Journal of the Architectural Institute of Korea Structure & Construction (대한건축학회논문집:구조계)

Architectural Institute of Korea (대한건축학회)
권호 표지
DOI QR코드

DOI QR Code

The Strut-Tie Models of Reinforced Concrete Structure considering Multi-loads Case

다하중 경우를 고려한 철근콘크리트 구조물의 스트럿-타이 모델

  • 박경임 (경상대학교 대학원 건축공학과) ;
  • 이상진 (경상대학교 건축공학과)
  • Received : 2013.10.06
  • Accepted : 2014.04.09
  • Published : 2014.04.25
⟨ Previous Next ⟩

Abstract

This paper provides optimal strut-tie models (STM) of reinforced concrete (RC) structures produced by using topology optimization (TO) technique with multi-load case. The STM approach has been widely used to design the so-called D-region of RC structures where strain distributions appear to be highly nonlinear. However the conventional STM design approach requires the intuition and experiences of structural engineers to produce a proper design for D-region especially in case of complex geometries or/and load conditions. TO techniques were then introduced to make the design process easier. But most cases have been dealt with single-load case although the multi-load case should be considered for the STM design in engineering practice. Therefore, TO technique with the multi-load case is introduced to deal with the STM design of RC structures. From numerical results, it is found to be that the TO technique with multi-load case can produce new layouts of STM and they can be effectively used for the design of STM of RC structures.

Keywords

References

  1. Schlaich J., Schaefer K., Jennewein M., 1987, Toward a Consistent Design of Structural Concrete, PCI Journal, Vol.32, p.p.74-150.
  2. CSA Technical Committee A23.3, 1984, Design of Concrete Structures CAN3-A23.3-M84, Canadian Standards Association, Rexdale, Ontario.
  3. Comie Euro-International du Beton, 1993, CEB-FIP Model Code 1990, Thomas Telford Services, Ltd., London.
  4. AASHTO, 1994, AASHTO LRFD Bridge Specifications, American Association of State Highway and Transportation Officials, 1st ed., Washington, DC.
  5. 한국콘크리트학회, 2007, 콘크리트 구조설계기준.
  6. Ritter W., 1899, Die Bauweise Hennebique(The Hennebique System), Schweizerische Bauzeitung, Bd. XXXIII, No. 7.
  7. Morsch E., 1909, Concrete-steel construction, McGraw-Hill, New York.
  8. Liang Q.Q., Xie Y.M., Steven G.P.., 2000, Topology optimization of strut-and-tie models in reinforced concrete structures using an evolutionary procedure, ACI Structural Journal, Vol.97, p.p.322-30.
  9. Ali M.A., White R. N., 2001, Automatic generation of truss model for optimal design of reinforced concrete structures, ACI Structural Journal, Vol.98, p.p. 431-42.
  10. Ling Q.Q., 2005, Performance-based optimization of structures theory and applications, Spon Press.
  11. Liang Q.Q., Xie Y.M., Steven G.P., 2001, Generating optimal strut-and-tie models in prestressed concrete beams by performance-based optimization, ACI Structural Journal, Vol.98, p.p.226-32.
  12. Liang Q.Q., Uy B., Steven G.P.., 2002, Performance-based optimization for strut-tie modeling of structural concrete, Journal of Structural Engineering, Vol.128, p.p.815-23. https://doi.org/10.1061/(ASCE)0733-9445(2002)128:6(815)
  13. Bruggi M, 2009, Generation strut-and-tie patterns for reinforced concrete structures topology optimization, Computers and Structures, Vol.87. p.p.1483-95. https://doi.org/10.1016/j.compstruc.2009.06.003
  14. Kwak H-G, Noh S-H, 2006, Determination of strut and tie models using evolutionary structural optimization, Engineering Structural, Vol.28, p.p.1440-49. https://doi.org/10.1016/j.engstruct.2006.01.013
  15. 곽효경, 양규영, 신동규, 2011, 점진적 구조 최적화 기법을 이용한 철근 콘크리트 구조물의 전단 해석, 한국전산구조공학회 논문집, Vol.24, p.p.319-328.
  16. 이동규, 신수미, 2008, 철근콘크리트 구조물의 스트럿-타이 모델 설계를 위한 전산모사 최적위상 구현, 대한건축학회논문집, Vol.24, p.p.19-26.
  17. 한국콘크리트학회, 2007, 콘크리트 구조부재의 스트럿-타이 모델 설계 예제집, 기문당.
  18. 이상진, 2003, 저차유한요소를 이용한 다하중 경우를 가지는 평면구조물의 위상최적화, 한국전산구조공학회 논문집, Vol. 16, p.p. 59-68.
  19. ACI Committee 318-05, 2004, Building Code Requirements for structural Concrete(ACI 318-05) and Commentary (ACI 318R-05), American Concrete Institute, Michigan, USA, p.355.
  20. Victoria, M., M. Querin, O., Marti, P., 2011, Generation od strut-and-tie models by topology design using different material properties in tension and compression, Struct Multidisc Optim, Vol.44, p.p.247-258. https://doi.org/10.1007/s00158-011-0633-z
  21. Sigmund O., 2001, A 99 line topology optimization code written in matlab, Struct. Multidisc. Optim., Vol.21, p.p.120-127 https://doi.org/10.1007/s001580050176
  22. 이상진, 박경임, 2013, 구조물의 위상최적화를 위한 Matlab 코드, 대한건축학회논문집, Vol.29, p.p.11-18.