DOI QR코드

DOI QR Code

Effect of the yield criterion on the strain rate and plastic work rate intensity factors in axisymmetric flow

  • Lyamina, Elena A. (Laboratory for Strength and Fracture of Materials and Structures, Institute for Problems in Mechanics) ;
  • Nguyen, Thanh (Institute of Mechanics, Vietnam Academy of Science and Technology)
  • 투고 : 2015.10.18
  • 심사 : 2016.01.29
  • 발행 : 2016.05.25

초록

The main objective of the present paper is to study the effect of the yield criterion on the magnitude of the strain rate and plastic work rate intensity factors in axisymmetric flow of isotropic incompressible rigid perfectly plastic material by means of a problem permitting a closed-form solution. The boundary value problem consisting of the axisymmetric deformation of a plastic tube is solved. The outer surface of the tube contracts. The radius of the inner surface does not change. The material of the tube obeys quite a general yield criterion and its associated flow rule. The maximum friction law is assumed at the inner surface of the tube. Therefore, the velocity field is singular near this surface. In particular, the strain rate and plastic work rate intensity factors are derived from the solution. It is shown that the strain rate intensity factor does not depend on the yield criterion but the plastic work rate intensity factor does.

키워드

참고문헌

  1. Alexandrov, S. (2009), "The strain rate intensity factor and its applications: a review", Mater. Sci. Forum, 623, 1-20. https://doi.org/10.4028/www.scientific.net/MSF.623.1
  2. Alexandrov, S.E. and Goldstein, R.V. (2015), "On constructing constitutive equations in metal thin layer near friction surfaces in material forming processes", Doklady Physics, 60(1), 39-41. https://doi.org/10.1134/S1028335815010085
  3. Alexandrov, S. and Jeng, Y.R. (2013), "Singular rigid/plastic solutions in anisotropic plasticity under plane strain conditions", Cont. Mech. Therm., 25(5), 685-689. https://doi.org/10.1007/s00161-013-0304-y
  4. Alexandrov, S., Jeng, Y.R. and Hwang, Y.M. (2015), "Generation of a fine grain layer in the vicinity of frictional interfaces in direct extrusion of AZ31 alloy", ASME J. Manuf. Sci. Eng., 137(5), Paper 051003. https://doi.org/10.1115/1.4030267
  5. Alexandrov, S. and Lyamina, E. (2006), "Prediction of fracture in the vicinity of fiction surfaces in metal forming processes", J. Appl. Mech. Techn. Phys., 47(5), 757-761. https://doi.org/10.1007/s10808-006-0112-2
  6. Alexandrov, S. and Mustafa, Y. (2014), "The strain rate intensity factor in the plane strain compression of thin anisotropic metal strip", Meccanica, 49(12), 2901-2906. https://doi.org/10.1007/s11012-014-0039-2
  7. Alexandrov, S. and Richmond, O. (2001), "Singular plastic flow fields near surfaces of maximum friction stress", Int. J. Nonlin. Mech., 36(1), 1-11. https://doi.org/10.1016/S0020-7462(99)00075-X
  8. Choi, Y. (2010), "Influence of a white layer on the performance of hard machined surfaces in rolling contact", Proceedings of the Institution of Mechanical Engineers Part B: Journal of Engineering Manufacture, 224(8), 1207-1215. https://doi.org/10.1243/09544054JEM1847
  9. Griffiths, B.J. (1987), "Mechanisms of white layer generation with reference to machining and deformation processes", ASME J. Tribology, 109(3), 525-530. https://doi.org/10.1115/1.3261495
  10. Griffiths, B.J. and Furze, D.C. (1987), "Tribological advantages of white layers produced by machining", ASME J. Tribology, 109(2), 338-342. https://doi.org/10.1115/1.3261363
  11. Hosford, W.F. (1972), "A generalized isotropic yield criterion", Tran. ASME J. Appl. Mech., 39, 607-609. https://doi.org/10.1115/1.3422732
  12. Kajino, S. and Asakawa, M. (2006), "Effect of "additional shear strain layer" on tensile strength and microstructure of fine drawn wire", J. Mater. Proc. Technol., 177, 704-708. https://doi.org/10.1016/j.jmatprotec.2006.04.108
  13. Murai, T., Matsuoka, S., Miyamoto, S. and Oki, Y. (2003), "Effects of extrusion conditions on microstructure and mechanical properties of AZ31B magnesium alloy extrusions", J. Mater. Proc. Technol., 141, 207-212. https://doi.org/10.1016/S0924-0136(02)01106-8
  14. Shield, R.T. (1955), "Plastic flow in a converging conical channel", J. Mech. Phys. Solid., 3, 246-258. https://doi.org/10.1016/0022-5096(55)90035-1
  15. Spencer, A.J.M. (1965), "A theory of the failure of ductile materials reinforced by elastic fibres", Int. J. Mech. Sci., 7, 197-209. https://doi.org/10.1016/0020-7403(65)90018-4
  16. Trunina, T.A. and Kokovkhin, E.A. (2008), "Formation of a finely dispersed structure in steel surface layers under combined processing using hydraulic pressing", J. Mach. Manuf. Reliab., 37(2), 160-162. https://doi.org/10.3103/S1052618808020118
  17. Warren, A.W. and Guo, Y.B. (2005), "Numerical investigation on the effects of machining-induced white layer during rolling contact", Tribology Tran., 48(3), 436-441. https://doi.org/10.1080/05698190500225078

피인용 문헌

  1. A numerical solution for the axisymmetric flow of a plastic tube on a rigid fibre vol.885, 2017, https://doi.org/10.1088/1742-6596/885/1/012018