DOI QR코드

DOI QR Code

Impact resistance of polypropylene fiber reinforced concrete two-way slabs

  • Al-Rousan, Rajai Z. (Department of Civil Engineering, Jordan University of Science and Technology) ;
  • Alhassan, Mohammed A. (Department of Civil Engineering, Jordan University of Science and Technology) ;
  • Al-Salman, Harith (Department of Civil Engineering, Jordan University of Science and Technology)
  • 투고 : 2016.08.24
  • 심사 : 2017.02.24
  • 발행 : 2017.05.10

초록

Concrete structures are often subjected to long-term static and short-term dynamic loads. Due to a relatively low tensile strength and energy dissipating characteristics, the impact resistance of concrete is considered poor. This study investigates the feasibility of using polypropylene fibers to improve the impact resistance of reinforced concrete slabs. Fourteen polypropylene fiber reinforced concrete slabs were fabricated and tested using a drop weight test. The effects of slab thickness, fiber volume fractions, and impact energy on the dynamic behaviors were evaluated mainly in terms of impact resistant, crack patterns, and failure modes. The post impact induced strains versus time responses were obtained for all slabs. The results showed that adding the polypropylene fiber at a dosage of 0.90% by volume of concrete leads to significant improvement in the overall structural behavior of the slabs and their resistance to impact loading. Interestingly, the enhancement in the behavior of the slabs using a higher fiber dosage of 1.2% was not as good as achieved with 0.90%.

키워드

과제정보

연구 과제 주관 기관 : Jordan University of Science and Technology

참고문헌

  1. ACI Committee 318 (2014), "Building Code Requirements for Reinforced Concrete", (ACI 318-14) and Commentary (318R-14), American Concrete Institute, Farmington Hills, M.I.
  2. Banthia, N.P., Mindess, S. and Bentur, A. (1987), "Impact behavior of concrete beams", Mater. Struct., 20(118), 293-302. https://doi.org/10.1007/BF02485926
  3. Campione, G. (2011), "Compressive behavior of short fibrous reinforced concrete members with square cross-section", Struct. Eng. Mech., 37(6), 649-669. https://doi.org/10.12989/sem.2011.37.6.649
  4. Elavenil, S. and Samuel Knight, G.M. (2012), "Impact response of plates under drop weight impact testing", Daffodil Int. Univ. J. Sci. Tech., 7(1), 1-11.
  5. Ghanem, A. (2009), "Behavior of reinforced concrete slabs under impact", PhD Thesis, Department of Civil Engineering, College of Engineering, University of Baghdad.
  6. Ibraheema, O.F., Abu, B. and Joharib, I. (2015), "Behavior and crack development of fiber-reinforced concrete spandrel beams under combined loading: an experimental study", Struct. Eng. Mech., 54(1), 1-17. https://doi.org/10.12989/sem.2015.54.1.001
  7. Keer, J.G. (1984), "New reinforced concretes: concrete technology and design", Ed. Swamy, R.N., Surrey University Press, 2(1), 2-105.
  8. Ma, Y., Zhu, B., Tan, M. and Wu, K. (2004), "Effect of type polypropylene fiber on plastic shrinkage cracking of cement mortar", Mater. Construct., 37(1), 92-95.
  9. May, I.M., Chen, Y., Owen, D.R.J., Feng, Y.T. and Thiele, P.J. (2006), "Reinforced concrete beams under drop-weight impact loads", Comput. Concrete, 3(2-3), 79-90. https://doi.org/10.12989/cac.2006.3.2_3.079
  10. Murtiadi, S. (1999), "Behavior of high-strength concrete plates under impact loading", M.Sc. Thesis, Faculty of Engineering and Applied Science, Memorial University of Newfoundland.
  11. Newman, J. and Choo, B. (2003), Advanced Concrete Technology 3: Processes, 1st Edition, Elsevier Ltd, Oxford.
  12. Parveen, I. and Ankit, S. (2013), "Structural behavior of fibrous concrete using polypropylene", Int. J. Eng. Res., 3(3), 1279-1282.
  13. Perry, B. (2003), "Reinforcing external pavements with both large and small synthetic fibers", High Beam Res., 37(8), 46-47.
  14. Ramakrishnan, V. (1987), "Materials and properties of fibre reinforced concrete", Proc. of ISFRC, 1(1), 3-24.
  15. Safan, M.A. (2012), "Behaviour of fiber reinforced concrete beams with spliced tension steel reinforcement", Struct. Eng. Mech., 43(5), 623-636. https://doi.org/10.12989/sem.2012.43.5.623
  16. Sawan, J. and Abdul-Rohman, M. (1986), "Impact effect on RC slabs: experimental approach", ASCE J. Struct. Eng.; 112(9), 2057-2065. https://doi.org/10.1061/(ASCE)0733-9445(1986)112:9(2057)
  17. Tuladhar, R. and Lancini, B.J. (2014), "Ductility of concrete slabs reinforced with low-ductility welded wire fabric and steel fibers", Struct. Eng. Mech., 49(4), 449-461. https://doi.org/10.12989/sem.2014.49.4.449
  18. Zarrin, O. and Khoshnoud, H.R. (2016), "Experimental investigation on self-compacting concrete reinforced with steel fibers", Struct. Eng. Mech., 59(1), 133-151. https://doi.org/10.12989/sem.2016.59.1.133

피인용 문헌

  1. Theoretical and experimental analysis of wave propagation in concrete blocks subjected to impact load considering the effect of nanoparticles vol.20, pp.6, 2017, https://doi.org/10.12989/cac.2017.20.6.711
  2. Performance Evaluation of Metallic and Synthetic Fiber Hybridization on the Cyclic Behavior of Exterior Beam-Column Joint vol.7, pp.1, 2017, https://doi.org/10.1520/acem20170137
  3. Effect of waste cement bag fibers on the mechanical strength of concrete vol.8, pp.2, 2017, https://doi.org/10.12989/amr.2019.8.2.103
  4. Dynamic performance of concrete slabs reinforced with steel and GFRP bars under impact loading vol.191, pp.None, 2019, https://doi.org/10.1016/j.engstruct.2019.04.038
  5. Hybrid-fibre-reinforced concrete containing multi-wall carbon nanotubes vol.173, pp.9, 2017, https://doi.org/10.1680/jstbu.18.00180
  6. Performance of Geogrid Reinforced Concrete Slabs under Drop Weight Impact Loading vol.981, pp.None, 2017, https://doi.org/10.1088/1757-899x/981/3/032070
  7. Performance of Geogrid Reinforced Concrete Slabs under Drop Weight Impact Loading vol.981, pp.None, 2017, https://doi.org/10.1088/1757-899x/981/3/032070