DOI QR코드

DOI QR Code

Dynamic shear strength of unreinforced and Hairpin-reinforced cast-in-place anchors using shaking table tests

  • Kim, Dong Hyun (Department of Civil Engineering, Pusan National University) ;
  • Park, Yong Myung (Department of Civil Engineering, Pusan National University) ;
  • Kang, Choong Hyun (Seismic Simulation Test Center, Pusan National University) ;
  • Lee, Jong Han (Department of Civil Engineering, Daegu University)
  • 투고 : 2015.08.07
  • 심사 : 2016.01.11
  • 발행 : 2016.04.10

초록

Since the publication of ACI 318-02, the concrete capacity design (CCD) method has been used to determine the resistance of unreinforced concrete anchors. The regulation of steel-reinforced anchors was proposed in ACI 318-08. Until ACI 318-08, the shear resistance of concrete breakout for an unreinforced anchor during an earthquake was reduced to 75% of the static shear strength, but this reduction has been eliminated since ACI 318-11. In addition, the resistance of a hairpin-reinforced anchor was calculated using only the strength of the steel, and a regulation on the dynamic strength was not given for reinforced anchors. In this study, shaking table tests were performed to evaluate the dynamic shear strength of unreinforced and hairpin-reinforced cast-in-place (CIP) anchors during earthquakes. The anchors used in this study were 30 mm in diameter, with edge distances of 150 mm and embedment depths of 240 mm. The diameter of the hairpin steel was 10 mm. Shaking table tests were carried out on two specimens using the artificial earthquake, based on the United States Nuclear Regulatory Commission (US NRC)'s Regulatory Guide 1.60, and the Northridge earthquake. The experimental results were compared to the current ACI 318 and ETAG 001 design codes.

키워드

과제정보

연구 과제 주관 기관 : National Research Foundation of Korea

참고문헌

  1. ACI Committee 318 (2002), Building Code Requirements for Structural Concrete and Commentary, ACI 318-02, Appendix D: Anchoring to concrete, American Concrete Institute.
  2. ACI Committee 318 (2008), Building Code Requirements for Structural Concrete and Commentary, ACI 318-08, Appendix D: Anchoring to concrete, American Concrete Institute.
  3. ACI Committee 318 (2011), Building Code Requirements for Structural Concrete and Commentary, ACI 318-11, Appendix D: Anchoring to concrete, American Concrete Institute.
  4. ACI Committee 318 (2014), Building Code Requirements for Structural Concrete and Commentary, ACI 318-14, Chap. 17 Anchoring to concrete, American Concrete Institute.
  5. ACI Committee 349 (2001), Code Requirements for Nuclear Safety Related Concrete Structures (ACI 349-01); Appendix B Anchoring to Concrete, American Concrete Institute.
  6. ACI 355.2 (2000), Evaluating the Performance of Post-installed Mechanical Anchors in Concrete, Reported by ACI Committee 355.
  7. CSA N287.2 (1998), Material Requirements for Concrete Containment Structures for CANDU Nuclear Power Plants, Canadian Standards Association, Rexdale, Ontario.
  8. Eligehausen, R. and Hofmann, J. (2003), "Experimental and numerical investigation on fixings under shear loading close to an edge", Report, Institute of Construction Materials, University of Stuttgart. (in German)
  9. Eligehausen, R., Mallee, R. and Silva, J.F. (2006), Anchorage in Concrete Construction, Ernst & Sohn, Germany.
  10. ETAG 001 (2012), Guideline for European Technical Approval of Metal Anchors for Use in Concrete, European Organization for Technical Approvals (EOTA).
  11. Gross, J.H., Klingner, R.E. and Graves III, H.L. (2001), "Dynamic anchor behavior of single and double near-edge anchors loaded in shear", Proc. of Connections between Steel and Concrete, Int. Conference organized by University of Stuttgart, fib, IABSE, Ed. R. Eligehausen, RILEM Publications S.A.R.L.
  12. Klingner, R.E., Mendonca, J.A. and Malik, J.B. (1982), "Effect of reinforcing details on the shear resistance of short anchor bolts under reversed cyclic loading", ACI J., 79(1), 3-12.
  13. Lee, N.H., Park, K.R. and Suh, Y.P. (2010), "Shear behavior of headed anchors with large diameters and deep embedments", ACI Struct. J., 107(4), 146-156.
  14. Malvar, L.J. and Crawford, J.E. (1998), "Dynamic increase factors for steel reinforcing bars", Proc. of the Twenty-Eighth DDESB Seminar, Orlando, Florida.
  15. Pajak, M. (2011), "The influence of the strain rate on the strength of concrete taking into account the experimental technique", Architecture Civil Engineering Environment, The Silesian University of Technology.
  16. Park, Y.M., Kang, M.K., Roh, J.K., Ju, H.J. and Kang, C.H. (2014), "Shear resistance of CIP anchors under dynamic loading: Reinforced anchor", J. Korean Soc. Steel Constr., 26(1), 21-31. (in Korean) https://doi.org/10.7781/kjoss.2014.26.1.021
  17. Petersen, D., Lin, Z. and Zhao, J. (2013), "Behavior and design of cast-in-place anchors under simulated seismic loading", Draft Final Report, Vol. 1, Cyclic Behavior of Single Headed Anchors, Department of Civil Engineering, University of Wisconsin, Milwaukee.
  18. US NRC Regulatory Guide 1.60 (1973), Design response spectra for seismic design of nuclear power plants, United States Nuclear Regulatory Commission, Washington.