한국표면공학회지 (Journal of Surface Science and Engineering)

  • 제46권3호
  • /
  • Pages.126-132
  • /
  • 2013
  • /
  • 1225-8024(pISSN)
  • /
  • 2288-8403(eISSN)
한국표면공학회 (The Korean Institute of Surface Engineering)
권호 표지
DOI QR코드

DOI QR Code

수소장입시킨 590 MPa DP강의 표면층 물성변화에 관한 수소의 영향

The Effect of Hydrogen on the Variation of Properties at the Surface Layers of 590 MPa DP Steels Charged with Hydrogen

  • 최종운 (서울과학기술대학교 신소재공학과) ;
  • 박재우 (서울과학기술대학교 에너지환경대학원 신에너지공학과) ;
  • 강계명 (서울과학기술대학교 신소재공학과)
  • Choi, Jong-Un (Department of Materials Science & Engineering, Seoul National University of Science and Technology) ;
  • Park, Jae-Woo (Department of New Energy Engineering, Graduate School of Energy & Environment, Seoul National University of Science & Technology) ;
  • Kang, Kae-Myung (Department of Materials Science & Engineering, Seoul National University of Science and Technology)
  • 투고 : 2013.05.15
  • 심사 : 2013.06.10
  • 발행 : 2013.06.30
PDF 다운로드
⟨ 이전 논문 다음 논문 ⟩

초록

It was investigated that the effects of hydrogen charging on the properties of 590 MPa Dual Phase(DP) steels at the surface layers. The hydrogen-charging time was changed from 5 to 50 hours and current densities from 100, 150, and 200 $mA/cm^2$, respectively. It was found that the hydrogen content in the specimen was increased with as the charging time and the current density. The microvickers hardness of the subsurface zone was increased from 215.3 HV to 239.5 HV due to the increase in current density and charging time. The comparison of the absorbed energies tested by a small-punch (SP) test showed that the absorbed energy of the specimen was greatly reduced from 436 to 283 $kgf-mm^2$ because of hydrogen embrittlement. It was confirmed that bulb aspects of fracture surface became more brittle with increasing hydrogen content.

키워드

참고문헌

  1. R. Kot, J. W. Morris, TMS/AIME, (1979) 362.
  2. R. G. Davies, C. L. Magee, J. Met., 31 (1979) 17.
  3. G. Katano, K. Ueyama, M. Mori, J. Mater. Sci., 36 (2001) 2277. https://doi.org/10.1023/A:1017568706014
  4. J. P. Hirth, Metall. Trans., 11A, (1980) 861.
  5. R. G. Davies, Metall. Trans., 12A, (1981) 1668.
  6. W. Y. Choo, J. Y. Lee, Metall. Trans., 13A, (1982) 135.
  7. A. R. Troiano, ASM Trans., 52 (1960), 54.
  8. J. U. Choi, J. W. Park, K. M. Kang, Kor. J. Mater. Res., 21 (2011) 581. https://doi.org/10.3740/MRSK.2011.21.11.581
  9. J. W. Park, K. M. Kang, Kor. J. Mater. Res., 22 (2012) 29. https://doi.org/10.3740/MRSK.2012.22.1.029
  10. K. M. Kang, J. W. Park, J. U. Choi, J. Kor. Inst. Surf. Eng., 26 (2013) 48.
  11. H. Matsui, H. Kimura, Mater. Sci. Eng. 40 (1979) 227. https://doi.org/10.1016/0025-5416(79)90193-9
  12. Standard Test Method for Ball Punch Deformation of Metallic Sheet Material, ASTM E643-84 (2000).
  13. M. Wang, E. Akiyama, K. Tsuzaki, Corros. Sci. 49 (2007) 4081. https://doi.org/10.1016/j.corsci.2007.03.038
  14. C. C. Lee, J. W. Park, K. M. Kang, Kor. Inst. Surf. Eng., 45 (2012) 128.
  15. T. Zhang, W. Y. Chu, K. W. Gao, L. J. Qiao, Mater. Sci. Eng., A347 (2003) 291.
  16. Y. Z. Liu, X. T. Zu, C. Li, S. Y. Qiu, W. J. Li, X. Q. Huang, Scripta Mater., 52 (2005) 821. https://doi.org/10.1016/j.scriptamat.2005.01.017

피인용 문헌

  1. Nanoindenter Test of 680MPa Dual Phase Steel Charged with Hydrogen vol.47, pp.1, 2014, https://doi.org/10.5695/JKISE.2014.47.1.033
  2. Small Punch Test of TRIP Steel Charged with Hydrogen under Different Electrolyte Condition vol.19, pp.1, 2015, https://doi.org/10.7842/kigas.2015.19.1.64
  3. Hydrogen Embrittlement of 680 MPa DP sheet steel with Electrochemical Hydrogen charging conditions of Two Electrolytes vol.47, pp.5, 2014, https://doi.org/10.5695/JKISE.2014.47.5.257
  4. Analysis of Correlation between the Hydrogen Embrittlement and the Small Punch Test for Hydrogen-charged Dual Phase Steels vol.18, pp.1, 2014, https://doi.org/10.7842/kigas.2014.18.1.61
  5. Evaluation on Hydrogen Embrittlement of 5 Types of High Strength Dual Phase Steels by Small Punch Test vol.18, pp.5, 2014, https://doi.org/10.7842/kigas.2014.18.5.40