Transactions of the Korean Society of Mechanical Engineers A (대한기계학회논문집A)

The Korean Society of Mechanical Engineers (대한기계학회)
권호 표지
DOI QR코드

DOI QR Code

Fast Simulation of Output Voltage for High-Shock Piezoresistive Microaccelerometer Using Mode Superposition Method and Least Square Method

모드중첩법 및 최소자승법을 통한 고충격 압저항 미소가속도계의 출력전압 해석

  • Han, Jeong-Sam (Dept. of Mechanical Design Engineering, Andong Nat'l Univ.) ;
  • Kwon, Ki-Beom (Dept. of Mechanical Design Engineering, Andong Nat'l Univ.)
  • 한정삼 (안동대학교 기계설계공학과) ;
  • 권기범 (안동대학교 기계설계공학과)
  • Received : 2012.01.27
  • Accepted : 2012.04.26
  • Published : 2012.07.01
Download PDF
⟨ Previous Next ⟩

Abstract

The transient analysis for the output voltage of a piezoresistive microaccelerometer takes a relatively high computation time because at least two iterations are required to calculate the piezoresistive-structural coupled response at each time step. In this study, the high computational cost for calculating the transient output voltage is considerably reduced by an approach integrating the mode superposition method and the least square method. In the approach, data on static displacement and output voltage calculated by piezoresistive-structural coupled simulation for three acceleration inputs are used to develop a quadratic regression model, relating the output voltage to the displacement at a certain observation point. The transient output voltage is then approximated by a regression model using the displacement response cheaply calculated by the mode superposition method. A high-impact microaccelerometer subject to several types of acceleration inputs such as 100,000 G shock, sine, step, and square pulses are adopted as a numerical example to represent the efficiency and accuracy of the suggested approach.

본 논문에서는 여러 가지 충격하에서 압저항 고충격 미소가속도계의 과도 출력전압의 계산시 발생하는 방대한 계산 시간 문제를 모드중첩법 및 최소자승법을 이용하여 압저항 미소가속도계의 실시간 출력전압 계산이 가능하도록 효율적인 출력전압 과도해석 방법을 제안한다. 우선 정적 압저항-구조 해석을 통하여 미소가속도계의 변위와 출력전압을 계산하고 출력전압을 특정 위치의 변위에 관한 2차 다항식으로 근사화하여 그 회귀계수를 최소자승법을 통하여 결정한다. 이후에 모드중첩법을 통하여 여러 방향의 고충격하에서 미소가속도계의 과도 변위응답을 계산하고, 이 변위응답을 변위로 표현되는 출력전압 근사식에 대입하여 과도 출력전압을 예측한다. 100,000 G 고충격파, 사인파, 계단파 및 사각파 등의 여러 가지 고충격 입력에 대한 압저항 미소가속도계의 수치예제를 통하여 제안한 방법의 정확성 및 효율성을 검증하였다.

Keywords

References

  1. Roylance L. M. and Angell, J. B., 1979, "A batch-Fabricated Silicon Accelerometer," IEEE Trans. Electron Devices, Vol. ED-26, No. 12. pp. 1911-1917.
  2. Rodulf F., 1983, "Micromechanical Capacitive Accelerometer with a Two-Point Inertial-Mass Suspension," Sensors and Actuators, Vol. 4, pp. 191-198. https://doi.org/10.1016/0250-6874(83)85024-0
  3. Kuehnel W. and Sherman S., 1994, "Surface Micromachined Silicon Accelerometer with On-Chip Detection Circuitry," Sensors and Actuators A, Vol. 45, pp. 7-16. https://doi.org/10.1016/0924-4247(94)00815-9
  4. Amarasinghe, R., Dao, D. V., Toriyama, T. and Sugiyama, S., 2007, "Development of Miniaturized 6-Axis Accelerometer Utilizing Piezoresistive Sensing Elements," Sensors and Actuators A, Vol. 134, pp. 310-320. https://doi.org/10.1016/j.sna.2006.05.044
  5. Van Kampen, R. P. and Wolffenbuttel, R. F., 1998, "Modeling the Mechanical Behavior of Bulk-Micromachined Silicon Accelerometers," Sensors and Actuators A, Vol. 64, pp. 137-150. https://doi.org/10.1016/S0924-4247(98)80007-1
  6. Wang, Q. M., Yang, Z., Li, F. and Smolinski, P., 2004, "Analysis of Thin Film Piezoelectric Microaccelerometer Using Analytical and Finite Element Modeling," Sensors and Actuators A, Vol. 113, pp. 1-11. https://doi.org/10.1016/j.sna.2004.02.041
  7. Fan, F., Che, L., Xiong, B. and Wang, Y., 2007, "A Silicon Micromachined High-Shock Accelerometer with a Bonded Hinge Structure," J. Micromech. Microeng., Vol. 17, pp. 1206-1210. https://doi.org/10.1088/0960-1317/17/6/015
  8. Y. Ning, Y. Loke, and G. McKinnon, 1995, "Fabrication and Characterization of High G-Force, Silicon Piezoresistive Accelerometers," Sensors and Actuators A, Vol. 48, pp. 55-61. https://doi.org/10.1016/0924-4247(95)00981-7
  9. Wang, Z., Zong, D., Lu, D., Xiong, B., Li, X. and Wang, Y., 2003, "A Silicon Micromachined Shock Accelerometer with Twin-Mass-Plate Structure," Sensors and Actuators A, Vol. 107, pp. 50-56. https://doi.org/10.1016/S0924-4247(03)00270-X
  10. Han, J. S., Kwon, S. J., Ko, J. S., Han, K. H., Park, H. H. and Lee, J. W., 2011, "Piezoresistive-Structural Coupled-Field Analysis and Optimal Design for a High Impact Microaccelerometer," Journal of the KIMST, Vol. 14, pp. 132-138.
  11. Kim, D. H., Sung, Y. K. and Jang, W. S., 2011, "Learning Input Shaping Control with Parameter Estimation for Nonlinear Actuators," Transactions of the KSME A, Vol. 35, No. 11, pp. 1423-1428.
  12. Lee, H. C. and Jee, S. C., 2009, "Integrated Auto-Tuning of a Multi-Axis Cross-Coupling Control System," Journal of the Korean Society for Precision Engineering, Vol. 26, No. 12, pp. 55-61.
  13. Eom, H. S., Kim, J. Y, Baek, J. Y. and Lee, M. C., 2010, "Reduction of Relative Position error for DGPS Based Localization of AUV Using LSM and Kalman Filter," Journal of the Korean Society for Precision Engineering, Vol. 27, No. 10, pp. 52-60.
  14. Kim, W., Lee, C. M., Lee, M. J. and Park, S. J., 2010, "A Study on the Development of Measuring System for Extra Long Roller Using Noncontact Sensor," Journal of the Korean Society for Precision Engineering, Vol. 27, No. 4, pp. 33-39.
  15. Shim, J. J., Han, G. J., Han, D. S., Lee, S. W. and Kim, T. H., 2004, "The Study on Piezoresistance Change Ratio of Cantilever type Acceleration Sensor," Journal of the Korean Society for Precision Engineering, Vol. 2004, No. 10, pp. 294-297.
  16. ANSYS, 2007, ANSYS Theory Reference 11.0, SAS IP, Inc.
  17. Noh, Y. S., Chung, J. T. and Bae, D. S., 1997, "Stability and Accuracy for the Trapezoidal Rule of the Newmark Time Integration Method with Variable Time Step Sizes," Transactions of the KSME A, Vol. 21, pp. 1712-1717.
  18. Park, J. S., Yoon, J. H. and Im, J. B., 2004, "Optimal Design of a Satellite Structure by Response Surface Method," Journal of Aeronautical and Space Science, Vol. 32, pp. 22-28.