한국군사과학기술학회지 (Journal of the Korea Institute of Military Science and Technology)

  • 제17권4호
  • /
  • Pages.413-421
  • /
  • 2014
  • /
  • 1598-9127(pISSN)
  • /
  • 2636-0640(eISSN)
한국군사과학기술학회 (The Korea Institute of Military Science and Technology)
권호 표지
DOI QR코드

DOI QR Code

Ti-6Al-4V 합금의 단시간 고온 노출 시 모재 및 용접부의 인장강도 특성

Effects on Tensile Strength of Base and Weld Metal of Ti-6Al-4V Alloy in Short Time Exposure to High Temperature

  • 채병찬 (국방과학연구소 제1기술연구본부)
  • Chae, Byoung-Chan (The 1st Research and Development Institute, Agency for Defense Development)
  • 투고 : 2014.03.24
  • 심사 : 2014.06.13
  • 발행 : 2014.08.05
PDF 다운로드
⟨ 이전 논문 다음 논문 ⟩

초록

Since the structural temperature of a flight vehicle flying at high speed rises rapidly due to aerodynamic heating, it is necessary for optimum structural design to obtain proper material properties at high temperature by taking into account of its operational environment. For a special alloy, analysis data on strength change due to exposure time to high temperature are very limited, and most of them are for an exposure time longer than 30 minutes for long term operations. In this study, base and weld metal samples of Ti-6Al-4V alloy had been prepared and high temperature tensile tests with induction heating were performed, and then high temperature strength characteristics and strength recovery characteristics through cooling have been analyzed. Pre-tests to determine maximum heating rate were performed, and response characteristics for temperature control were confirmed. As a result, high temperature tensile strength appeared to be lower than that of room temperature, but it was higher than that of high temperature of 30 minite exposure listed in MMPDS. In strength recovery through cooling Ti-6Al-4V alloy has shown higher recovery rate compared with other alloys.

키워드

참고문헌

  1. H. Rosenberg, H. Cox, E. Erbin, "Stress Corrosion and Titanium Alloy Design for High Temperature Applications," Aircraft Design and Technology Meeting, AIAA 1965-764.
  2. J. C. Ekvall, R. A. Rainen, D. J. Chellman, "Elevated Temperature Aluminum Alloys for Advanced Fighter Aircraft," 30th Structures, Structural Dynamics and Materials Conference, AIAA 1989-1407.
  3. Robert A. Edahl, Jr. and Marcia S. Domack, "Effect of Thermal Exposure on the Tensile Properties of Aluminum Alloys for Elevated Temperature Service," NASA/TP-2004-212988.
  4. David L. Ellis, "Effects of Long Term Thermal Exposure on Chemically Pure(CP) Titanium Grade 2 Room Temperature Tensile Properties and Microstructure," NASA/TM-2007-214968.
  5. Howard L. Price, "Tensile Properties of 6Al-4V Titanium-alloy Sheet under Rapid Heating and Constant Temperature Conditions," NASA/TN-D-121.
  6. Matthew J. Donachie, Jr., "Titanium a Technical Guide," American Society for Metals, Second Edition.
  7. Metals Handbook, "Properties and Selection ; Stainless Steels, Tool Materials and Special Purpose Metals," American Society for Metals, Vol. 3, Ninth Edition.
  8. ASTM, "Standard Test Methods for Tension Testing of Metallic Materials," American Society for Testing and Materials, E8/E8M-11.
  9. FAA, "Metallic Materials Properties Development and Standardization," Fedaral Aviation Administration, MMPDS-01, 2003.