear system of equations is solved by the Newton-Raphson method. Finally, the results are presented to show the influence of crack length, various locations of crack, load direction, boundary conditions and different values of initial imperfection on nonlinear and post-buckling behavior of laminates.

키워드

참고문헌

  1. Alinia, M.M., Hosseinzadeh, S.A.A. and Habashi, H.R. (2007), "Influence of central cracks on buckling and post-buckling behaviour of shear panels", Thin-Wall. Struct., 45, 422-431. https://doi.org/10.1016/j.tws.2007.03.003
  2. Batra, R.C. and Ching, H.K. (2002), "Analysis of Elastodynamic deformations near a crack/notch tip by meshless local Petrov-Galarkin (MLPG) method", Comput. Model. Eng. Sci., 3(6), 717-730.
  3. Cao, Z. and Liu, Y. (2012), "A new numerical modeling for evaluating the stress intensity factors in 3-D fracture analysis", Struct. Eng. Mech., 43(3), 321-336. https://doi.org/10.12989/sem.2012.43.3.321
  4. Cetkovic, M. and Vuksanovic, D. (2011), "Large deflection analysis of laminated composite plates using layerwise displacement model", Struct. Eng. Mech., 40(2), 257-277. https://doi.org/10.12989/sem.2011.40.2.257
  5. Chia, C.Y. (1988), "Geometrically nonlinear behavior of composite plates: A review", Appl. Mech. Rev., 41(12), 439-451. https://doi.org/10.1115/1.3151873
  6. Dimitri, R., Fantuzzi, N., Yong, L. and Tornabene, F. (2017), "Numerical computation of the crack development and SIF in composite materials with XFEM and SFEM", Compos. Struct., 160, 468-490. https://doi.org/10.1016/j.compstruct.2016.10.067
  7. Fantuzzi, N., Tornabene, F. and Viola, E. (2016), "Four-parameter functionally graded cracked plates of arbitrary shape: A GDQFEM solution for free vibrations", Mech. Adv. Mater. Struct., 23(1), 89-107. https://doi.org/10.1080/15376494.2014.933992
  8. Ghannadpour, S.A.M., Kurkaani Barvaj, A. and Tornabene, F. (2018), "A semi-analytical investigation on geometric nonlinear and progressive damage behavior of relatively thick laminated plates under lateral pressure and end-shortening", Compos. Struct., 194, 598-610. https://doi.org/10.1016/j.compstruct.2018.04.011
  9. Ghannadpour, S.A.M., Ovesy, H.R. and Zia-Dehkordi, E. (2015), "Buckling and post-buckling behaviour of moderately thick plates using an exact finite strip", Comput. Struct., 147, 172-180. https://doi.org/10.1016/j.compstruc.2014.09.013
  10. Kandasamy, R., Dimitri, R. and Tornabene, F. (2016), "Numerical study on the free vibration and thermal buckling behavior of moderately thick functionally graded structures in thermal environments", Compos. Struct., 157, 207-221. https://doi.org/10.1016/j.compstruct.2016.08.037
  11. Kar, V.R. and Panda, S.K. (2016), "Post-buckling behaviour of shear deformable functionally graded curved shell panel under edge compression", Int. J. Mech. Sci., 115, 318-324.
  12. Kar, V.R. and Panda, S.K. (2017), "Postbuckling analysis of shear deformable FG shallow spherical shell panel under nonuniform thermal environment", J. Therm. Stress., 40(1), 25-39. https://doi.org/10.1080/01495739.2016.1207118
  13. Kar, V.R., Mahapatra, T.R. and Panda, S.K. (2017), "Effect of different temperature load on thermal postbuckling behavior of functionally graded shallow curved shell panels", Compos. Struct., 160, 1236-1247. https://doi.org/10.1016/j.compstruct.2016.10.125
  14. Kar, V.R., Panda, S.K. and Mahapatra, T.R. (2016), "Thermal buckling behavior of shear deformable functionally graded single/doubly curved shell panel with TD and TID properties", Adv. Mater. Res., 5(4), 205-221. https://doi.org/10.12989/AMR.2016.5.4.205
  15. Katariya, P.V and Panda, S.K. (2016), "Thermal buckling and vibration analysis of laminated composite curved shell panel", Aircr. Eng. Aerosp. Technol., 88(1), 97-107. https://doi.org/10.1108/AEAT-11-2013-0202
  16. Katariya, P.V., Das, A. and Panda, S.K. (2018), "Buckling analysis of SMA bonded sandwich structure-using FEM", IOP Confer. Ser.: Mater. Sci. Eng., 338(1), 012035.
  17. Katariya, P.V., Panda, S.K. and Mohapatra, T.R. (2017b), "Nonlinear thermal buckling behaviour of laminated composite panel structure including the stretching effect and higher-order finite element", Adv. Mater. Res., 6(4), 349-361. https://doi.org/10.12989/AMR.2017.6.4.349
  18. Katariya, P.V., Panda, S.K., Hirwani, C.K., Mehar, K. and Thakara, O. (2017a), "Enhancement of thermal buckling strength of laminated sandwich composite panel structure embedded with shape memory alloy fibre", Smart Struct. Syst., 20(5), 595-607. https://doi.org/10.12989/SSS.2017.20.5.595
  19. Kress, R. and Lee, K.M. (2003), "Integral equation methods for scattering from an impedance crack", Comput. Appl. Math., 161, 161-177. https://doi.org/10.1016/S0377-0427(03)00586-7
  20. Leissa, A.W. (1987), "A review of laminated composite plate buckling", Appl. Mech. Rev., 40, 575-591. https://doi.org/10.1115/1.3149534
  21. Liu, Y. and Shu, D.W. (2015), "Effects of edge crack on vibration characteristics of delaminated beam", Struct. Eng. Mech., 53(4), 767-780. https://doi.org/10.12989/SEM.2015.53.4.767
  22. Milazzo, A. and Oliveri, V. (2015), "Post-buckling analysis of cracked multilayered composite plates by pb-2Rayleigh-Ritz method", Compos. Struct., 132, 75-86. https://doi.org/10.1016/j.compstruct.2015.05.007
  23. Milazzo, A. and Oliveri, V. (2017), "Buckling and post-buckling of stiffened composite panels with cracks and delaminations by ritz approach", AIAA J., 55, 965-980. https://doi.org/10.2514/1.J055159
  24. Monfared, M.M. (2017), "Mode III SIFs for interface cracks in an FGM coating-substrate system", Struct. Eng. Mech., 64(1), 71-79. https://doi.org/10.12989/sem.2017.64.1.071
  25. Nasirmanesh, A. and Mohammadi, S. (2015), "XFEM buckling analysis of cracked composite plates", Compos. Struct., 131, 333-343. https://doi.org/10.1016/j.compstruct.2015.05.013
  26. Ovesy, H.R. and Ghannadpour, S.A.M. (2009), "An exact finite strip for calculation of relative post-buckling stiffness of isotropic plates", Struct. Eng. Mech., 31(2), 181-210. https://doi.org/10.12989/sem.2009.31.2.181
  27. Ovesy, H.R. and Ghannadpour, S.A.M. (2011), "An exact finite strip for the initial postbuckling analysis of channel section struts", Comput. Struct., 89(19), 1785-1796. https://doi.org/10.1016/j.compstruc.2010.10.009
  28. Ovesy, H.R., Zia-Dehkordi, E. and Ghannadpour, S.A.M. (2016), "High accuracy post-buckling analysis of moderately thick composite plates using an exact finite strip", Comput. Struct., 174, 104-112. https://doi.org/10.1016/j.compstruc.2015.09.014
  29. Panda, S.K. and Ramachanda, L. (2011), "Buckling and post-buckling behavior of cross-ply composite plate subjected to non-uniform in-plane loads", J. Eng. Mech., 137(9), 589-597. https://doi.org/10.1061/(ASCE)EM.1943-7889.0000258
  30. Panda, S.K., and Katariya, P.V. (2015), "Stability and free vibration behavior of laminated composite panels under thermo-mechanical loading", Int. J. Appl. Comput. Math., 1(3), 475-490. https://doi.org/10.1007/s40819-015-0035-9
  31. Panda, S.K. and Singh, B.N. (2009), "Thermal postbuckling behavior of laminated composite cylindrical/hyperboloid shallow shell panel using nonlinear finite element method", Compos. Struct., 91(3), 366-374. https://doi.org/10.1016/j.compstruct.2009.06.004
  32. Panda, S.K. and Singh, B.N. (2010a), "Nonlinear free vibration analysis of thermally post-buckled composite spherical shell panel", Int. J. Mech. Mater. Des., 6(2), 175-188. https://doi.org/10.1007/s10999-010-9127-1
  33. Panda, S.K. and Singh, B.N. (2010b), "Thermal post-buckling analysis of a laminated composite spherical shell panel embedded with shape memory alloy fibres using non-linear finite element method", J. Mech. Eng. Sci., 224(4), 757-769. https://doi.org/10.1243/09544062JMES1809
  34. Panda, S.K. and Singh, B.N. (2011), "Large amplitude free vibration analysis of thermally post-buckled composite doubly curved panel using nonlinear FEM", Fin. Elem. Analy. Des., 47(4), 378-386. https://doi.org/10.1016/j.finel.2010.12.008
  35. Panda, S.K. and Singh, B.N. (2013a), "Nonlinear finite element analysis of thermal post-buckling vibration of laminated composite shell panel embedded with SMA fibre", Aerosp. Sci. Technol., 29(1), 47-57. https://doi.org/10.1016/j.ast.2013.01.007
  36. Panda, S.K. and Singh, B.N. (2013b), "Large amplitude free vibration analysis of thermally post-buckled composite doubly curved panel embedded with SMA fibers", Nonlin. Dyn., 74(1-2), 395-418. https://doi.org/10.1007/s11071-013-0978-5
  37. Panda, S.K. and Singh, B.N. (2013c), "Post-buckling analysis of laminated composite doubly curved panel embedded with SMA fiber subjected to thermal environment", Mech. Adv. Mater. Struct., 20(10), 842-853. https://doi.org/10.1080/15376494.2012.677097
  38. Panda, S.K., Mohapatra, T.R. and Kar, V.R. (2017), Nonlinear Finite Element Solution of Post-buckling Responses of FGM Panel Structure under Elevated Thermal Load and TD and TID Properties, MATEC Web of Conferences 109, 05005.
  39. Peng, L.X., Tao, Y., Liang, N., Li, L. and Teng, X. (2017), "Simulation of a crack in stiffened plates via a meshless formulation and FSDT", Int. J. Mech. Sci., 131-132, 880-890. https://doi.org/10.1016/j.ijmecsci.2017.07.063
  40. Rangarajan, R. and Gao, H. (2015), "A finite element method to compute three-dimensional equilibrium configurations of fluid membranes: Optimal parameterization", J. Comput. Phys., 297, 266-294. https://doi.org/10.1016/j.jcp.2015.05.001
  41. Seifi, R. and Kabiri, A.R. (2013), "Lateral Load effects on buckling of cracked plates under tensile loading", Thin-Wall. Struct., 72, 37-47. https://doi.org/10.1016/j.tws.2013.06.010
  42. Seifi, R. and Khodayari, N. (2011), "Experimental and numerical studies on buckling of cracked thin-plates under full and partial compression edge loading", Thin-Wall. Struct., 49, 1504-1516. https://doi.org/10.1016/j.tws.2011.07.010
  43. Shahverdi, H. and Navardi, M.M. (2017), "Free vibration analysis of cracked thin plates using generalized differential quadrature element method", Struct. Eng. Mech., 62(3), 345-355. https://doi.org/10.12989/sem.2017.62.3.345
  44. Viola, E., Tornabene, F. and Fantuzzi, F. (2013a), "Generalized differential quadrature finite element method for cracked composite structures of arbitrary shape", Compos. Struct., 106, 815-834. https://doi.org/10.1016/j.compstruct.2013.07.034
  45. Viola, E., Tornabene, F., Ferretti, E. and Fantuzzi, F. (2013b), "GDQFEM numerical simulations of continuous media with cracks and discontinuities", Comput. Model. Eng. Sci., 94(4), 331-369.
  46. Yang, Q.J., Hayman, B. and Osnes, H. (2013), "Simplified buckling and ultimate strength analysis of composite plates in compression", Compos. Part B: Eng., 54, 343-352. https://doi.org/10.1016/j.compositesb.2013.05.017
  47. Yuan, J. and Dickinson, S.M. (1992), "Flexural vibration of rectangular plate systems approached by using artificial springs in the Rayleigh-Ritz method", J. Sound Vibr., 159(1), 39-55. https://doi.org/10.1016/0022-460X(92)90450-C

피인용 문헌

  1. Nonlinear and post-buckling responses of FGM plates with oblique elliptical cutouts using plate assembly technique vol.34, pp.2, 2020, https://doi.org/10.12989/scs.2020.34.2.227
  2. PROGRESSIVE FAILURE ANALYSIS OF HELICOPTER ROTOR BLADE UNDER AEROELASTIC LOADING vol.24, pp.1, 2018, https://doi.org/10.3846/aviation.2020.12184