소성∙가공 (Transactions of Materials Processing)

  • 제26권1호
  • /
  • Pages.18-27
  • /
  • 2017
  • /
  • 1225-696X(pISSN)
  • /
  • 2287-6359(eISSN)
한국소성∙가공학회 (The Korean Society for Technology of Plasticity and materials processing)
권호 표지
DOI QR코드

DOI QR Code

A Comparative Study on Arrhenius-Type Constitutive Models with Regression Methods

  • Lee, Kyunghoon (Department of Aerospace Engineering, Pusan National University) ;
  • Murugesan, Mohanraj (Department of Mechanical Engineering, Sogang University) ;
  • Lee, Seung-Min (Department of Aerospace Engineering, Pusan National University) ;
  • Kang, Beom-Soo (Department of Aerospace Engineering, Pusan National University)
  • 투고 : 2016.10.17
  • 심사 : 2016.12.21
  • 발행 : 2017.02.01
PDF 다운로드
⟨ 이전 논문 다음 논문 ⟩

초록

A comparative study was performed on strain-compensated Arrhenius-type constitutive models established with two regression methods: polynomial regression and regression Kriging. For measurements at high temperatures, experimental data of 70Cr3Mo steel were adopted from previous research. An Arrhenius-type constitutive model necessitates strain compensation for material constants to account for strain effect. To associate the material constants with strain, we first evaluated them at a set of discrete strains, then capitalized on surrogate modeling to represent the material constants as a function of strain. As a result, disparate flow stress models were formed via the two different regression methods. The constructed constitutive models were examined systematically against measured flow stresses by validation methods. The predicted material constants were found to be quite accurate compared to the actual material constants. However, notable mismatches between measured and predicted flow stresses were revealed by the proposed validation techniques, which carry out validation with not the entire, but a single tensile test case.

키워드

참고문헌

  1. Y. C. Lin, X. M. Chen, 2011, A Critical Review of Experimental Results and Constitutive Descriptions for Metals and Alloys in Hot Working, Mater. Des., Vol. 32, No. 4, pp. 1733-1759. https://doi.org/10.1016/j.matdes.2010.11.048
  2. H. Y. Li, D. D. Wei, Y. H. Li, and X. F. Wang, 2012, Application of Artificial Neural Network and Constitutive Equations to Describe the Hot Compressive Behavior of 28CrMnMoV Steel, Mater. Des., Vol. 35, pp. 557-562. https://doi.org/10.1016/j.matdes.2011.08.049
  3. A. K. Gupta, S. K. Singh, S. Reddy, and G. Hariharan, 2012, Prediction of Flow Stress in Dynamic Strain Aging regime of Austenitic Stainless Steel 316 Using Artificial Neural Network, Mater. Des., Vol. 35, pp. 589-595. https://doi.org/10.1016/j.matdes.2011.09.060
  4. A. K. Sulochana, C. Phaniraj, C. Ravishankar, A. K. Bhaduri, and P. V. Sivaprasad, 2011, Prediction of High Temperature Flow Stress in 9Cre1Mo Ferritic Steel During Hot Compression, Int. J. Pres. Ves. Pip., Vol. 88, No. 11, pp. 501-506. https://doi.org/10.1016/j.ijpvp.2011.07.009
  5. F. Ren and J. Chen, 2013, Modeling Flow Stress of 70Cr3Mo Steel Used for Back-Up Roll During Hot Deformation Considering Strain Compensation, J. Iron Steel Res. Int., Vol. 20, No. 11, pp. 118-124. https://doi.org/10.1016/S1006-706X(13)60206-X
  6. M. L. Ma, X. G. Li, Y. J. Li, L. Q. He, K. Zhang, X. W. Wang, and L. F. Chen, 2011, Establishment and Application of Flow Stress Models of Mg-Y-MM-Zr Alloy, Trans. Nonferrous Met. Soc. China, Vol. 21, No. 4, pp. 857-862. https://doi.org/10.1016/S1003-6326(11)60793-0
  7. M. R. Rokni, A. Zarei-Hanzaki, C. A. Widener, and P. Changizian, 2014, The Strain-Compensated Constitutive Equation for High Temperature Flow Behavior of an Al-Zn-Mg-Cu Alloy, J. Mater. Eng. Perform., Vol. 23, No. 11, pp. 4002-4009. https://doi.org/10.1007/s11665-014-1195-1
  8. Y. K. Kim, J. O. Jo, J. P. Hong, and J. Hur, 2002, Application of Response Surface Methodology to Robust Design of BLDC Motor, KIEE EMECS, Vol. 12B, No. 2, pp. 47-51.
  9. A. I. Khuri and S. Mukhopadhyay, 2010, Response Surface Methodology, Wiley Interdiscip. Rev. Comput. Stat., Vol. 2, No. 2, pp. 128-149. https://doi.org/10.1002/wics.73
  10. M. Murugesan, B. S. Kang and K. Lee, 2015, Multi-Objective Design Optimization of Composite Stiffened Panel Using Response Surface Methodology, Compos. Res., Vol. 28, No. 5, pp. 297-310. https://doi.org/10.7234/composres.2015.28.5.297
  11. W. S. Cleveland and S. J. Devlin, 1988, Locally Weighted Regression: An Approach to Regression Analysis by Local Fitting, J. Am. Stat. Assoc, Vol. 83, No. 403, pp. 596-610. https://doi.org/10.1080/01621459.1988.10478639
  12. MathWorks, 2015, Curve Fitting Toolbox User's Guide
  13. I. Couckuyt, T. Dhaene, and P. Demeester, 2014, ooDACE Toolbox: A Flexible Object-Oriented Kriging Implementation, J. Mach. Learn. Res., Vol. 15, No. 1, pp. 3183-3186.
  14. I. Couckuyt, A. Forrester, D. Gorissen, F. D. Turck, and T. Dhaene, 2012, Blind Kriging: Implementation and Performance Analysis, Adv. Eng. Softw., Vol. 49, pp. 1-13. https://doi.org/10.1016/j.advengsoft.2012.03.002
  15. I. Couckuyt, F. Declercq, T. Dhaene, H. Rogier, and L. Knockaert, 2010, Surrogate-Based Infill Optimization Applied to Electromagnetic Problems, Int. J. Rf. Microw. C. E., Vol. 20, No. 5, pp. 492-501. https://doi.org/10.1002/mmce.20455

피인용 문헌

  1. Johnson Cook Material and Failure Model Parameters Estimation of AISI-1045 Medium Carbon Steel for Metal Forming Applications vol.12, pp.4, 2019, https://doi.org/10.3390/ma12040609