DOI QR코드

DOI QR Code

Fabrication and characterization of Copper/Silicon Nitride composites

  • Ahmed, Mahmoud A. (Department of Production Technology, Faculty of Industrial Education, Helwan University) ;
  • Daoush, Walid M. (Department of Production Technology, Faculty of Industrial Education, Helwan University) ;
  • El-Nikhaily, Ahmed E. (Mechanical Department, Faculty of Industrial Education, Suez University)
  • 투고 : 2016.05.29
  • 심사 : 2016.10.19
  • 발행 : 2016.09.25

초록

Copper/silicon nitride ($Cu/Si_3N_4$) composites are fabricated by powder technology process. Copper is used as metal matrix and very fine $Si_3N_4$ particles (less than 1 micron) as reinforcement material. The investigated powder were used to prepare homogenous ($Cu/Si_3N_4$) composite mixtures with different $Si_3N_4$ weight percentage (2, 4, 6, 8 and10). The produced mixtures were cold pressed and sintered at different temperatures (850, 950, 1000, $1050^{\circ}C$). The microstructure and the chemical composition of the produced $Cu/Si_3N_4$ composites were investigated by (SEM) and XRD. It was observed that the $Si_3N_4$ particles were homogeneously distributed in the Cu matrix. The density, electrical conductivity and coefficient of thermal expansion of the produced $Cu/Si_3N_4$ composites were measured. The relative green density, sintered density, electrical conductivity as well as coefficient of thermal expansion were decreased by increasing the reinforcement phase ($Si_3N_4$) content in the copper matrix. It is also founded that the sintered density and electrical conductivity of the $Cu/Si_3N_4$ composites were increased by increase the sintering temperature.

키워드

참고문헌

  1. Allahkaram, S.R., Golroh, S. and Mohammad, M. (2011), "Properties of $Al_2O_3$ nano-particle reinforced copper matrix composite coatings prepared by pulse and direct current electroplating", Mater. Des., 32(8), 4478-4484. https://doi.org/10.1016/j.matdes.2011.03.042
  2. Arai, S., Saito, T. and Endo, M. (2010), "Cu-MWCNT composite films fabricated by electrode-position", J. Electrochem. Soc., 157(3), 147-153.
  3. Ashby, M.F. and Jones, D.R.H. (1996), Engineering Materials: An Introduction to Their Properties & Applications, 2nd ed., Butterworth-Heinemann, Oxford, UK.
  4. Baughman, R.H., Zakhidov, A.A. and de Heer, W.A. (2002), "Carbon nanotubes-the route towards applications", Science, 297(5582), 787-792. https://doi.org/10.1126/science.1060928
  5. Benea, L., Mitoseriu, O., Galland, J., Wenger, F. and Ponthiaux, P. (2000), "Corrosion study of copper composite coating by impedance spectroscopy method", Mater. Corros., 51(7), 491-495. https://doi.org/10.1002/1521-4176(200007)51:7<491::AID-MACO491>3.0.CO;2-C
  6. Gauche, P. and Xu, W. (2000), "Modeling phase change material in electronics using. CFD-a case study", Proceedings of the International Conference on High Density Interconnect and Systems Packaging, Denver, Colorado, April.
  7. Gilleo, K. and Dennis, J. (2005), "Injection molded & micro fabrication electronic packaging", Proceedings of Molding Conference, New Orleans, June.
  8. Lee, W.E. and Rainforth, W.M. (1994), Ceramic Microstructures, Property Control by Processing, Chapman & Hall, New York.
  9. Lekka, M., Koumoulis, D., Kouloumbi, N. and Bonora, P.L. (2009), "Mechanical and anti-corrosive properties of copper matrix micro- and nano-composite coatings", Electrochim. Acta, 54(9), 2540-2546. https://doi.org/10.1016/j.electacta.2008.04.060
  10. Li, H., Wan, Y., Liang, H., Li, X., Huang, Y. and He, F. (2009), "Composite electroplating of $Cu-SiO_2$ nanoparticles on carbon fiber reinforced epoxy composites", Appl. Surf. Sci., 256(5), 1614-1616. https://doi.org/10.1016/j.apsusc.2009.04.148
  11. Madou, M.J. (2002), Fundamentals of Microfabrication, 2nd ed., CRC Press, Boca Raton (FL).
  12. Massalski, T.B., Okamoto, H., Subramanian, P.R. and Kacprzak, L. (1995), Binary alloy phase diagrams, ASM International, 1485-1486.
  13. Mangam, V., Das, K. and Das, S. (2010), "Structure and properties of electrocodeposited $Cu-CeO_2$ nanocomposite thin films", Mater. Chem. Phys., 120(2), 631-635. https://doi.org/10.1016/j.matchemphys.2009.12.017
  14. Medeline, V., Juskenas, R. and Kurtinaitiene, M. (2004), "Copper metal matrix composite Cu-TiO electrodeposited in aqueous suspensions of the nanometric size particles of anatase and rutile", Pol. J. Chem., 78(9), 1305-1317.
  15. Medeliene, V. and Kosenko, A. (2008), "Structural and functional properties of electrodeposited copper metal matrix composite coating with inclusions of WC", Mater. Sci., 14(1), 29-33.
  16. Montes, J.M., Rodriguez, J.A. and Herrera, E.J. (2003), "Thermal and electrical conductivities of sintered powder compacts", Powder Metallurgy, 46, 251-255. https://doi.org/10.1179/003258903225008544
  17. Ramalingam, S., Muralidharan, V.S. and Subramania, A. (2009), "Electrodeposition and characterization of $Cu-TiO_2$ nanocomposite coatings", J. Solid. State Electrochem., 13(11), 1777-1783. https://doi.org/10.1007/s10008-009-0870-x
  18. Robin, A., Santana, J.C.P.d. and Sartori, A.F. (2011), "Co-electrodeposition and characterization of $Cu-Si_3N_4$ composite coatings", Surf. Coat. Technol., 205(19), 4596-4601. https://doi.org/10.1016/j.surfcoat.2011.03.142
  19. Stankovic, V.D. and Gojo, M. (1996), "Electrodeposited composite coatings of copper with inert, semiconductive and conductive particles", Surf. Coat. Technol., 81(2), 225-232. https://doi.org/10.1016/0257-8972(95)02486-7
  20. Sundberg, G. (2004), "CuSiC for IGBT thermal management", Adv. Microelectron. Nov. /Dec., 8-11.
  21. Terzieva, V., Fransaer, J. and Celis, J.P. (2000), "Codeposition of hydrophilic and hydropho-bic silica with copper from acid copper sulfate baths", J. Electrochem. Soc., 147(1), 198-202. https://doi.org/10.1149/1.1393174
  22. Weissgaerber, T., Lefranc, G. and Schulz-Harder, J. (2003), Advances in Powder Metallurgy & Particulate Materials, Part 6, Metal Powder Industries Federation, Princeton, NJ.
  23. Zhu, J., Liu, L., Zhao, H., Bin, S. and Wenbin, H. (2007), "Microstructure and performance of electroformed Cu/nano-SiC composite", Mater. Des., 28(6), 1958-1962. https://doi.org/10.1016/j.matdes.2006.04.021

피인용 문헌

  1. Microstructure and properties of BN/Ni-Cu composites fabricated by powder technology vol.13, pp.1, 2018, https://doi.org/10.1080/17458080.2018.1467049
  2. Investigation of the effect of SiC content on the microstructure, physical properties and hardness of SiC/Ni composites vol.26, pp.1, 2016, https://doi.org/10.15407/fm26.01.92
  3. Gr-Al composite reinforced with Si3N4 and SiC particles for enhanced microhardness and reduced thermal expansion vol.2, pp.6, 2016, https://doi.org/10.1007/s42452-020-2838-5
  4. Mechanical characterization of an epoxy panel reinforced by date palm petiole particle vol.35, pp.5, 2016, https://doi.org/10.12989/scs.2020.35.5.627
  5. Microstructure and Properties of Nickel/Detonated Nanodiamond Composites Fabricated by Powder Metallurgy vol.9, pp.4, 2016, https://doi.org/10.1520/mpc20190073