Journal of Navigation and Port Research (한국항해항만학회지)

Korean Institute of Navigation and Port Research (한국항해항만학회)
권호 표지
DOI QR코드

DOI QR Code

Verification of Prediction Technique of Wave-making Resistance Performance for a Ship attached with a Vertical Blade

수직날개를 부착한 선박의 조파저항 성능 추정 기법의 검증

  • Choi, Hee-Jong (Department of Naval Ardchitecture & Ocean Engineering, Chonnam National University) ;
  • Park, Dong-Woo (Maritime Research Institute, Hyundai Heavy Institute)
  • 최희종 (전남대학교 조선해양공학과) ;
  • 박동우 (현대중공업 선박연구소)
  • Received : 2012.10.11
  • Accepted : 2013.01.24
  • Published : 2013.02.28
Download PDF
⟨ Previous Next ⟩

Abstract

In this paper the developed prediction technique of wave-making resistance performance for a ship attached with a vertical blade had been verified. Numerical analysis program as a prediction technique had been developed using the Rankine source panel method and the vortex lattice method(VLM). The nonlinearity of the free surface conditions was fully taken into account using the iterative method and the trim and the sinkage of the ship were also considered in the numerical analysis program. Panel cutting method was applied to get hull surface panels. Numerical computations were carried out for a 4000TEU container carrier and the vertical blade was attached 6 different locations astern. To investigate the validity of the numerical analysis program the commercial viscous flow field analysis program FLUENT was used to obtain the viscous flow field around the ship and the model test was performed. The model test results were compared with the numerical analysis results.

본 연구에서는 개발된 선미부에 수직날개를 부착한 선박의 조파저항성능을 예측할 수 있는 수치해석기법의 검증에 관한 것이다. 수치해석기법은 비점성 유동장 해석기법인 랜킨소오스 패널법과 와류격자법을 사용하여 개발하였으며, 자유수면 경계조건의 비선형성은 반복해법을 사용하여 만족시켰고, 선박의 트림과 침하량을 구하는 알고리즘을 포함하고 있다. 수치해석을 위한 선체표면의 패널을 생성하기 위하여 패널절단법을 사용하였다. 4000TEU 컨테이너 운반선을 대상 선박으로 하여 선미부 6개소의 서로 다른 위치에 수직날개를 부착하여 수치해석을 수행하였으며, 수치해석기법의 타당성을 검증하기 위하여 상용 점성 유동장 해석 프로그램인 FLUENT를 사용하여 선체 주위의 점성 유동장을 계산하였고, 모형시험을 수행하여 얻은 실험 결과를 수치해석 결과와 서로 비교하였다.

Keywords

References

  1. Broadley, I. and Garry, K.(1997), "Effectiveness of Vortex Generator Position and Orientation on Highly Swept Wings", 15th AIAA Applied Aerodynamic Conference, AIAA 1997-2319.
  2. Choi, H. J., Chun, H. H., Park, I. R. and Kim, J.(2011), "Panel cutting method: new approach to generate panels on a hull in Rankine source potential approximation", International Journal of Naval Architecture and Ocean Engineering, Vol. 3, pp. 225-232. https://doi.org/10.3744/JNAOE.2011.3.4.225
  3. Choi, H. J., Chun, H. H., Yoon, H. S., Lee, I. W., Park, D. W. and Kim. D. J.(2009), "Potential Flow Analysis for a Ship with a Flow Control Plate near the Stern", Journal of the Society of Naval Architecture, Vol. 46, No. 6, pp. 587-594. https://doi.org/10.3744/SNAK.2009.46.6.587
  4. Park, D. W., Choi, H. J., Yoon, H. S. and Chun, H. H.(2009), "A Numerical Study for Improvement of the Speedperformance of a Ship with Flow Control Flat Plate", Journal of the Society of Naval Architecture, Vol. 46, No. 3, pp. 268-278. https://doi.org/10.3744/SNAK.2009.46.3.268
  5. Seo, K. C., Atlar, M., Kim, H. J., Chun, H. H. and Kang, D. S.(2007), "Efficient Propulsion of a Container Ship Using the Inclined Keel Concept", Journal of the Society of Naval Architects of Korea, Vol. 44, No. 4, pp. 379-388. https://doi.org/10.3744/SNAK.2007.44.4.379
  6. Seo, K. C., Atlar, M., Kim, H. J. and Chun, H. H.(2009), "Minimization of Wave-Making Resistance for Inclined Keel Containership", Journal of the Society of Naval Architects of Korea, Vol. 46, No. 2, pp. 97-104. https://doi.org/10.3744/SNAK.2009.46.2.097
  7. Wendt, B. J. and Reichert, B. A.(1996), The Modelling of Symmetric Airfoil Vortex Generators, NASA Contractor Report 198501, AIAA-1996--0807.