DOI QR코드

DOI QR Code

유체의 점성이 원심펌프 성능에 미치는 영향

Effect of Fluid Viscosity on Centrifugal Pump Performance

  • 투고 : 2012.12.10
  • 심사 : 2013.04.10
  • 발행 : 2013.06.01

초록

원심펌프 작동유체의 점도변화에 따른 성능특성을 실험적인 방법으로 연구하였다. 비교적 비속도가 낮은 소형 원심펌프에 뉴턴유체인 설탕수용액과 글리세린수용액을 사용하여 작동유체의 점도를 변화시켜 가며 펌프성능시험을 수행한 후 전양정, 축동력 및 펌프의 효율을 청수의 경우와 비교 분석하여 얻은 결과는 다음과 같았다. (1) 전양정은 작동유체의 점도를 변화시킬 경우 청수에 비해 점도가 높아짐에 따라서 차단점에서의 양정은 극히 적은 변화를 보였으나, 유량이 증가함에 따라 양정의 감소하는 폭이 크게 나타났다. 따라서 유량-양정곡선(H-Q 곡선)의 기울기가 급해짐을 알 수 있었다. (2) 축동력은 작동유체의 점도가 청수에 비해 클수록 증가하였으며 차단점에서는 소요동력이 열로 소산되어 차이가 거의 없었으나, 유량이 증가할수록 축동력의 증가하는 폭이 커짐을 알 수 있었다.

The characteristics of centrifugal pump performance according to fluid viscosity change were studied experimentally. A small volute pump with low specific speed was tested by changing the viscosity of an aqueous solution of sugar and glycerin, which is considered a Newtonian fluid. After finishing the test, the total head, shaft horsepower, and pump efficiency were compared with those of a water pump. The results are summarized as follows: (1) when the fluid viscosity is increased, the shut-off head shows very little change but the total head decreases gradually as the flow increases, and this makes the H-Q curve leaning rapidly, and (2) when the fluid viscosity is increased, the shaft horsepower shows very little change at the shutoff condition; however, the shaft horsepower increases more rapidly with an increase in the flow and viscosity.

키워드

참고문헌

  1. Hydraulic Institute, 1969, Standard of H.I, Centrifugal Pump Section.
  2. KS B 6301, 2011, Testing Methods for Centrifugal Pumps, Mixed Flow Pumps and Axial Flow Pumps, Korean Standards Association.
  3. KS B 6302, 2011, Measurement Methods of Pump Discharge, Korean Standards Association.
  4. Stepanoff, A.J., 1948, Centrifugal and Axial Flow Pump.
  5. KS B 6306, 2010, Testing Methods for Centrifugal Type Oil Pumps, Korean Standards Association.
  6. Hodge, B.K., 1994, Analysis and Design of Energy System, 2nd ed., Prentice-Hall, Inc. New Jersey.
  7. I.S.O 1940, 1986, Balance Quality of Rotating Rigid Bodies, International Organization for Standardization TC 108.
  8. Frank M. White, 2008, Fluid Mechanics.
  9. WILO, 2012, Pump Technology Handbook.
  10. Hyosung Ebara, 2008, HEC Pump Hand Book.