DOI QR코드

DOI QR Code

Surface Characteristics based on Material and Process Changes in Surface Treatment using Fast Tool Servo

FTS를 이용한 나노표면개질공정의 공정변화와 소재에 따른 표면특성

  • Kim, Mi Ru (Department of Nano Fusion Technology, Pusan National University) ;
  • Lee, Deug Woo (Department of Nanomechatronics Engineering, Pusan National University) ;
  • Lee, Seung Jun (Interdisciplinary Department for Innovative Manufacturing Engineering, Pusan National University) ;
  • Liang, Li (Department of Nano Fusion Technology, Pusan National University) ;
  • Kim, Jong Man (Department of Nano Energy Engineering, Pusan National University) ;
  • Jang, Nam-Su (Department of Nano Fusion Technology, Pusan National University)
  • Received : 2015.07.30
  • Accepted : 2015.11.18
  • Published : 2015.12.15

Abstract

A treatment for improving the characteristics of a surface is very important in increasing the life of machine parts. Many studies have been carried out on the surface characteristics after such treatments. For enhanced eco-technology, an alternative to a conventional chemical surface treatment process is essential. Ultrasonic nano-crystal surface modification (UNSM) technology is a physical environmentally friendly surface treatment method. This technology was developed in domestic and currently being used. As the mechanism of UNSM technology, a ball tip attached to an ultrasonic vibration device strikes the metal surface at nearly 20,000 times per second. The resulting modified surface layer improves the surface characteristics. This paper describes a self-developed fast tool servo system applied to the UNSM process as a vibration module within a high-frequency bandwidth. After describing the surface modification process based on the material and process changes, the surface characteristics are compared.

Keywords

References

  1. Suh, C. M., Kim, S. H., 2008, Effect of Static Load Level of Ultrasonic Nanocrystal Surface Modification Technology on Fatigue Characteristics of SKD61, Journal of Ocean Engineering and Technology, 22:2 99-105.
  2. Nachman, G., 1999, Shot Peening-past, Present, and Future, International Conference on Shot Peening; Shot peening present & future, 1-4.
  3. Pyoun, Y. S., Cho, I. S., Hong, J. H., Lee, C. S., Park, I. K., Seo, C. M., Cho, I. H., Kim, C. S., 2007, Application of Ultrasonic Nano Crystal Surface Modification Technology for Increasing the Fatigue Strength, Weight Reduction and Decreasing the Friction Loss, Proc. of KSAE Symposium, 44-53.
  4. Schulze, V., 2003, Characteristics of Surface Layers Produced by Shot Peening, Proceeding of International Conference on Shot Peening ICSP-8 in Garmisch-partenkirchen DGM., 145-160.
  5. Mader, S., Klocke. F., 2005, Fundamentals of the Deep Rolling of Compressor Blades for Turbo Aircraft Engineers, Proceeding of Modelling and Simulation ICSP-9., 125-130.
  6. Altenberger, I., 2005, Deep Rolling the Past, the Present and the Future, International Conference on Shot Peening,144-155.
  7. CURTISS-WRIGHT, n.d., viewed 16 October 2014,
  8. Prevey, P. S., Jayaraman, N., Cammett, J., 2005, Overview of Low Plasticity Burnishing for Mitigation of Fatigue Damage Mechanisms, International Conference on Shot Peening, 267-272.
  9. Suh, C. M., Pyoun, Y. S., Cho, I. H., Baek, U. B., 2011, UNSM Surface Technology for Manufacturing and Remanufacturing Torsion Bars for Crawler Vehicles, Journal of Ocean Engineering and Technology, 25:6 80-85. https://doi.org/10.5574/KSOE.2011.25.6.080
  10. Lee, S. J., Lee, D. W., Kim, J. M., Lee, S. M., Kim, M. R., Jang, N. S., 2014, A study on Process Characteristics Using Fast Tool Servo based Surface Texturing, Journal of the Korean Society for Precision Engineerin, 31:12 1127-1132. https://doi.org/10.7736/KSPE.2014.31.12.1127
  11. Lee, S. J., Lee, D. W., Lee, S. M., Kim, M. R., Li, L., 2015, Characteristics of FTS according to Leaf-spring Designs, Proc. of KSPE Spring Conference. 1047-1047.
  12. Pyoun, Y. S., Park, J. H., Cho, I. H., Kim, C. S., Suh, C. M., 2009, A Study on the Ultrasonic Nano Crystal Surface Modification(UNSM) Technology and It's Application, Transactions of the Korean Society of Mechanical Engineers-A, 33:3 190-195. https://doi.org/10.3795/KSME-A.2009.33.3.190
  13. Kim, K. S., 2002, A Study on the Surface Treatment of Injection Mold and Die using Ultrasonic Micro-burnishing Process, A Thesis for a Master, Sunmoon University, Republic of Korea.