DOI QR코드

DOI QR Code

Effect of Metakaolin Content on the Properties of High Strength Concrete

  • Dinakar, P. (School of Infrastructure, Indian Institute of Technology) ;
  • Sahoo, Pradosh K. (School of Infrastructure, Indian Institute of Technology) ;
  • Sriram, G. (School of Infrastructure, Indian Institute of Technology)
  • 투고 : 2013.11.15
  • 심사 : 2013.05.30
  • 발행 : 2013.09.30

초록

This study presents the effect of incorporating metakaolin (MK) on the mechanical and durability properties of high strength concrete for a constant water/binder ratio of 0.3.MK mixtures with cement replacement of 5, 10 and 15 % were designed for target strength and slump of 90 MPa and $100{\pm}25mm$. From the results, it was observed that 10 % replacement level was the optimum level in terms of compressive strength. Beyond 10 %replacement levels, the strength was decreased but remained higher than the control mixture. Compressive strength of 106 MPa was achieved at 10 % replacement. Splitting tensile strength and elastic modulus values have also followed the same trend. In durability tests MK concretes have exhibited high resistance compared to control and the resistance increases as the MK percentage increases. This investigation has shown that the local MK has the potential to produce high strength and high performance concretes.

키워드

참고문헌

  1. Abbas, R., Abo-El-Enein, S. A., & Ezzat, E. S. (2010). Properties and durability of metakaolin blended cements: Mortar and concrete. Materiales De Construccion, 60, 33-49.
  2. Abdul, R. H., & Wong, H. S. (2005). Strength estimation model for high-strength concrete incorporating metakaolin and silica fume. Cement Concrete Research, 35(4), 688-695. https://doi.org/10.1016/j.cemconres.2004.05.040
  3. ASTM C. (2006a). Standard test method for density, absorption, and voids in hardened concrete, 642. Philadelphia, PA: Annual Book of ASTM Standards.
  4. ASTM C. (2006b). Standard test method for electrical indication of concrete's ability to resist chloride ion penetration, 1202. Philadelphia, PA: Annual Book of ASTM Standards.
  5. ASTM C. (2006c). Standard test method for static modulus of elasticity and poisson's ratio of concrete in compression, 469. Philadelphia, PA: Annual Book of ASTM Standards.
  6. Badogiannis, E., & Tsivilis, S. (2009). Exploitation of poor Greek kaolins: Durability of metakaolin concrete. Cement & Concrete Composites, 31(2), 128-133. https://doi.org/10.1016/j.cemconcomp.2008.11.001
  7. Bai, J., Wild, S., & Sabir, B. B. (2002). Sorptivity and strength of air cured and water cured PC-PFA-MK concrete and the influence of binder composition on carbonation depth. Cement and Concrete Research, 32(11), 1813-1821. https://doi.org/10.1016/S0008-8846(02)00872-4
  8. Basu, P. C. (2003). High performance concrete. In Proceedings INAE national seminar on engineered building materials and their performance (pp. 426-450).
  9. Basu, P. C., Mavinkurve, S., Bhattacharjee, K. N., Deshpande, Y., & Basu, S. (2000). High reactivity metakaolin: A supplementary cementitious material. In Proceedings ICIAsian conference on ecstasy in concrete, 20-22 Nov, Bangalore, India (pp. 237-436).
  10. Boddy, A., Hooton, R. D., & Gruber, K. A. (2001). Long-term testing of the chloride-penetration resistance of concrete containing high-reactivity metakaolin. Cement and Concrete Research, 31, 759-765. https://doi.org/10.1016/S0008-8846(01)00492-6
  11. BS EN-12390-8. (2000). Depth of penetration of water under pressure. British Standards Institution.
  12. CEB-FIP. (1989). Diagnosis and assessment of concrete structures- state of the art report. CEB Bulletin, 192, 83-85.
  13. Dhir, R. K., & Yap, A. W. F. (1984). Superplasticized flowing concrete: durability. Magazine of Concrete Research, 36(127), 99-111. https://doi.org/10.1680/macr.1984.36.127.99
  14. DIN 1045. (1988). Beton und Stahlbeton. Koln, Germany: Beton Verlag GMBH.
  15. Dinakar, P. (2012). Design of self compacting concrete with fly ash. Magazine of Concrete Research, 64(5), 401-409. https://doi.org/10.1680/macr.10.00167
  16. Ding, Z., Zhang, D., & Yu, R. (1999). High strength composite cement. China Building & Material Science Technology, 1, 14-17.
  17. Dvorkin, L., Bezusyak, A., Lushnikova, N., & Ribakov, Y. (2012). Using mathematical modelling for design of self compacting high strength concrete with metakaolin admixture. Construction and Building Materials, 37, 851-864. https://doi.org/10.1016/j.conbuildmat.2012.04.019
  18. Gruber, K. A., Ramlochan, T., Boddy, A., Hooton, R. D., & Thomas, M. D. A. (2001). Increasing concrete durability with high-reactivity metakaolin. Cement & Concrete Composites, 23, 479-484. https://doi.org/10.1016/S0958-9465(00)00097-4
  19. Guneyisi, E., Gesoglu, M., & Mermerdas, K. (2008). Improving strength, drying shrinkage, and pore structure of concrete using metakaolin. Materials and Structures, 41, 937-949. https://doi.org/10.1617/s11527-007-9296-z
  20. Haque, M. N., & Kayali, O. (1998). Properties of high strength concrete using a fine fly ash. Cement and Concrete Research, 28(10), 1445-1452. https://doi.org/10.1016/S0008-8846(98)00125-2
  21. IS. (1987). Specification for 53 grade ordinary Portland cement, 12269. New Delhi: Bureau of Indian Standards.
  22. Khatib, J. M. (2008). Metakaolin concrete at a low water to binder ratio. Construction and Building Materials, 22(8), 1691-1700. https://doi.org/10.1016/j.conbuildmat.2007.06.003
  23. Kim, H. S., Lee, S. H., & Moon, H. Y. (2007). Strength properties and durability aspects of high strength concrete using Korean metakaolin. Construction and Building Materials, 21, 1229-1237. https://doi.org/10.1016/j.conbuildmat.2006.05.007
  24. Mehta, P. K., & Monteiro, P. J. (1999). Concrete: microstructure, properties, and materials. Delhi, India: Indian Concrete Institute.
  25. Nehdi, R. M., Mindness, S., & Aitcin, P. C. (1998). Rheology of high performance concrete: Effect of ultrafine particles. Cement and Concrete Research, 28(5), 687-697. https://doi.org/10.1016/S0008-8846(98)00022-2
  26. Neville, A. M. (1997). Concrete with particular properties. In Properties of concrete (pp. 653-672). Harlow, UK: Longman
  27. Pal, S. C., Mukherjee, A., & Pathak, S. R. (2001) Development of high performance concrete composites using high volume cement replacement with supplementary pozzolanic and cementitioius solid waste. In S. K. Kaushik (Ed.), Proceedings of SEC, recent developments in structural engineering (pp. 215-229). New Delhi, India: Phoenix publishing house Pvt Ltd.
  28. Parande, A. K., Ramesh Babu, B., Karthik, M. A., Kumar, K. K., & Palaniswamy, N. (2008). Study on strength and corrosion performance for steel embedded in metakaolin blended concrete/mortar. Construction and Building Materials, 22(3), 127-134. https://doi.org/10.1016/j.conbuildmat.2006.10.003
  29. Patil, B. B., & Kumbhar, P. D. (2012). Strength and durability properties of high performance concrete incorporating high reactivity metakaolin. International Journal of Modern Engineering Research, 2(3), 1099-1104.
  30. Poon, C. S., Lam, L., Kou, S. C., Wong, Y. L., & Wong, R. (2001). Rate of pozzolanic reaction of metakaolin in highperformance cement pastes. Cement and Concrete Research, 31(9), 1301-1306. https://doi.org/10.1016/S0008-8846(01)00581-6
  31. Rasiah, A. R. (1983) High strength concrete for developing countries. In: Proceedings of the first international conference on concrete technology in developing countries, Amman, Jordan.
  32. Sabir, B. B., Wild, S., & Bai, J. (2001). Metakaolin and calcined clays as pozzolans for concrete: A review. Cement & Concrete Composites, 23, 441-454. https://doi.org/10.1016/S0958-9465(00)00092-5
  33. Schiessl, P. (1988). Corrosion of steel in concrete, Report of the technical committee 60-CSC, RILEM. London, UK: Chapman and Hall.
  34. Tiwari, A. K., & Bandyopadhyay, P. (2003) High performance concrete with Indian metakaolin. In International symposium on innovative world of concrete, 19-21 September. Pune: Indian Concrete Institute.
  35. Wild, S., & Khatib, J. M. (1997). Portlandite consumption of metakaolin cement Pastes and mortars. Cement and Concrete Research, 27(1), 137-146. https://doi.org/10.1016/S0008-8846(96)00187-1
  36. Wild, S., Khatib, J. M., & Jones, A. (1996). Relative strength, pozzolanic activity and cement hydration in superplasticised metakaolin concrete. Cement and Concrete Research, 26(10), 1537-1544. https://doi.org/10.1016/0008-8846(96)00148-2
  37. Yogendran, V., Langan, B. W., Haque, M. N., & Ward, M. A. (1987). Silica fume in high strength concrete. ACI Materials Journal, 84, 124.
  38. Zain, M. F. M., Safiuddin, M. D., & Mahmud, H. (2000). Development of high performance concrete using silica fume at relatively high water-binder ratios. Cement and Concrete Research, 30(9), 1501-1505. https://doi.org/10.1016/S0008-8846(00)00359-8

피인용 문헌

  1. Stress-Strain Relationship of Ca(OH) 2 -Activated Hwangtoh Concrete vol.2014, pp.None, 2013, https://doi.org/10.1155/2014/846805
  2. Fracture characteristics of refractory composites containing metakaolin and ceramic fibers vol.7, pp.3, 2015, https://doi.org/10.1177/1687814015573619
  3. Material Performance and Animal Clinical Studies on Performance-Optimized Hwangtoh Mixed Mortar and Concrete to Evaluate Their Mechanical Properties and Health Benefits vol.8, pp.9, 2015, https://doi.org/10.3390/ma8095306
  4. Predicting Pumpability and Shootability of Crushed Aggregate Wet-Mix Shotcrete Based on Rheological Properties vol.2016, pp.None, 2013, https://doi.org/10.1155/2016/9838213
  5. Investigation on the Effectiveness of Aqueous Carbonated Lime in Producing an Alternative Cementitious Material vol.10, pp.1, 2016, https://doi.org/10.1007/s40069-016-0129-8
  6. Properties and performance of metakaolin pozzolanic cement pastes vol.129, pp.1, 2013, https://doi.org/10.1007/s10973-017-6087-9
  7. Ability of Two Dam Fine-Grained Sediments to be Used in Cement Industry as Raw Material for Clinker Production and as Pozzolanic Additional Constituent of Portland-Composite Cement vol.8, pp.6, 2013, https://doi.org/10.1007/s12649-017-9870-8
  8. Super-robust superhydrophobic concrete vol.5, pp.28, 2013, https://doi.org/10.1039/c7ta03526h
  9. Effect of Partial Replacement of Fly Ash by Metakaolin on Strength Development of Fly Ash Based Geopolymer Mortar vol.744, pp.None, 2013, https://doi.org/10.4028/www.scientific.net/kem.744.131
  10. Influence of Metakaolin, Fly Ash and Nano Silica on Mechanical and Durability Properties of Concrete vol.744, pp.None, 2013, https://doi.org/10.4028/www.scientific.net/kem.744.8
  11. High-performance self-compacting concrete with the use of coal burning waste vol.90, pp.None, 2017, https://doi.org/10.1088/1755-1315/90/1/012213
  12. Evaluation of Pozzolanic Activity for Effective Utilization of Dredged Sea Soil vol.11, pp.4, 2013, https://doi.org/10.1007/s40069-017-0215-6
  13. Properties of metakaolin-blended oil palm shell lightweight concrete vol.22, pp.7, 2013, https://doi.org/10.1080/19648189.2016.1229222
  14. Utilization of Metakaolin and Calcite: Working Reversely in Workability Aspect-As Mineral Admixture in Self-Compacting Concrete vol.2018, pp.None, 2013, https://doi.org/10.1155/2018/4072838
  15. Hydration and characteristics of metakaolin pozzolanic cement pastes vol.14, pp.2, 2013, https://doi.org/10.1016/j.hbrcj.2015.05.005
  16. Influence of Two Polymer-Based Superplasticizers (Poly-naphthalene Sulfonate, PNS, and Lignosulfonate, LS) on Compressive and Flexural Strength, Freeze-Thaw, and Sulphate Attack Resistance of Lime-Met vol.10, pp.8, 2013, https://doi.org/10.3390/polym10080824
  17. Sustainable Materials for Transportation Infrastructures: Comparison of Three Commercially-Available Metakaolin Products in Binary Cementitious Systems vol.3, pp.3, 2013, https://doi.org/10.3390/infrastructures3030017
  18. Physico-chemical properties of nano metakaolin on the characteristics of blended limestone cement vol.4, pp.1, 2019, https://doi.org/10.1007/s41024-019-0048-6
  19. Modeling the effect of silica fume on the compressive, tensile strengths and durability of NSC and HSC in various strength ranges vol.4, pp.1, 2013, https://doi.org/10.1007/s41024-019-0058-4
  20. Microstructure, thermal analysis and chloride penetration of self-compacting concrete under different conditions vol.71, pp.3, 2013, https://doi.org/10.1680/jmacr.17.00367
  21. Efeito do envelhecimento acelerado sobre as propriedades de microconcreto reforçado com fibras longas de sisal vol.19, pp.1, 2013, https://doi.org/10.1590/s1678-86212019000100289
  22. Effects of Modified Metakaolin Using Nano-Silica on the Mechanical Properties and Durability of Concrete vol.12, pp.14, 2013, https://doi.org/10.3390/ma12142291
  23. Role of recycling fine materials as filler for improving performance of concrete - a review vol.17, pp.2, 2013, https://doi.org/10.1080/14488353.2019.1626692
  24. Filler-Ability of Highly Active Metakaolin for Improving Morphology and Strength Characteristics of Recycled Aggregate Concrete vol.11, pp.4, 2013, https://doi.org/10.1007/s12633-018-0017-8
  25. Characterization of LDH (phyllosilicate/carbonate) type compounds formed in the pozzolanic reaction of phyllosilicate‐rich industrial waste vol.102, pp.8, 2013, https://doi.org/10.1111/jace.16354
  26. Corrosion behavior of reinforced concrete blended with metakaolin and slag in chloride environment vol.8, pp.6, 2013, https://doi.org/10.1080/21650373.2019.1566934
  27. Fresh and Hardened Properties of Concrete Incorporating Binary Blend of Metakaolin and Ground Granulated Blast Furnace Slag as Supplementary Cementitious Material vol.2020, pp.None, 2013, https://doi.org/10.1155/2020/8851030
  28. Comparison of Hydration of Thermally Activated Water-Washed Kaolins in Cement Mortar vol.48, pp.3, 2013, https://doi.org/10.1520/jte20190128
  29. Influence of Early-Age Curing Regimes on Late-Age Hydration of UHPC vol.9, pp.1, 2013, https://doi.org/10.1520/acem20200037
  30. Strength of Self-Compacting Concrete Containing Metakaolin and Nylon Fiber vol.498, pp.None, 2013, https://doi.org/10.1088/1755-1315/498/1/012047
  31. Characterization of Enhanced ITZ in Engineered Polypropylene Fibers for Bond Improvement vol.4, pp.2, 2013, https://doi.org/10.3390/jcs4020053
  32. A novel method to predict pozzolanic nature of concrete with sintered clay using soft computing techniques vol.872, pp.None, 2020, https://doi.org/10.1088/1757-899x/872/1/012159
  33. Incorporation of glass powder and metakaolin as cement partial replacement to improve concrete mechanical properties and increase service life vol.54, pp.21, 2013, https://doi.org/10.1177/0021998320906873
  34. Effect of using mineral admixtures and ceramic wastes as coarse aggregates on properties of ultrahigh-performance concrete vol.273, pp.None, 2013, https://doi.org/10.1016/j.jclepro.2020.123073
  35. Methodology to evaluate variations in concrete color caused by white cement substitutions and forming materials vol.53, pp.6, 2013, https://doi.org/10.1617/s11527-020-01565-x
  36. Use of zeolite and industrial waste materials in high strength concrete - A review vol.46, pp.p1, 2021, https://doi.org/10.1016/j.matpr.2020.06.329
  37. Effect of MK and SF on the concrete mechanical properties vol.42, pp.p5, 2013, https://doi.org/10.1016/j.matpr.2020.12.751
  38. Green Concrete for a Circular Economy: A Review on Sustainability, Durability, and Structural Properties vol.14, pp.2, 2021, https://doi.org/10.3390/ma14020351
  39. Efficacy of Natural Zeolite and Metakaolin as Partial Alternatives to Cement in Fresh and Hardened High Strength Concrete vol.2021, pp.None, 2013, https://doi.org/10.1155/2021/4090389
  40. Application of Extreme Gradient Boosting Based on Grey Relation Analysis for Prediction of Compressive Strength of Concrete vol.2021, pp.None, 2013, https://doi.org/10.1155/2021/8878396
  41. Use of Nondestructive Testing of Ultrasound and Artificial Neural Networks to Estimate Compressive Strength of Concrete vol.11, pp.2, 2013, https://doi.org/10.3390/buildings11020044
  42. Using Geopolymer Technology on Synthesizing Leucite Ceramics vol.13, pp.21, 2013, https://doi.org/10.3390/polym13213621
  43. Quantification the effect of microsand on the compressive, tensile, flexural strengths, and modulus of elasticity of normal strength concrete vol.16, pp.6, 2021, https://doi.org/10.1080/17486025.2019.1680884
  44. Influence of metakaolin as a partial replacement of cement on characteristics of concrete exposed to high temperatures vol.10, pp.6, 2021, https://doi.org/10.1080/21650373.2021.1877206
  45. Strength and Permeability of No-Fines Concrete Made with Supplementary Cementitious Materials vol.34, pp.1, 2013, https://doi.org/10.1061/(asce)mt.1943-5533.0004037
  46. Experimental studies of sustainable concrete modified with colloidal nanosilica and metakaolin vol.7, pp.1, 2013, https://doi.org/10.1007/s41024-021-00157-8
  47. Experimental studies of sustainable concrete modified with colloidal nanosilica and metakaolin vol.7, pp.1, 2013, https://doi.org/10.1007/s41024-021-00157-8