DOI QR코드

DOI QR Code

Influence of pinching effect of exterior joints on the seismic behavior of RC frames

  • Favvata, Maria J. (Department of Civil Engineering, Section of Structural Engineering, Democritus University of Thrace) ;
  • Karayannis, Chris G. (Department of Civil Engineering, Section of Structural Engineering, Democritus University of Thrace)
  • 투고 : 2013.05.17
  • 심사 : 2013.09.22
  • 발행 : 2014.01.25

초록

Nonlinear dynamic analyses are carried out to investigate the influence of the pinching hysteretic response of the exterior RC beam-column joints on the seismic behavior of multistory RC frame structures. The effect of the pinching on the local and global mechanisms of an 8-storey bare frame and an 8-storey pilotis type frame structure is evaluated. Further, an experimental data bank extracted from literature is used to acquire experimental experience of the range of the real levels that have to be considered for the pinching effect on the hysteretic response of the joints. Thus, three different cases for the hysteretic response of the joints are considered: (a) joints with strength and stiffness degradation characteristics but without pinching effect, (b) joints with strength degradation, stiffness degradation and low pinching effect and (c) joints with strength degradation, stiffness degradation and high pinching effect. For the simulation of the beam-column joints a special-purpose rotational spring element that incorporates the examined hysteretic options developed by the authors and implemented in a well-known nonlinear dynamic analysis program is employed for the analysis of the structural systems. The results of this study indicate that the effect of pinching on the local and global responses of the examined cases is not really significant at early stages of the seismic loading and especially in the cases when strength degradation in the core of exterior joint has occurred. Nevertheless in the cases when strength degradation does not occur in the joints the pinching may increase the demands for ductility and become critical for the columns at the base floor of the frame structures. Finally, as it was expected the ability for energy absorption was reduced due to pinching effect.

키워드

참고문헌

  1. ACI Committee 318-05 (2005), Building code requirements for reinforced concrete and commentary (ACI 318-05), American Concrete Institute, Detroit.
  2. Belarbi, A. and Hsu, T.T.C. (1995), "Constitutive laws of softened concrete in biaxial tension-compression", ACI Struct. J., 92(5), 562-573.
  3. Biddah, A. and Ghobarah, A. (1999), "Modelling of shear deformation and bond slip in reinforced concrete joints", Struct. Eng. Mech., 7(4), 413-432. https://doi.org/10.12989/sem.1999.7.4.413
  4. Calvi, G.M., Magenes, G. and Pampanin, S. (2002), "Relevance of beam-column joint damage and collapse in RC frame assessment", J. Earthq. Eng., 6(1), 75-100. https://doi.org/10.1080/13632460209350411
  5. CEB - FIP (1993), Model Code 1990, Thomas Telford, London.
  6. CEN (2004), Eurocode 8: Design of Structures for earthquake resistance - Part I: General rules, seismic actions and rules for Building, EN 1998-1, Brussels.
  7. Dimakopoulou, V., Fragiadakis, M. and Spyrakos, C. (2013), "Influence of modeling parameters on the response of degrading systems to near-field ground motions" Eng. Struct., 53, 10-24. https://doi.org/10.1016/j.engstruct.2013.03.008
  8. Ehsani, M.R. and Wight, J.K. (1985), "Exterior reinforced concrete beam-to-column connections subjected to earthquake-type loading", ACI J., 82, 492-499.
  9. Eligehausen, R., Popov, E.P. and Bertero, V.V. (1983), "Behavior of deformed bars anchored at interior joints under seismic excitations", Earthquake Engineering: Fourth Canadian Conference, Vancouver : Univ. of British Columbia, 70-80.
  10. Erberik, M.A., Sucuoglou, H. and Acun, B. (2012), "Inelastic displacement response of RC systems with cyclic deterioration - an energy approach", J. Earthq. Eng., 16, 937-962. https://doi.org/10.1080/13632469.2012.685210
  11. Favvata, M.J. (2006), "Investigation of the seismic response and performance of multistory reinforced concrete structures. Special simulation of joints - Interaction of structures", Ph.D. Dissertation, Democritus University of Thrace, Xanthi, Greece.
  12. Favvata, M.J., Izzuddin, B.A. and Karayannis, C.G. (2008), "Modelling exterior beam-column joints for seismic analysis of RC frames structures", Earthq. Eng. Struct. Dyn., 37, 1527-1548. https://doi.org/10.1002/eqe.826
  13. Favvata, M., Karayannis, C. and Liolios, A. (2009), "Influence of exterior joint effect on the inter-story pounding interaction of structures", Struct. Eng. Mech., 33(2), 113-136. https://doi.org/10.12989/sem.2009.33.2.113
  14. Fleury, F., Reynouard, J.M. and Merabet, O. (1999), "Finite element implementation of a steel-concrete bond law for non-linear analysis of beam-column joints subjected to earthquake type loading", Struct. Eng. Mech., 7(1), 35-52. https://doi.org/10.12989/sem.1999.7.1.035
  15. Ghobarah, A. and Biddah, A. (1999), "Dynamic analysis of reinforced concrete frames including joint shear deformation", Eng. Struct., 21, 971-987. https://doi.org/10.1016/S0141-0296(98)00052-2
  16. Hakuto, S., Park, R. and Tanaka H. (2000), "Seismic load tests on interior and exterior beam-column joints with substandard reinforcing details", ACI Struct. J., 97 (1), 11-25.
  17. Hsu, T.T.C. (1993), Unified Theory of Reinforced Concrete, CRC Press Inc.
  18. Huang, Z. and Foutch, D.A. (2009), "Effect of hysteresis type on drift limit for global collapse of moment frame structures under seismic loads", J. Earthq. Eng., 13, 939-964. https://doi.org/10.1080/13632460902859144
  19. Ibarra, L.F., Medina, R.A. and Krawinkler, H. (2005), "Hysteretic models that incorporate strength and stiffness deterioration", Earthq. Eng. Struct. Dyn., 34, 1489-1511. https://doi.org/10.1002/eqe.495
  20. Izzuddin, B.A. (1991), Nonlinear Dynamic Analysis of Framed Structures, Department of Civil Engineering, Imperial College, University of London.
  21. Izzuddin, B.A., Karayannis, C.G. and Elnashai, A.S. (1994), "Advanced nonlinear formulation for reinforced concrete frames", J. Struct. Eng.- ASCE, 120(10), 2913-2935. https://doi.org/10.1061/(ASCE)0733-9445(1994)120:10(2913)
  22. Karayannis, C.G., Favvata, M.J. and Kakaletsis, D.J. (2011), "Seismic behaviour of infilled and pilotis RC frame structures with beam-column joint degradation effect", Eng. Struct., 33(10), 2821-2831. https://doi.org/10.1016/j.engstruct.2011.06.006
  23. Karayannis, C.G., Chalioris, C.E. and Sideris, K.K. (1998), "Effectiveness of RC beam-column connection repair using epoxy resin injections", J. Earthq. Eng., 2(2), 217-240.
  24. Karayannis, C.G., Chalioris, C.E. and Sirkelis, G.S. (2008), "Local retrofit of exterior RC beam-column joints using thin RC jackets - an experimental study", Earthq. Eng. Struct. Dyn., 37, 727-746. https://doi.org/10.1002/eqe.783
  25. Karayannis, C.G., Izzuddin, B.A. and Elnashai, A.S. (1994), "Application of adaptive analysis to reinforced concrete frames", J. Struct. Eng. - ASCE, 120(10), 2936-2957.
  26. Karayannis, C.G., Sirkelis, G.S. and Chalioris, C.E. (2006), "Seismic performance of RC beam-columns joints retrofitted using light RC jacket-Experimental study", Proceedings of the 1st European Conference on Earthquake Engineering and Seismology, Geneva, Switzerland, September.
  27. Karayannis, C.G., Sirkelis, G.S., Chalioris, C.E. and Mavroeidis, P. (2003), "External RC joints with continuous spiral reinforcement. Experimental investigation", Proceedings of the 14th Greek Conference on Concrete, Kos, Greece, October. (in Greek)
  28. Kim, J. and LaFave, J.M. (2007), "Key influence parameters for the joint shear behavior of reinforced concrete (RC) beam-column connections", Eng. Struct., 29(10), 2523-2539. https://doi.org/10.1016/j.engstruct.2006.12.012
  29. Kunnath, S.K., Mander, J.B. and Fang, L. (1997), "Parameter identification for degrading and pinched hysteretic structural concrete systems", Eng. Struct., 19(3), 224-232. https://doi.org/10.1016/S0141-0296(96)00058-2
  30. Kwak, H.G., Kim, S.P. and Kim, J.E. (2004), "Nonlinear dynamic analysis of RC frames using cyclic moment-curvature relation", Struct. Eng. Mech., 17(3-4), 357-378. https://doi.org/10.12989/sem.2004.17.3_4.357
  31. Kyrkos, M.T. and Anagnostopoulos, S.A. (2011) "An assessment of code designed, torsionally stiff, asymmetric steel buildings under strong earthquake excitations", Earthq. Struct., 2(2), 109-126. https://doi.org/10.12989/eas.2011.2.2.109
  32. Lima, C., Martinelli, E. and Faella, C. (2012), "Capacity models for shear strength of exterior joints in RC frames: state-of-the-art and synoptic examination", Bull. Earthq. Eng, 10, 967-983. https://doi.org/10.1007/s10518-012-9340-4
  33. Lowes, L.N. and Altoontash, A. (2003), "Modeling reinforced-concrete beam-column joints subjected to cycling loading", J. Struct. Eng. - ASCE, 129(12), 1686-1697. https://doi.org/10.1061/(ASCE)0733-9445(2003)129:12(1686)
  34. Lu, X., Urukap, T.H., Li, S. and Lin, F. (2012), "Seismic behavior of interior RC beam-column joints with additional bars under cyclic loading", Earthq. Struct., 3(1), 37-57. https://doi.org/10.12989/eas.2012.3.1.037
  35. NZS 3101 (1995), Code of practice for the design of concrete structures, Standard Association of New Zealand, Wellington, Parts 1 and 2.
  36. Pampanin, S., Magenes, G. and Carr, A. (2003), "Modelling of shear hinge mechanism in poorly detailed RC beam-column joints", Proceedings of the Fib Symposium on Concrete Structures in Seismic Regions, Athens, Greece, May.
  37. Pampanin, S., Calvi, G.M. and Moratti, M. (2002), "Seismic behaviour of RC beam-column joints designed for gravity only", Proceedings of the 12th European Conference on Earthquake Engineering, London.
  38. Pantelides, C.P., Hansen, J., Nadauld, J.D. and Reaveley, L.D. (2002), "Assessment of reinforced concrete building exterior joints with substandard details", Peer Report, Pacific Earthquake Engineering Research Centre, University of California, Research Report 2002/18, University of California, Berkeley, May.
  39. Park, S. and Mosalam, K. (2009), "Steel strength models of exterior beam-column joints without transverse reinforcement", Peer Report, Pacific Earthquake Engineering Research Centre - University of California, Research Report 2009/106, University of California, Berkeley, November.
  40. Paulay, T. and Priestley, M.J.N. (1992), Seismic Design of Reinforced Concrete and Masonry Buildings, John Wiley & Sons.
  41. Sengupta, P. and Li, B. (2013), "Modified Bouc-Wen model for hysteresis behavior of RC beam-column joints with limited transverse reinforcement", Eng. Struct., 46, 392-406. https://doi.org/10.1016/j.engstruct.2012.08.003
  42. Sharma, A., Eligehausen, R. and Reddy G.R. (2011), "A new model to simulate joint shear behavior of poorly detailed beam-column connections in RC structures under seismic loads, Part I: exterior joints", Eng. Struct., 33, 1034-1051. https://doi.org/10.1016/j.engstruct.2010.12.026
  43. Shima, H., Chou, L. and Okamura, H. (1987), "Micro and macro models for bond in reinforced concrete", J. Fac. Eng. Univ. Tokyo B, 39(2), 133-194.
  44. Shin, M. and LaFave, J.M. (2004), "Modeling of cyclic joint shear deformation contributions in RC beam-column connections to overall frame behaviour", Struct. Eng. Mech., 18(5), 645-669. https://doi.org/10.12989/sem.2004.18.5.645
  45. Takeda, T., Sozen, M.A. and Nielsen, N.N. (1970), "Reinforced concrete response to simulated earthquakes", J. Struct. Eng. - ASCE, 96(12), 2557-2573.
  46. Tsonos, G.A. (2002), "Seismic repair of exterior R/C beam-to-column joints using two-sided and three-sided jackets", Struct. Eng. Mech., 13(1), 17-34. https://doi.org/10.12989/sem.2002.13.1.017
  47. Tsonos, A.G. (2007), "Cyclic load behavior of RC beam-column subassemblages of modern structures", ACI Struct. J., 104(4), 468-478.
  48. Tsonos, A.G., Tegos, I.A. and Penelis, G.Gr. (1992), "Seismic resistance of Type 2 exterior beam-column joints reinforce with inclined bars" ACI Struct. J., 89(1), 3-12.
  49. Youssef, M. and Ghobarah, A. (2001), "Modeling of RC beam-column joints and structural walls", J. Earthq. Eng., 5(1), 93-111.

피인용 문헌

  1. Evaluation of performance of non-invasive upgrade strategy for beam-column sub-assemblages of poorly designed structures under seismic type loading vol.45, pp.11, 2016, https://doi.org/10.1002/eqe.2730
  2. Cyclic behavior of in-situ exterior beam-column subassemblies with cold joint in column vol.132, 2017, https://doi.org/10.1016/j.engstruct.2016.12.001
  3. Seismic performance of non-invasive single brace made of steel and shape memory alloy for retrofit of gravity load designed sub-assemblages vol.143, 2017, https://doi.org/10.1016/j.engstruct.2017.04.024
  4. High-strength concrete exterior beam-column joints with high-yield strength steel reinforcements vol.145, 2017, https://doi.org/10.1016/j.engstruct.2017.05.024
  5. Nonlinear seismic analysis of a super 13-element reinforced concrete beam-column joint model vol.11, pp.5, 2016, https://doi.org/10.12989/eas.2016.11.5.905
  6. Seismic retrofit design method using friction damping systems for old low- and mid-rise regular reinforced concrete buildings vol.146, 2017, https://doi.org/10.1016/j.engstruct.2017.05.031
  7. Finite Element Analysis (FEA) for the Beam-Column Joint Subjected to Cyclic Loading Was Performed Using ANSYS vol.07, pp.08, 2016, https://doi.org/10.4236/cs.2016.78138
  8. Cyclic behaviour of interior beam-column joints reinforced with plain bars vol.44, pp.9, 2015, https://doi.org/10.1002/eqe.2521
  9. Design considerations for interior RC beam–column joint with additional bars vol.98, 2015, https://doi.org/10.1016/j.engstruct.2015.04.021
  10. Shear strength criteria for design of RC beam–column joints in building codes pp.1573-1456, 2018, https://doi.org/10.1007/s10518-018-0492-8
  11. Analytical Investigations of Reinforced Concrete Beam–Column Joints Constructed Using High-Strength Materials pp.1559-808X, 2020, https://doi.org/10.1080/13632469.2018.1453403
  12. Simplified assessment of the need for the explicit model of RC beam-column joints instead of the rigid model pp.14644177, 2019, https://doi.org/10.1002/suco.201800140
  13. Modelling beam-to-column joints in seismic analysis of RC frames vol.12, pp.1, 2014, https://doi.org/10.12989/eas.2017.12.1.119
  14. Nonlinear response of r.c. framed buildings retrofitted by different base-isolation systems under horizontal and vertical components of near-fault earthquakes vol.12, pp.1, 2014, https://doi.org/10.12989/eas.2017.12.1.135
  15. An ESED method for investigating seismic behavior of single-layer spherical reticulated shells vol.13, pp.5, 2014, https://doi.org/10.12989/eas.2017.13.5.455
  16. Analytical prediction of seismic behavior of RC joints and columns under varying axial load vol.174, pp.None, 2014, https://doi.org/10.1016/j.engstruct.2018.07.103
  17. Seismic Behavior of RC Beam Column Joints with 600 MPa High Strength Steel Bars vol.10, pp.13, 2014, https://doi.org/10.3390/app10134684
  18. Failure mechanisms and cracking performance of T-shaped SCC beam-column connections at top floor: Test results and FE modeling vol.28, pp.None, 2014, https://doi.org/10.1016/j.istruc.2020.09.051
  19. Experimental Study on the Shear Performance of Steel-Truss-Reinforced Concrete Beam-Column Joints vol.2021, pp.None, 2014, https://doi.org/10.1155/2021/5580581
  20. A regression model for predicting the shear strength of RC knee joint subjected to opening and closing moment vol.41, pp.None, 2014, https://doi.org/10.1016/j.jobe.2021.102727
  21. Development of limit states for seismic fragility assessment of piloti-type structures verified with observed damage data vol.251, pp.no.pb, 2014, https://doi.org/10.1016/j.engstruct.2021.113562
  22. An explicit solution for the effect of earthquake incidence angles on seismic ductility demand of structures using Bouc-Wen model vol.153, pp.None, 2014, https://doi.org/10.1016/j.soildyn.2021.107085