DOI QR코드

DOI QR Code

A Study on the Optimal Shape Design of Front Axle of Wheel Loader using the Design of Experiments

실험계획법을 이용한 휠 로더 전 차축의 최적형상에 관한 연구

  • Yoo, Dae-Won (Machine System Design, Graduate School of Knowledge based Technology and Energy, Korea Polytechnic Univ.) ;
  • Lee, Jai-Hak (Department of Mechanical Design Engineering, Korea Polytechnic Univ.)
  • 유대원 (한국산업기술대학교 지식기반기술.에너지대학원 기계시스템설계학과) ;
  • 이재학 (한국산업기술대학교 기계설계공학과)
  • Received : 2011.08.05
  • Accepted : 2011.11.01
  • Published : 2012.02.01

Abstract

Wheel loader is one of the construction machinery capable of variety of tasks and the demand on functional diversity and structural reliability is growing. As a study on the optimal shape design of front axle for wheel loader through the design of experiments, this paper assessed the design parameters affecting the maximum stress. As a result, a value of 126.77 MPa of minimum stress was obtained, and optimal factors showed the values of w = 100.0 mm, ${\theta}=40^{\circ}$ and R = 118 mm. It showed an accuracy of 98.7% compared with the structural analysis.

Keywords

References

  1. Park, Y. J., Oh, J. Y., Yun, U. K. and Lee, G. H., "Design Parameter Analysis of the Proportional Control Valve for Wheel-Loader Automatic Transmission," J. of KSPE, Vol. 27, No. 5, pp. 27-35, 2010.
  2. Pak, J. Y., Yoo, W. S., Kim, H. W., Hong, J. M. and Ko, K. G., "Three Dimensional Modeling and Simulation of a Wheel Loader," Proc. of the KSME Autumn Conference, pp. 870-874, 2004.
  3. Cho, H. D., Yoon, M. C. and Kim, Y. J., "Development of Loader Equipped with 4WD and 4WS(II)," J. of the Korea Society of Machine Tool Engineers, Vol. 8, No. 1, pp. 150-157, 1999.
  4. Jo, S. G., "Development of Loader Applied with 4 Wheel Driving and 4 Wheel Steering System," M.S. Thesis, Department of Mechanical Engineering, Graduate School, Kyungil University, pp. 1-5, 2002.
  5. Choung, J. M., Kim, G. S., Jang, W. S., Choe, I. H. and Heo, M. S., "Study on the Static/Dynamic Measurements and Structural Analysis Procedure of Wheel Loader," Proc. of the KSME Autumn Conference, pp. 1303-1309, 2003.
  6. Lee, S. S. and Kim, S. H., "Design and analysis of four wheel $90^{\circ}$ steering Loader," J. of Agricultural Science, Vol. 17, pp. 31-45, 2006.
  7. Yoo, S. W., "Optimal design of Wheel loader lift arm shape," M.S. Thesis, Department of Mechanical Engineering, Graduate School, Inha University, pp. 1-27, 2009.
  8. Kwon, K. B. and Shin, D. Y., "Optimal Design of a Mini-Loader Based on the Design of Experiments," Trans. of KSME A, Vol. 35, No. 6, pp. 693-699, 2011.
  9. Shin, J. H. and Lee, C. M., "A Study on Spindle Shape Design using Design Experiments," J. of KSPE, Vol. 26, No. 4, pp. 102-127, 2009.
  10. Kwon, K. H. and Chung, W. J., "Stress Analysis of a Tool Holder Spindle suing DOE with iSIGHT${\wedge}$(R)," Proc. of the Korean Society of Manufacturing Technology Engineers Spring Conference, pp. 348-353, 2009.
  11. Kim, H. J., Kim, H. S., Kim, J. P., Pack, J. H. and Yun, M. J., "Shape Optimization for Performance Improvement of Ship's U-type Bellows," J. of Ocean Engineering and Technology, Vol. 20, No. 6, pp. 123-129, 2006.
  12. Kim, J. M., Chung, W. J., Park, K. B., Kang, J. M., Jung, A. K., Joo, C. H. and Lee, S. K., "Optimal Design of Excavator Arm Part Using Design of Experiments," Proc. of KSPE Autumn Conference, pp. 361-362, 2007.
  13. Lee, C. W., Kim, M. S. and Yim, H. J., "Shape Optimization for Maximizing Fatigue Life of Suspension Component Using the Experimental Design," Proc. of KSPE Autumn Conference, pp. 726-731, 2002.
  14. SBP&T, "23-26ton class W/LOADER AXLE Endurance Test Mode," ES-01, pp. 4-6, 2006.
  15. Bak, S. H. and Kim, J. U., "Modern Design of Experiments Using the MINITAB," Minyoungsa, pp. 309-317, 2010.
  16. Yoo, M. H., "A Study on Design Optimization and Stress Relaxation Phenomenon on Lip Seal," Ph.D. Thesis, Graduate School of Knowledge-based Technology and Energy, Korea Polytechnic University, pp. 54-73, 2009.
  17. ELETEC, "Design of Experiments," pp. 225-309, 2010.
  18. ELETEC, "MINITAB 15${\circledR}$ for DOE," pp. 225-307, 2008.