DOI QR코드

DOI QR Code

Effect of volume fraction on stability analysis of glass fibre reinforced composite plate

  • Mini, K.M. (Faculty of Engineering (Civil), Amrita School of Engineering, Amrita Vishwa Vidyapeetham) ;
  • Lakshmanan, Mahadevan (Faculty of Engineering (Mechanical), Amrita School of Engineering, Amrita Vishwa Vidyapeetham) ;
  • Mathew, Lubin (Department of Mechanical Engineering, Amrita School of Engineering, Amrita Vishwa Vidyapeetham) ;
  • Kaimal, Girish (Department of Mechanical Engineering, Amrita School of Engineering, Amrita Vishwa Vidyapeetham)
  • 투고 : 2010.12.06
  • 심사 : 2011.10.27
  • 발행 : 2012.02.25

초록

This paper deals with an experimental investigation to study the effect of fibre content on the stability of composite plates with various aspect ratios. Epoxy based glass fibre reinforced composite plates with aspect ratio varying from 0.4 to 1 and with volume fractions of 0.36, 0.4, 0.46, 0.49 and 0.55 are used for the investigation. From the study it is observed that for plate with aspect ratio of 0.5 and 0.4 there is no buckling and the plate got crushed at the middle. As the volume fraction increases the buckling load also increases to a limit and then began to reduce with further increase in fibre content. The optimum range of fibre content for maximum stability is found between 0.49 and 0.55. Polynomial expressions are developed for the study of buckling behaviour of composite plates with different volume fractions in terms of load and aspect ratio.

키워드

참고문헌

  1. Ai Kah Soh, Li Chun Bian and Chakrabarty, J. (2000), "Elastic/plastic buckling of a composite flat plate subjected to uniform edge compression", Thin-Wall. Struct., 38(3), 247-265. https://doi.org/10.1016/S0263-8231(00)00038-0
  2. Akhbari, OM. Mahmood, M. Shokrieh. and Nosraty, H. (2008), "A study on buckling behavior of composite sheets reinforced by hybrid woven fabrics", Transactions of the CSME / de la SCGM, 32(1), 81-89.
  3. ASTM D2584. (2002), "Standard test method for ignition loss of cured reinforced resins", Annual Book of ASTM Standards, West Conshohocken, American Soc. Test. Mater., 8(1).
  4. ASTM D3039/D3039M. (2000), "Standard test method for tensile properties of polymer matrix composite materials", Annual Book of ASTM Standards, West Conshohocken, American Soc. Test. Mater., 15(3).
  5. Aymerich, F. and Serra, M. (2008), "Optimization of laminate stacking sequence for maximum buckling load using the ant colony optimization (ACO) metaheuristic", Compos: Part A., 39(2), 262-272. https://doi.org/10.1016/j.compositesa.2007.10.011
  6. Balamurugan,V, Ganapathi, M. and Patel, B.P.(1998), "Postbuckling behaviour of anisotropic laminated compositeplates due to shear loading", Defence Sci. J., 48(4), 433-440 https://doi.org/10.14429/dsj.48.3970
  7. Buket Okutan Baba and Aysun Baltaci. (2007), "Buckling characteristics of symmetrically and symmetrically laminated composite plates with central cut-outs", Compos. Mater., 14(4), 265-276 https://doi.org/10.1007/s10443-007-9045-z
  8. Chaitalli Ray. (2004), "An investigation on the effect of fiber weight fraction on buckling of laminated composite plates", J. Reinf. Plast. Compos., 23(9), 951-957. https://doi.org/10.1177/0731684404033957
  9. Fatai Olufemi aramdie, Isiaka Oluwole Oladele, and Davies Oladayo.(2008), "Evaluation of the effect of fiber volume fraction on the mechanical properties of polymer matrix composite", FOLORUNSO Metallurgical and Materials Engineering Dept., Federal University of Technology, Akure, Ondo State, Nigeria.
  10. Featherston, C.A. and A. Watson, A. (2005), "Buckling of optimised composite plates under shear and in-plane bending", Compos. Sci. Technol., 65(6), 839-853. https://doi.org/10.1016/j.compscitech.2004.07.007
  11. Iyengar N G R. (2006), "Structural stability of columns and plates", Affiliated East West Press Ltd.
  12. Kormaníková, E. and Mamuzic, I. (2008), "Buckling analysis of a laminate plate", METABK, 47(2), 129-132.
  13. Kyung-SuNa and Ji-Hwan Kim. (2006), "Three dimensional thermo mechanical buckling analysis for functionally graded composite plates", Compos. Struct., 73(4), 413-422. https://doi.org/10.1016/j.compstruct.2005.02.012
  14. Mallick,P.K.(2007), "Fiber-Reinforced Composites Materials, Manufacturing and Design, CRC Press, Taylor and Francis Group.
  15. Michael .P Nemeth. (1990), "Buckling and post buckling of compression loaded isotropic plates with cut outs", AIAA J., 29(2), 313-314.
  16. Mohd Aidy Faizal, Yeo Kiam Beng and Mohd Noh Dalimin. (2006), "Tensile property of hand layup plain-woven E-glass/ polyester composite: curing pressure and ply arrangement effect", Borneo Sci., 19, 27-34.
  17. Pein, C.W. and Zahari, R. (2007), "Experimental investigation of the damage behaviour of woven fabric glass/epoxy laminated plates with circular cut-outs subjected to compressive force", Inter. J. Eng. Technol., 4(2), 260-265.
  18. Roberts, J.C. Bao, G. and White, G.J. (1999), "Experimental, numerical and analytical results for bending and buckling of rectangular orthotropic plates", Compos. Struct., 43(4), 289-299.
  19. Shrivastava, A.K and Singh, R.K. (1999), "Effect of aspect ratio on buckling of composites", Compos. Sci. Technol.,59(3), 439-445. https://doi.org/10.1016/S0266-3538(98)00087-6

피인용 문헌

  1. Brass fillers in friction composite materials: Tribological and brake squeal characterization for suitable effect evaluation vol.19, pp.4, 2015, https://doi.org/10.12989/scs.2015.19.4.939
  2. Strengthening Steel Members with Holes Under Tension Using Unidirectional GFRP Sheets vol.18, pp.2, 2018, https://doi.org/10.1007/s13296-018-0011-4