한국철도학회논문집 (Journal of the Korean Society for Railway)

  • 제13권4호
  • /
  • Pages.363-370
  • /
  • 2010
  • /
  • 1738-6225(pISSN)
  • /
  • 2288-2235(eISSN)
한국철도학회 (The Korean Society for Railway)
권호 표지

철도차량 추진제어장치 성능시험을 위한 관성부하 시험설비의 구조안전성 및 동특성 평가 연구

A Study on Structural Integrity and Dynamic Characteristic of Inertial Load Test Equipment for Performance Test of Railway Vehicle Propulsion Control System

  • 장형진 (한밭대학교 기계설계공학과 경량구조 및 CAE 실험실) ;
  • 신광복 (한밭대학교 기계공학부) ;
  • 이상훈 (한밭대학교 기계설계공학과 경량구조 및 CAE 실험실) ;
  • 이대봉 (우진산전(주) 기술연구소)
  • 투고 : 2010.04.26
  • 심사 : 2010.06.18
  • 발행 : 2010.08.26
PDF 다운로드
⟨ 이전 논문 다음 논문 ⟩

초록

본 논문은 철도차량용 추진제어장치의 성능평가를 위한 관성부하 시험설비의 구조안전성 및 동특성 평가를 연구하였다. 추진제어장치는 철도차량의 핵심 부품으로서 차량에 적용하기 전에 안정성 및 신뢰성 검증이 충분히 이루어 져야 한다. 따라서 추진제어장치의 성능시험을 위한 관성부하 시험설비를 이론식을 바탕으로 하여 설계하였다. 설계된 관성부하 시험설비에 대해 Ansys v11.0을 이용하여 구조해석을 수행하였으며, ADAMS를 통해 동특성을 평가하였다. 관성부하 시험설비의 구조안전성은 조합하중하의 베어링에서 안전계수가 10.2로 만족하였다. 또한, 동적 시뮬레이션에 따른 플라이휠은 0.83mm이내의 최대진폭변위로 구조적 안정성이 확보되었다.

This paper describes the evaluation of structural integrity and dynamic characteristic of inertial load test equipments for performance test of railway vehicle propulsion control system. The propulsion control system of railway vehicle has to be confirmed of safety and reliability prior to its application. Therefore, inertial load test equipments were designed through theoretical equation for performance test of propulsion control system. The structural analysis of inertial load test equipments was conducted using Ansys v11.0 and the dynamic characteristic was evaluated using Adams. The results showed that the structural integrity of inertial load test equipment was satisfied with a safety factor of 10.2 on the bearing part under combined load. Also, the structural stability of flywheel according to dynamic simulation was secured by the maximum oscillation displacement within 0.83mm.

키워드

참고문헌

  1. Y.S. Lee, D.S. Moon (2007) A Study on the Development of High Speed Rail(HSR) and its Influence, Journal of the Korean Society for Railway, 10(1), pp. 23-37.
  2. S.J. Cho, M.K. Jeong, D.S. Kim (2009) The Technic of Propulsion Control System using High Speed Rail, The Korean Institute of Power Electronics, 14(5), pp. 25-30.
  3. M.K. Jeong, S.J. Cho, K.J. Lee, K.T. Park, D.S. Kim (2009) A Study on Inertial Load Test of Propulsion Control System using High Speed Rail, Summer Conference of the Korean Institute of Power Electronics, pp. 369-371.
  4. D.W. Jang, H.J. Park, M.S. Han (2006) Test Equipment Traction Motor for Electric Train, Summer Conference of the Korean Institute of Electrical Engineers, pp. 1103-1104.
  5. B.H. Bae, S.K. Sul (1999) Development of Electric Inertia Load for Traction System combined Testing, Summer Conferenc of the Korean Institute of Electrical Engineers, pp. 433- 435.
  6. J. holtz, W. lotzat, A.M. Hambadkone (1993) On continuous control of PWM inverter in the overmodulation range including the six-step mode, Trans. IEEE, on PE, 8(4), pp. 546-553.
  7. K.J. Lee, M.K. Jeong, Y.C. Ko, S.Y. Jang, L.S. Bang (1998) A Inertia Load Test using a Low Frequency Synchronous PWM Technique of High Efficiency for Electric Car, Spring Conference of the Korean Society for Railway, pp. 233-240.
  8. K.D. Kim, Y.J. Han, Y.S. Byun, H.J. Park, W.D. Lee (1999) A Inertia Load Test of IGBT Inverter for Urban Rail Traction, Conference of the Korean Institute of Power Electronics, pp. 118-121.
  9. W.S. Ko, D.W. Ryu, S.D. Oh, T.H. Sung, S.C. Han, Y.H. Han (2004) Structural Analsysis Considering Electromagnetic Force on Motor/Generator for Flywheel Energy Storage System, Spring Conference of the Korean Sosiety for Mechanical Engineers, pp. 485-490.
  10. J. Arellano-Padilla, G.M. Asher, M. Sumner (2006) Control of an AC Dynamometer for Dynamic Emulation of Mechanical Loads With Stiff and Flexible Shafts, IEEE Transactions on Industrial Electronics, 53, pp. 1250-1260.
  11. G.D. Kim, H.J. Park, Y.J. Han, K.H. Han, J.M. Cho (2002) A Miniature Inertia Simulator using Vector Controlled Induction Motor, The Korean Institute of Power Electronics, 7(1), pp. 74- 80.
  12. R.E. Kim, Y.H. Park, J.C. Kim, D.K. Kim, C.H. Kim (2009) Development of Traction Motor for Next Generation High Speed Train with Distributed Tractions, Autumn Conference of Korean Society for Railway, pp. 1607-1612.
  13. KSD 4122 (1993) Carbon Steel Forgings for Pressure Vessels, Korean Agency for Technology and Standards.
  14. Metals Handbook, Vol.2 (1990) Properties and Selection : nonferrous Alloys and Special-Purpose Materials, ASM International 10th Ed.
  15. K.H. Kim, Y.M. Yoo, J.S. Im, J.S. Hyun (2000) Evaluation of Boundary Conditions for Structural Analysis of Wheel Bearing Units, The Korean Society of Automotive Engineers, 8(6), pp.230-237.