DOI QR코드

DOI QR Code

선외기 선박용 비접촉 러더센서 및 자동조향장치 개발

Development of Outboard Type Contactless Rudder Sensor and Automatic Steering System

  • Kim, Ho-Young (Dept. of IT Applied System Engineering, Chonbuk National University) ;
  • Bang, Junho (Dept. of IT Applied System Engineering, Chonbuk National University) ;
  • Kim, Tae-Hyung (Dept. of IT Applied System Engineering, Chonbuk National University) ;
  • Ryu, In-Ho (Dept. of IT Applied System Engineering, Chonbuk National University)
  • 투고 : 2017.06.05
  • 심사 : 2017.07.11
  • 발행 : 2017.08.01

초록

In this paper, we developed a core module of the steering system to control and operate the outboard ship with the automatic steering system, and implemented it as a complete integrated system. In particular, this paper presents the problem of the rudder sensor used in the existing system and implements the contactless rudder sensor as an improvement. In the case of existing rudder sensors, there is a problem that safety operation and economic loss of the ship operation is caused by malfunction due to immersion during use in outboard vessels. However, the proposed rudder sensor is separated from the rotary shaft to constitute a contactless type, and a circular magnet is fixed so that the rotating value can be detected and used by the Hall sensor to completely solve the flooding problem. As a result of the characteristic test, the voltage value from 1.8V to 3.2V was obtained between $-35^{\circ}$ and $+35^{\circ}$ degrees and satisfied the reference value. The proposed rudder sensor was mounted on the outboard ship, and all the performance of controller system were checked. According to the system proposed in this paper, it satisfies the Korean Standard Specification, which defines the speed of convergence in 30 seconds by switching from left to right in 7 seconds. We also confirmed that automatic steering was performed by comparing the compass sensor with the destination in the integrated controller at the start-up.

키워드

참고문헌

  1. D. Kang, V. Nagarajan, K. Hasegawa and M. Sano "Mathematical model of single-propeller twin-rudder ship" Journal of Marine Science and Technology" Volume 13, Issue 3, Aug. 2008.
  2. S. Khanfir, K. Hasegawa, V. Nagarajan, K. Shouji and S. K. Lee "Manoeuvring characteristics of twin-rudder systems: rudder-hull interaction effect on the manoeuvrability of twin-rudder ships" Journal of Marine Science and Technology, Volume 16, Issue 4, Dec. 2011.
  3. T. I. Fossen and T. Perez "Kalman filtering for positioning and heading control of ships and offshore rigs" IEEE Control Systems, Volume: 29, Issue: 6, Dec. 2009.
  4. Y. M Lee, K. Y Lee, S. H Bae, H. Jang and J. K. Lee, "Defect detection and defect classification system for ship engine using multi-channel vibration sensor", Journal of Information Processing Society, Vol. 17, No. 2, pp. 81-92. 2010.
  5. J. B. Yim, "Evaluation and selection of MEMS-based inertial sensor to implement inertial measurement unit for a small-sized vessel" Journal of Navigation and Port Research, Volume 35, Issue 10, 2011.
  6. S.K. Lee and G. H. Kang, "Study on motor control type hydraulic driver for ship electro-hydraulic steering gear to improve energy efficiency", KIEE, Vol. 2014, No. 7, 2014.
  7. J. H Byun, " A study on heading angle control of a small ship with 3 position solenoid valve" Bulletin of the fisheries science institute, Vol. 17, No. 2, 2008.
  8. K. S Ko and C. M. Choi "A study on improvement of the ship's bearing information using GPS, vol 9, no 3, pp 528-533
  9. Q. Ladetto, J. Seeters, S. Sokolowski, Z. Sagan, and B. Merminod, "Digital magnetic compass and gyroscope for dismounted soldier position & navigation," 2002.
  10. ICAS, S10-Rudders-Sole Pieces and Rudder Horns-Common Structure Rule, pp. 1-16, 2010.
  11. Korean Register of Shipping, "Rules for the classification of steel ship", pp. 92. 2003.