• Journal of the Society of Naval Architects of Korea
• /
• v.42 no.4 s.142
• /
• pp.315-321
• /
• 2005

The effect of water depth on the wave making resistance performance is great where Froude number based on the water depth is close to one. The increase of wave making resistance due to the shallow water effect is evaluated by a numerical analysis in the present study. Three-dimensional Navier-Stokes and continuity equations are employed for the present study and the equations are discretized by finite difference method. The interface between water and air is determined by the level set method. In order to validate the numerical method, the change of resistance performance for Wigley hull according to the water depth is evaluated and the computed resistance coefficient is compared with measured one. The present numerical method is applied for the simulation of wave phenomena around a Ro-Pax hull form and the computed results are discussed in the resistance performance point of view.

• Journal of Navigation and Port Research
• /
• v.36 no.10
• /
• pp.787-793
• /
• 2012

A hull form design technique to enhance the wave-making resistance performance for a medium size high speed Ro-Pax ship was studied introducing an optimization method and an automatic hull form modification method. SQP(sequential quadratic programming) was applied as the optimization algorithm and the geometry of hull surface was represented and modified using the NURBS(Non-Uniform Rational B-Spline). The wave-making resistance performance as an objective function in the optimization procedure was evaluated using the Rankine source panel method in which nonlinearity of the free surface boundary conditions and the trim and sinkage of the ship was fully taken into account. Using the Ro-Pax ship as a base hull, the hull-form optimization method was applied to obtain the hull shape that produced the lower wave-making resistance. To verify the validity of the hull-form optimization method, the numerical results was compared with the model test results.

• Journal of the Society of Naval Architects of Korea
• /
• v.48 no.2
• /
• pp.99-106
• /
• 2011

The appearance of CSR changes the concept of the hull form design as well as structural design, since the application of CSR inevitably brings the lightweight increase of a ship. Keeping the original design constraints such as principal particulars, deadweight, and speed performance, designers have to increase the volume of the hull form. As a result, the entrance angle at bow end should become larger, which results in blunter waterline shape. For a slow and full ship having high $C_B$ more than 0.85, a new concept of bow shape has been required to alleviate the increase of wave-making resistance, since it is very difficult to improve waterline and frameline shape for such a full ship. In this paper a new bow shape of Capesize Bulk Carrier was developed to improve its wave-making characteristics without incompliance with the design constraints. For loading manual calculation, NAPA software was used. FLUENT6.3.26 and WAVIS1.4 were used to evaluate resistance performance of the subject hull forms. The newly designed hull form was tested at SSPA model basin for the final confirmation of resistance and propulsion performance of the ship. It was found that the new bow shape of a Capesize Bulk Carrier improved the resistance characteristics greatly compared to a conventional bulbous bow. The other benefits of new bow shape on the manufacturability were also investigated.

• Bulletin of the Society of Naval Architects of Korea
• /
• v.8 no.2
• /
• pp.45-52
• /
• 1971

The object of this study is to determine theoretical ship form which minimises wave making resistance under given conditions and developes theoretical ship form planing. By employing the streamline tracing method 1967's Korean Standard Ship Form of 10,000 G.T. linear has been reformed and tested at towing tank of Inha Institute of Technology. The design process and the reformed ship forms had been reported already in reference[4]. In this paper, resistance performance is experimentally observed with three models(original, theoretical, and reformed form) of 2m long in the towing tank, and total resistance of theoretical and reformed ship forms are decreased by 24.9% and 19.7% and wave making resistance by 66.4% and 47.7% compare to original ship form respectively.

• Journal of the Korean Society of Marine Environment & Safety
• /
• v.19 no.1
• /
• pp.78-84
• /
• 2013

The primary objective of the current work is to develop efficient numerical code to assess the resistance performance of the twin hull form. Resistance performance for the two different twin hull forms with asymmetric and symmetric mono hull using developed code are evaluated. Numerical calculations and model tests have been compared to validate a developed code used in the current work. Comparison were carried out through sinkages of the bow and stern, trim angle and wave-making resistance. Comparative analysis regarding hydrodynamic characteristic of different twin hull forms is worthy of application in the hull form development stage.

• Journal of Navigation and Port Research
• /
• v.37 no.1
• /
• pp.1-7
• /
• 2013

In this paper the developed prediction technique of wave-making resistance performance for a ship attached with a vertical blade had been verified. Numerical analysis program as a prediction technique had been developed using the Rankine source panel method and the vortex lattice method(VLM). The nonlinearity of the free surface conditions was fully taken into account using the iterative method and the trim and the sinkage of the ship were also considered in the numerical analysis program. Panel cutting method was applied to get hull surface panels. Numerical computations were carried out for a 4000TEU container carrier and the vertical blade was attached 6 different locations astern. To investigate the validity of the numerical analysis program the commercial viscous flow field analysis program FLUENT was used to obtain the viscous flow field around the ship and the model test was performed. The model test results were compared with the numerical analysis results.

• International Journal of Naval Architecture and Ocean Engineering
• /
• v.12 no.1
• /
• pp.856-867
• /
• 2020

This paper aims to provide the most useful method of determining an optimum LCB position and design direction of fore- and aft-body hull shape for a SLBV. It is known that the SLBV has a lower length-to-beam ratio, larger Cb and simpler stern shape designed for the installation of azimuth thrusters comparing to those of conventional LNG carriers. Due to these specific particulars of SLBV, the optimum LCB position was very different to that of conventional LNG carrier. And various approaches were applied to determine the optimum fore- and aft-body hull shape. The design direction for the optimum hull-form was evaluated as the minimization of the total resistance which includes the wave-making resistance and form-drag with numerical simulation.

• International Journal of Naval Architecture and Ocean Engineering
• /
• v.12 no.1
• /
• pp.38-47
• /
• 2020

The partial air cushion supported catamaran (PACSCAT) is a novel Surface Effect Ship (SES) and possesses distinctive resistance performance due to the presence of planing bottom. In this paper, the design of PACSCAT and air cushion system are described in detail. Model tests were carried out for Froude numbers ranging from 0.1 to 1.11, the focus is on the influence of air cushion system on resistance characteristics. Drag-reducing effect of air cushion system was proved by means of contrast tests in cuhionborne and non-cushionborne mode. Wave-making characteristics reflect that the PACSCAT would eventually enter planing regime, in which the air could just escape under the seals and the hull body could operate in a steady state. To acquire different air cushion pressure, air flow rate and leakage height were adjusted during tests. Experimental results show that the resistance performance in planing regime would decrease evidently as the increased air flow rate, however, the scheme with medium leakage height presents the best resistance performance in the hump region.

• Journal of Navigation and Port Research
• /
• v.34 no.10
• /
• pp.741-746
• /
• 2010

It is necessary to estimate more accurately the resistance of barge in still water and waves to compute the break load of towline and towing power for safety towing performance. The method proposed by government has calculated the total resistance of barge which is composed of frictional resistance, wave making resistance and air resistance considering the shape of hull and towing speed. However, the added resistance is equally applied with the significant wave height regardless of the type of vessels. In this study, we have carried out the numerical calculation to estimate the added resistance of wigley model in waves and compared with the experiment data to confirm the accuracy of the method. Then the computation was executed for the barge varying shape of the bow. As a result, added resistance of barge was differently occurred i.e. 0.3∼1.1 ton according to encounter angle, 0.4∼1.2 ton according to towing speed and 0.5∼1.1 ton according to shape of bow.

• Journal of Ocean Engineering and Technology
• /
• v.13 no.2 s.32
• /
• pp.168-175
• /
• 1999

In the present paper, a hull form for the turtle boat type incinerating vessel was developed based on the Finite source Distribution Method(FDM) and 1-$C_p$ method. In order to obtain proper hull form within the limited time and budget, a computer program OCL(Optimization of $C_p$ and LCB) was developed adn used. For the confirmation of the theoretical results by OCL, these theoretical results were compared with results of model test in the circulating water channel (CWC)in Chosun University.