Steel and Composite Structures

  • 제17권6호
  • /
  • Pages.951-965
  • /
  • 2014
  • /
  • 1229-9367(pISSN)
  • /
  • 1598-6233(eISSN)
테크노프레스 (Techno-Press)
권호 표지
DOI QR코드

DOI QR Code

Inelastic response of wide flange steel beams curved by symmetrical weak axis bending using two-point loads

  • Gergess, Antoine N. (Department of Civil Engineering, University of Balamand) ;
  • Sen, Rajan (University of South Florida)
  • 투고 : 2012.05.11
  • 심사 : 2014.04.30
  • 발행 : 2014.12.25
⟨ 이전 논문 다음 논문 ⟩

초록

Point bending is commonly used for cambering and curving steel girders to large radii. In this system, a hydraulic ram or press is used to apply concentrated loads at selected points to obtain the required vertical (cambering) or horizontal (curving) curved profile from induced permanent deformations. This paper derives closed form solutions that relate loads to permanent deformations for horizontally curving wide flange steel beams based on their post-yield response. These solutions are presented in a parametric form to identify the relationship between key variables and their impact on the accuracy of the curving operation. It is shown that point bending could yield parabolic curved profiles that are within 1% of a desired circular curve if the span length to radius of curvature ratio (L / R) is less than 1.5 and the point loads are spaced at one third the beam length. Safe limits are then established on loads, strains and curvatures to avoid damaging the steel section. This leads to optimization of the point bending operation for inducing a circular profile in wide flange steel beams of any size.

키워드

참고문헌

  1. AISC (2011), Steel Construction Manual, (14th Edition), American Institute of Steel Construction, USA.
  2. Alwood, T.A. (2006), "What engineers should know about bending steel", Modern Steel Construction (MSC), May, pp. 24-26.
  3. Barnshaw, R. (2009), "Bending considerations in steel construction", Modern Steel Construction (MSC), October, pp. 42-44.
  4. Bjorhovde, R. (2006), "Cold bending of wide-flange shapes for construction", Am. Inst. Steel Construct. (AISC), Eng. J., 4(43), 271-286.
  5. Brockenbrough, R.L. (2003), "MTR survey of plate material used in structural fabrication", Am. Inst. Steel Construct. (AISC), Eng. J., 40(1), 42-49.
  6. Craig, R.R. (2011), Mechanics of Materials, (3rd Edition), John Wiley and Sons, Inc.
  7. Gergess, A. and Sen, R. (2010), "Post-yield response of cold-cambered wide-flange steel beams", J. Construct. Steel Res., 65(10), 1155-1163.
  8. Gergess, A. and Sen, R. (2011), "Optimized solution for bending wide-flange steel beams about their weak axis", Modern Method. Adv. Struct. Eng. Construct., Singapore, pp. 865- 870.
  9. King, M. (2005), "Around the bend: What detailers should know about bending steel", Modern Steel Construction (MSC), May, pp. 61-63.
  10. Lange, J. and Grages, H. (2009), "Influence of the Bauschinger effect on the deflection behaviour of cambered steel and steel concrete composite beams", Struct. Eng. Int., 19(4), 410-414. https://doi.org/10.2749/101686609789847064
  11. Mansouri, H., Monshi, A. and Hadavinia, H. (2004), "Effect of local induction heat treatment on the induced residual stresses in the web region of a welded rail", J. Strain Anal. Eng. Des., 39(3), 271-283. https://doi.org/10.1243/030932404323042696
  12. Moen, C. and Via, E.C. (2011), "Cold bending fabrication - state-of-the-art, industry challenges, engineering solutions, TRB AFH70 Committee Meeting, Fabrication and Inspection of Metal Structures, Washington, D.C., USA, January.
  13. Salmon, C.G., Malhas F.A. and Johnson, J.E. (2010), Steel Structures: Design and Behavior, (5th Edition), Harper- Collins, NY, USA.
  14. Spoorenberg, R.C., Snijder, H.H. and Hoenderkamp, J.C.D. (2010), "Experimental investigation of residual stresses in roller bent wide flange steel sections", J. Construct. Steel Res., 66(6), 737-747. https://doi.org/10.1016/j.jcsr.2010.01.017
  15. White, D.W. (2008), "Structural behavior of steel", Steel Bridge Design Handbook, Chapter 6, National Steel Bridge Alliance, Chicago, IL, USA.
  16. Wong, E. and Driver, R.G. (2010), "Critical evaluation of equivalent moment factor procedures for laterally unsupported beams", Eng. J. AISC, 47(1), 1-20.