References
- The Asphalt Institute (2003). Performance graded asphlt binder specification and testing, SP-1. The Asphalt Institute, Lexington.
- Adhikari, B., De D, Maiti, S. (2000). Reclamation and recycling of waste rubber. Prog Polym Sci, 25(7), 909-48. https://doi.org/10.1016/S0079-6700(00)00020-4
- Azizian, F., & Nelson, O., Thayumanavan, P. & Williamson, J. (2003). Environmental impact of highway construction and repair materials on surface and ground waters: case study: crumb rubber asphalt concrete. Waste Manage, 22(8), 719-28.
- Bahia, H. U., & Davis, R. (1994). Effect of crumb rubber modifiers (CRM) on performance-related properties of asphalt binders. J. Assoc. Asphalt Paving Technol., 63, 414-449.
- Bahia, H. U., Hanson, D. I., Zeng, M., Zhai, H., Khatri, M. A., & Anderson, R. M. (2001). Characterization of modified asphalt binders in superpave mix design. Rep. No. 459, Transportation Research Board, National Research Council, Washington, DC.
- Blumenthal, M. (1994). Producing ground scrap tire rubber: A comparison between ambient and cryogenic technologies. Proc., 17th Biennial Waste Processing Conf., ASME, New York.
- Danilatos, G.D., (1990). Theory of the gaseous detector device in the environmental scanning electron microscope. Advances in Electronics and Electron Physics, 78, 1-102. https://doi.org/10.1016/S0065-2539(08)60388-1
- Divya, P. S., Gideon, C. S., & Krishnan, M. (2013). Influence of the type of binder and crumb rubber on the creep and recovery of crumb rubber modified bitumen. Journal of Materials in Civil Engineering, 25(4), 438-449. https://doi.org/10.1061/(ASCE)MT.1943-5533.0000608
- Garcia-Morales M, Partal P, Navarro FJ, Gallegos C. (2006). Effect of waste polymer addition on the rheology of modified bitumen, Fuel, 85, 936-945. https://doi.org/10.1016/j.fuel.2005.09.015
- Heitzman, M. (1992). "State of the practice design and construction of asphalt paving materials with crumb rubber modifier." Rep. No. FHWA A-SA-92-022, Federal Highway Administration, Washington, DC.
- Huang B, Mohammad LN, Graves PS, Abadie C. (2002). Louisiana experience with crumb rubber-modified hot-mix asphalt pavement. Transport Res Rec: J Transport Res Board, 1789, 1-13. https://doi.org/10.3141/1789-01
- Karakurt, C. (2014). Microstructure properties of waste tire rubber composites: an overview. J Mater Cycles Waste Mang, 17, 422-433.
- Kimseng, K. & Meissel, M. (2001). Short overview about the ESEM: The Environmental Scanning Electron Microscope. Maryland: Produced by CALCE Electronic Products and Systems Centre, University of Maryland.
- Kim, H. & Lee, S.-J. (2013). Laboratory investigation of different standards of phase separation in crumb rubber modified asphalt binders. Journal of Materials in Civil Engineering, 25(12), 1975-1978. https://doi.org/10.1061/(ASCE)MT.1943-5533.0000751
- Lee, S.-J., Amirkhanian, S., & Shatanawki, K. (2006). Effects of crumb rubber on aging of asphlt binders. In: Asphalt rubber 2006, 3, California: Palm Springs, 779-95.
- Lee, S.-J. (2007). Characterization of recycled aged CRMA binders. Dissertation (Ph.D.), Clemson University.
- Liu, H., Chen, Z., Wang, W., Wang, H., & Hao, P. (2014). Investigation of the rheological modification mechanism of crumb rubber modified asphalt (CRMA) containing TOR additive. Construction and Building Materials, 67, 225-233. https://doi.org/10.1016/j.conbuildmat.2013.11.031
- Liang, RY., & Lee S. (1996). Short-term and long-term aging behavior of rubber modified asphalt paving mixtures. Transport Res Rec: J Transpor Res Board,1530(1), 1-7.
- Loeber, L., Sutton, O., Morel, J.V.J.M., Valleton, J.M. & Muller, G. (1996). New direct observations of asphalts and asphalt binders by scanning electron microscopy and atomic force microscopy. Journal of Microscopy, 182(1), 32-39. https://doi.org/10.1046/j.1365-2818.1996.134416.x
- Masson, J.F., Leblond, V. & Margeson, J. (2006). Bitumen morphologies by phase-detection atomic force microscopy. Journal of Microscopy, 221(1), 17-29. https://doi.org/10.1111/j.1365-2818.2006.01540.x
- Palit, S. K., Sudhakar Reddy, K., & Pandey, BB. (2004). Laboratory evaluation of crumb rubber modified asphalt mixes. J Mater Civ Eng, 16(1), 45-53. https://doi.org/10.1061/(ASCE)0899-1561(2004)16:1(45)
- Polacco, G., Stastna, J., Biondi, D., & Zanzotto, L. (2006). Relation between Polymer architecture and nonlinear viscoelastic behavior of modified asphalts, Current Opinion in Colloid & Interface Science, 11(4), 230-245. https://doi.org/10.1016/j.cocis.2006.09.001
- Putman, B.J. (2005). Qualification of the Effects of Crumb Rubber in CRM Binder, Dissertation (Ph.D.), Clemson University.
- Rozeveld, S. J., Shin, E. E., Bhurke, A., France, L., & Drzal, L. T.(1997). Network morphology of straight and polymer modified asphalt cements. Microsc. Res. Tech., 38(5), 529-543. https://doi.org/10.1002/(SICI)1097-0029(19970901)38:5<529::AID-JEMT11>3.0.CO;2-O
- Ruth, B.E., & Roque, R. (1995). Crumb rubber modifier (CRM) in asphalt pavements. In: Proceedings of the transportation congress, 768-85.
- Shen, J., & Amirkhanian, S.N. (2005). The influence of crumb rubber modifier (CRM) microstructures on the high temperature properties of CRM binders, The International Journal of Pavement Engineering, 6(4), 265-271. https://doi.org/10.1080/10298430500373336
- Sun, D., & Lu W. (2003). Investigation and Improvement of storage stability of SBS modified asphalt, Petroleum Science and Technology, 21, 901-910. https://doi.org/10.1081/LFT-120017456
- Shen, J., Amirkhanian, S.N., Xiao, F., &Tang, B. (2009)". Influence of surface area and size of crumb rubber on high temperature properties of crumb rubber modified binders." Constr. Build. Mater., 23(1), 304-310. https://doi.org/10.1016/j.conbuildmat.2007.12.005
- Siddique, R., & Naik, T. R. (2004). Properties of concrete containing scrap-tire rubber-An overview. Waste Manage., 24(6), 563-569. https://doi.org/10.1016/j.wasman.2004.01.006
- Visser, A., and Verhaegle, B. (2000). "Bitumen rubber: Lessons learned in South Africa." Proc., Asphalt Rubber, Faro, Portugal (Nov. 14-17, 2000).
- Wang, H., You, Z., Mills-Beale, J., & Hao, P. (2012a). Laboratory evaluation on high temperature viscosity and low temperature stiffness of asphalt binder with high percent scrap tire rubber. Constr. Build. Mater., 26(1), 583-590. https://doi.org/10.1016/j.conbuildmat.2011.06.061
- Williams, T., & Miknis, F. (1998). Use of Environmental SEM to study asphalt-water interactions. Journal of materials in Civil Engineering, 10(2), 121-124. https://doi.org/10.1061/(ASCE)0899-1561(1998)10:2(121)
- Way GB. (1998). OGFC Meets CRM-Where the Rubber Meets the Rubber-12 Years of the durable success. The Asphalt Conference, Atlanta, Georgia.
- Xiao, F., Zhao, W., & Amirkhanian, S. N. (2009). Fatigue behavior of rubberized asphalt concrete mixtures containing warm asphlt additives. Construction and Building Materials, 23(10), 3144-3151. https://doi.org/10.1016/j.conbuildmat.2009.06.036
- Xiao, F., Punith, V. S., & Amirkhanian, S. N. (2012). Effects of non-foaming WMA additives on asphalt binders at high performance temperatures. Fuel, 94, 144-155. https://doi.org/10.1016/j.fuel.2011.09.017