DOI QR코드

DOI QR Code

외란관측기를 이용한 모션 스테이지의 위치제어

Position Control of Motion Stage using Disturbance Observer

  • 발행 : 2013.06.30

초록

For commercialized servo drives of the motion stage to include embedded controller, external terminal is provided for tracking command and encoder output, but internal terminal is not for control input. Thus, it is difficult to combine out signal of embedded controller with that of external compensator such as disturbance observer. In this study, for precise tracking control of motion stage without hardware change of the servo drive, tacking control system is composed of an inner loop of servo drive and an outer loop of disturbance observer. Then, the control system is designed so that the output response of actual plant corresponds with nominal model's in transient state as well as in steady state. Finally, the experiment results show that the designed control system is effective to reconcile actual plant behavior with nominal model under nonlinear friction and parameter perturbation.

키워드

참고문헌

  1. C. Canudas, K. Astrom and K. Braun, 1987, "Adaptive Friction Compensation in DC-motor Drives", IEEE Trans. on Robotics and Automation, Vol. 3, pp. 681-685. https://doi.org/10.1109/JRA.1987.1087142
  2. J. H. Byun and M. S. Choi, 2012, "A Method of Synchronous Control System for Dual Parallel Motion Stages", IJPEM, Vol. 13, No. 6, pp. 883-889. https://doi.org/10.1007/s12541-012-0115-2
  3. P. E. Dupont and E. P. Dunlap, 1995, "Friction Modeling and PD Compensation at Very Low Velocities", Trans. of ASME, Vol. 117, pp. 8-14.
  4. O. H. Jang, B. G. Jang and G. J. Jang, 1997, "Neuro-Controller Design for the Line of Sight Stabilization System Containing Nonlinear Friction", Journal of CASE, Vol. 3, No. 2, pp. 139-148.
  5. A. Tesfaye, H. S. Lee and M. Tomizuka, 2000, "A Sensitivity Optimization Approach to Design of a Disturbance Observer in Digital Motion Control System", IEEE/ASME Trans. on Mechatronics, Vol. 5, No. 1, pp. 32-38. https://doi.org/10.1109/3516.828587
  6. M. Iwasaki, T. Shibata and N. Matui, 1999, "Disturbance-Observer-Based Nonlineal Friction Compensation in Table Drive Systems", IEEE/ASME on Mechatr., Vol. 4, No. 1, pp. 3-8.
  7. H. T. Choi, B. K. Kim and K. S. Eom, 2004, "Design of Generalized Model-base Disturbance Rejection Controller with Two Loops", JCASE, Vol. 10, No. 5, pp. 385-394. https://doi.org/10.5302/J.ICROS.2004.10.5.385
  8. H. R. Kim, Y. J. Choi, I. H. Suh and W. K. Chung, 2006, "Tracking Performance Improvement for Optical Disk Drive Using Error-based Modified Disturbance Observer", JCASE, Vol. 12, No.7, pp. 637-643. https://doi.org/10.5302/J.ICROS.2006.12.7.637
  9. T. Sugie and T. Yoshikawa., 1986, "General solution of robust tracking problem in Two-Degree-of-Freedom", IEEE Transaction on Automatic Control, Vol. AC-31, pp. 552-554.
  10. J. Doyle, C. Francis and A. R. Tannenbaum, 1992, "Feedback Control Theory", Maxwell Macmillan.
  11. H. S. Lee and M. Tomizuka, 1996, "Robust Motion Controller Design for High Accuracy Position Systems", IEEE Trans. Industrial Electronics, Vol. 43, pp 48-55. https://doi.org/10.1109/41.481407