Transactions of the Korean Society of Mechanical Engineers A (대한기계학회논문집A)

The Korean Society of Mechanical Engineers (대한기계학회)
권호 표지
DOI QR코드

DOI QR Code

Study on Dimensional Change in Wire Product During Wire-Drawing Process

선재 인발공정에서 인발제품의 선경변화에 대한 연구

  • Received : 2011.12.01
  • Accepted : 2012.04.19
  • Published : 2012.07.01
Download PDF
⟨ Previous Next ⟩

Abstract

During the cold wire-drawing process, the diameter of a wire is reduced and the length of the wire is increased as the wire passes through the die. The pressure and sliding motion at the interface between the wire and die cause elastic recovery of the workpiece and friction and wear on the die. In addition, wire deformation and frictional heating raise the temperature of the wire and die, resulting in difficulty in manufacturing the drawn products according to a designated inner diameter of the die, deviating from the designated dimension or the inner diameter of the die. In this study, considering the die temperature distribution, the effects of dimensional changes of the drawn products were analyzed quantitatively; these changes are caused by the elastic deformation of the die, the elastic recovery of the workpiece, and the thermal deformation of both the die and the workpiece. It was confirmed that the elastic recovery of the workpiece influenced these changes the most. The initial dies considering these factors could avoid deviation from the designated dimension, and the desired drawn products were obtained by using the designed initial drawing dies.

상온의 인발공정에서 소재는 인발다이를 통과하면서 직경이 줄어들고 길이가 늘어난다. 인발다이와 소재가 접촉한 면에서의 압력과 미끄럼 운동에 의해 소재에는 탄성회복, 인발 다이에는 마찰과 마모가 생긴다. 또한, 소재의 변형 및 마찰열로 인해 소재와 다이의 온도가 상승하며 이로 인해 지정된 다이 내경으로 제품이 가공되기 어려우며 소재의 선경은 지정된 직경 또는 다이 내경과 다르게 된다. 본 논문에서는 다이의 온도분포를 고려하여 소재의 탄성회복, 다이의 탄성변형, 그리고 다이와 소재의 열변형이 인발제품의 선경변화에 미치는 영향을 정량적으로 분석하였다. 네 가지 요인 중에서 소재의 탄성회복의 영향이 선경변화량의 대부분을 차지함을 확인하였다. 선경변화에 영향을 주는 인자들을 고려하여 지정된 치수와 차이를 주지 않는 초기 다이를 설계하였고, 설계된 초기 다이를 이용하여 지정된 치수의 인발제품을 얻을 수 있었다.

Keywords

References

  1. Kampus, Z., 1999, "Analysis of Factors Influencing Accuracy in the Drawing of Round Rods," Journal of Materials Processing Technology, Vol. 87, pp. 90-96. https://doi.org/10.1016/S0924-0136(98)00336-7
  2. Akiyama, M., Taniyama, A., Neishi, Y. and Hamada, T., 2004, "Dimensional Change in High Carbon Steel Wire Owing to Heavy Reduction by Tandem Cold Drawing," Material Science and Technology, Vol. 20, pp. 903-908 https://doi.org/10.1179/026708304225019632
  3. Lee, Y. S., Lee, J. H., Kwon, Y. N. and Ishikawa, T., 2004, "Analysis of the Elastic Characteristics at Die and Workpiece to Improve the Dimensional Accuracy for Cold Forged Part," Journal of Materials Processing Technology, Vol. 153-154, pp. 1081-1088. https://doi.org/10.1016/j.jmatprotec.2004.04.291
  4. Ishikawa, T., Yukawa, N., Yoshida, Y., Kim, H. and Tozawa, Y., 2000, "Prediction of Dimensional Difference of Product from Tool in Cold Backward Etrusion," CRIP Annals-Manufacturing Technology, Vol. 49, pp. 169-172. https://doi.org/10.1016/S0007-8506(07)62921-7
  5. Luksza, J., Majta, J., Burdek, M. and Ruminski, M., 1998, "Modelling and Measurements of Mechanical Behavior in Multi-Pass Drawing Process," Journal of Materials Processing Technology, Vol. 80-81, pp. 398-405. https://doi.org/10.1016/S0924-0136(98)00119-8
  6. Camacho, A. M., Domingo, R., Rubio, E. and Gonza Vlez, C., 2005, "Analysis of the Influence of Back-Full in Drawing Process by the Finite Element Method," Journal of Materials Processing Technology, Vol. 164-165, pp. 1167-1174. https://doi.org/10.1016/j.jmatprotec.2005.02.130
  7. Dixit, U. S. and Dixit, P. M., 1995, "An Analysis of the Steady-State Wire Drawing of Strain-Hardening Materials," Journal of Materials Processing Technology, Vol. 47, pp. 201-229. https://doi.org/10.1016/0924-0136(95)85000-7
  8. Castro, A. L. R., Campos, H. B. and Cetlin, P. R., 1996, "Influence of Die Semi-Angle on Mechanical Properties of Single and Multiple Pass Drawn Copper," Journal of Materials Processing Technology, Vol. 60, pp. 179-182. https://doi.org/10.1016/0924-0136(96)02325-4
  9. Norasethasopon, S. and Yoshida, K., 2006, "Influences of Inclusion Shape and Size in Drawing of Copper Shaped-Wire," Journal of Materials Processing Technology, Vol. 172, pp. 400-406. https://doi.org/10.1016/j.jmatprotec.2005.09.020
  10. Chen, D. C. and Huang, J. Y., 2007, "Design of Brass Alloy Drawing Process Using Taguchi Method," Materials Science and Engineering: A, Vol. 464, pp. 135-140. https://doi.org/10.1016/j.msea.2007.01.139
  11. Vega, G., Haddi, A. and Imad, A., 2007, "Modelisation Numerique de Mise en Forme par Trefilage," 18e ( Congres Francais de Mecanique, Grenoble, pp. 27-31.
  12. Vega, G., Haddi, A. and Imad, A., 2009, "Temperature Effects on Wire-Drawing Process: Experimental Investigation," International Journal of Material Forming, Vol. 2, Suppl 1: pp. 229-232. https://doi.org/10.1007/s12289-009-0468-y
  13. Rigaut, J. M., Oudin, J., Bricout, J. P., Cabezon, J. and Ravalard, Y., 1998, "A New Friction Test Procedure for the Improvement of Drawing and Similar Processes," Journal of Materials Processing Technology, Vol. 21, pp. 3-28.
  14. Obi, A. I. and Oyinlola, A. K., 1996, "Frictional Characteristics of Fatty-Based Oils in Wire Drawing," Wear, Vol. 194, pp. 30-37. https://doi.org/10.1016/0043-1648(95)06664-0
  15. Evans, W. and Avitzur, B., 1968, "Measurement of Friction in Drawing, Extrusion and Rolling," Journal of Lubrication Technology, pp.72-89.
  16. Kim, B. M., Kim, T. H. and Choi. J. C., 1997, "Prediction of Die Wear in the Wire-Drawing Process," Journal of Materials Processing Technology, Vol. 65, pp. 11-17. https://doi.org/10.1016/S0924-0136(96)02235-2
  17. Gillstrom, P. and Jarl, M., 2007, "Wear of Die After Drawing of Pickled or Reverse Bent Wire Rod," Wear, Vol. 262, pp. 858-867. https://doi.org/10.1016/j.wear.2006.08.016
  18. Hollinger, S., Depraetere, E. and Giroux, O., 2003, "Wear Mechanism of Tungsten Carbide Dies During Wet Drawing of Steel Tyre Cords," Wear, Vol. 255, pp. 1291-1299. https://doi.org/10.1016/S0043-1648(03)00168-6
  19. Moon, C. and Kim, N., "Analysis of the Wire Drawing Process with Friction and Thermal Conditions Obtained by Inverse Engineering," Journal of Mechanical Science and Technology, (submitted).
  20. Kang, G. J., Kim, J. and Kang, B. S., 2008, "Numerical and Experimental Evaluation for Elastic Deformation of a Cold Forging Tool and Workpiece for a Sleeve Cam of an Automobile Start Motor," Journal of Engineering Manufacture, Vol. 222, pp. 217-224. https://doi.org/10.1243/09544054JEM929

Cited by

  1. Dimensional Change in Drawn Wire Product in the Two Cross-Roll Straightening Process vol.37, pp.3, 2013, https://doi.org/10.3795/KSME-A.2013.37.3.295