Transactions of Materials Processing (소성∙가공)

The Korean Society for Technology of Plasticity and materials processing (한국소성∙가공학회)
권호 표지
DOI QR코드

DOI QR Code

High Temperature Deformation Behavior of a NIMONIC 80A Ni-based Superalloy

Ni계 초내열합금 NIMONIC 80A의 고온변형거동

  • Received : 2013.06.19
  • Accepted : 2013.07.18
  • Published : 2013.08.01
Download PDF
⟨ Previous Next ⟩

Abstract

The deformation behavior of NIMONIC 80A was studied in the high temperature range of $900{\sim}1200^{\circ}C$ and for strain rates varying between 0.02 and $20s^{-1}$ via the hot compression test. Processing maps for hot working were constructed on the basis of the power dissipation efficiency using a dynamic material model. The results showed that the strength during hot compression increased with increasing strain rate and decreasing temperature. At low strains, the processing map of NIMONIC 80A did not reveal any instability domain regardless of the strain rate and temperature. However, at high strains, the processing map exhibited an instability domain at a low strain rate of $0.2s^{-1}$ and within a temperature range of $900{\sim}960^{\circ}C$. In the instability domain, the deformed microstructure exhibited shear bands and carbide precipitation while, in the safe domain, full recrystallization occurred.

Keywords

References

  1. M. Sanjari, A. Karimi Taheri, M. R. Movahedi, 2009, An Optimization Method for Radial Forging Process using ANN and Taguchi Method, Int. J. Adv. Manuf. Technol., Vol. 40, No. 7-8, pp. 776-784. https://doi.org/10.1007/s00170-008-1371-2
  2. A. Bapari, A. Najafizadeh, M. Moazeny, A. Shafyei, 2008, Simulation of Radial Forging Conditions by Third Hits Hot Compression Test, Mater. Sci. Eng. A, Vol. 491, No. 1-2, pp. 258-265. https://doi.org/10.1016/j.msea.2008.01.087
  3. N. Srinivasan, Y. V. R. K. Prasad, 1995, Hot Working Characteristics of Nimonic 75, 80A and 90 Superalloys: a Comparison using Processing Maps, J. Mater. Process. Technol., Vol. 51, No. 1-4, pp. 171-192. https://doi.org/10.1016/0924-0136(94)01602-W
  4. H. J. McQueen, N. D. Ryan, 2002, Constitutive Analysis in Hot Working, Mater. Sci. Eng., A, Vol. 322, No. 1-2, pp. 43-63. https://doi.org/10.1016/S0921-5093(01)01117-0
  5. C. M. Sellars, W. J. McG. Tegart, 1972, Hot Workability, Int. Mater. Rev., Vol. 17, No. 1, pp. 1-24. https://doi.org/10.1179/095066072790137765
  6. H. S. Jeong, J. R. Cho, H. C. Park, 2005, Microstructure Prediction of Nimonic 80A for Large Exhaust Valve during Hot Closed Die Forging, J. Mater. Process. Technol., Vol. 162-163, pp. 504-511. https://doi.org/10.1016/j.jmatprotec.2005.02.101
  7. Y. Liu, R. Hu, J. Li, H. Kou, H. Li, H. Chang, H. Fu, 2008, Deformation Characteristics of As-received Haynes 230 Nickel Base Superalloy, Mater. Sci. Eng., A, Vol. 497, No. 1-2, pp. 283-289. https://doi.org/10.1016/j.msea.2008.07.052
  8. Y. V. R. K Prasad, T. Seshacharyulu, 1998, Modelling of Hot Deformation for Microstructural Control, Int. Mater. Rev., Vol. 43, No. 6, pp. 243-258. https://doi.org/10.1179/095066098790105618
  9. J. T. Yeom, D. H. Kim, Y. S. Na, N. K. Park, 2001, Characterization of Hot Deformation Behavior of Ti-6Al-4V Alloy, Trans. Mater. Process., Vol. 10, No. 4, pp. 347-354.
  10. H. Ziegler, 1963, Progress in Solid Mechanics, John Wiley and Sons. New York, NY., Vol. 4, p. 93.