참고문헌
- Kim, S. B., Huh, H., Bok, H. H., and Moon, M. B., "Forming limit diagram of auto-body steel sheets for high-speed sheet metal forming," J. of Mater. Process. Technol., Vol. 211, No. 5, pp. 851-862, 2010.
- Kuroda, M. and Tvergaard, V., "Forming limit diagrams for anisotropic metal sheet with different yield criteria," Int. J. of Solids and Struct., Vol. 37, No. 37, pp. 5037-5059, 2000. https://doi.org/10.1016/S0020-7683(99)00200-0
- Stoughton, T. B. and Yoon, J. W., "A new approach for failure criterion for sheet metals," Int. J. Plasticity, Vol. 27, No. 3, pp. 440-459, 2011. https://doi.org/10.1016/j.ijplas.2010.07.004
- Dejardin, S., Thibaud, S., and Gelin, J. C., "Finite element analysis and experimental investigation for improving precision in single point incremental sheet forming process," Int. J. Mater. Form., Vol. 1, Suppl. 1, pp. 121-124, 2008. https://doi.org/10.1007/s12289-008-0031-2
- Kim, T. J. and Yang, D. Y., "Inprovement of formability for the incremental sheet metal forming process," Int. J. Mech. Sci., Vol. 42, No. 7, pp. 1271-1286, 2000. https://doi.org/10.1016/S0020-7403(99)00047-8
- Yoon, J. W., Barlat, F., Gracio, J. J., and Rauch, E., "Anisotropic strain hardening behaviour in simple shear for cube textured aluminium alloy sheets," Int. J. Plasticity, Vol. 21, No. 12, pp. 2426-2447, 2005. https://doi.org/10.1016/j.ijplas.2005.03.014
- Chio, S.-H., Kim, D. H., Park, S. S., and You, B. S., "Simulation of stress concentration in Mg alloys using the crystal plasticity finite element method," Acta Mater., Vol. 58, No. 1, pp. 320-329, 2010. https://doi.org/10.1016/j.actamat.2009.09.010
- Dao, M. and Li, M., "A micromechanical study on strain-localization-induced fracture initiation in bending using crystal plasticity models," Philosophical Magazine A, Vol. 81, No. 8, pp. 1997-2020, 2001. https://doi.org/10.1080/01418610108216649
- Ko, J. B., Goh, C. H., and Lee, K. S., "The study of microstructure influence at fretting contacts using crystal plasticity simulation," J. of the KSPE, Vol. 22, No. 8, pp. 84-91, 2005.
- Ha, S. Y. and Kim, K. T., "Finite element analysis for rate-independent crystal plasticity model," Trans. of the KSME A, Vol. 33, No. 5, pp. 447-454, 2009.
- Kielsen, K. L. and Tvergaard, V., "Effect of a shear modified Gurson model on damage development in a FSW tensile specimen," Int. J. Solids and Struct., Vol. 46, No. 3-4, pp. 587-601, 2009. https://doi.org/10.1016/j.ijsolstr.2008.09.011
- Tvergaard, V. and Needleman, A., "Analysis of the cup-cone fracture in a round tensile bar," Acta Mater., Vol. 32, No. 1, pp. 157-169, 1984. https://doi.org/10.1016/0001-6160(84)90213-X
- Zhang, Z. L., Thaulow, C., and Odegard, J., "A complete Gurson model approach for ductile fracture," Eng. Fract. Mech., Vol. 67, No. 2, pp. 155-168, 2000. https://doi.org/10.1016/S0013-7944(00)00055-2
- Cockcroft, M. G. and Latham, D. J., "Ductility and the workability of metals," J. of the Institute of Metals, Vol. 96, pp. 33-39, 1968.
- Kim, J. B., Hong, S. H., and Yoon, J. W., "An analysis of necking behavior of Aluminium 6022-T4 based on crystal plasticity model," Proc. of KSME, pp. 81-82, 2012.
- Dao, M. and Asaro, R. J., "Localized deformation modes and non-schmid effects in crystalline solids. Part I. Crytical conditions of localization," Mech. Mater., Vol. 23, No. 2, pp. 71-102, 1996. https://doi.org/10.1016/0167-6636(96)00012-9
- ABAQUS Inc., "ABAQUS theory manual," 2006.
피인용 문헌
- Analysis of the Necking Behaviors with the Crystal Plasticity Model Using 3-Dimensional Shaped Grains vol.684, pp.1662-8985, 2013, https://doi.org/10.4028/www.scientific.net/AMR.684.357