DOI QR코드

DOI QR Code

Development of Wide Connection Method for Vertical Joints of Precast Concrete Walls

프리캐스트 콘크리트 벽체 수직접합부의 광폭형 연결방식 개발

  • Choi, Eun-Gyu (Dept. of Architecture Engineering, Ewha Womans University) ;
  • Shin, Yeong-Soo (Dept. of Architecture Engineering, Ewha Womans University)
  • Published : 2009.10.31

Abstract

This research analyzed the structural efficiency and application by improving the 100 mm width vertical joint to 150 mm and developing three connection methods to reduce the difficulty in assembling and handling PC walls. Moreover, nonlinear finite analysis was used for analyzing. From the analysis results, when double width connection was applied, the PC wall showed larger load capacity and ductility due to the steel bar sharing loads efficiently. Moreover, as the dimension of loops and the number of bars increased, the maximum load capacity increased as well. Also, among the double width connections, the largest capacity showed in the order of welding, ring and C type loop. However, in case of welding type loop connection, the ring type loop is more stable due to changes in different site conditions. Therefore, thorough quality control of welding is necessary.

이 연구에서는 프리캐스트 콘크리트 구조시스템에서 기존에 사용되고 있는 벽체의 수직접합부의 시공 및 문제점을 최소화하기 위해 접합부의 폭을 100 mm에서 150 mm로 증가시키고 연결방식을 3가지로 하여 구조적 성능 및 적용성에 대해 분석하였다. 또한, 해석적으로 구조적 성능을 파악하기 위해 비선형 유한 요소 해석법으로 분석하였다. 분석 결과, 광폭형 연결부를 가진 접합부를 적용하였을 때, PC벽체에 가해지는 하중을 더 효율적으로 철근이 분담하여 내력이 증가하고 연성적인 거동을 하는 것으로 나타났다. 또한, 접합부 루프근의 단면적이 커질수록 그리고 철근 개수가 증가할수록 최대내력이 증가하며 광폭형 접합부 형식 중에 용접형-링형-C형의 순서로 내력이 큰 것으로 나타났다. 용접형의 경우 현장조건에 따른 변화가 발생할 수 있으므로 광폭형 연결 부위를 링형 접합부로 하는 것이 안정적인 거동을 하며 현장 용접의 철저한 품질관리가 필요하다.

Keywords

References

  1. Kianoush, M. R. and Scanlon, A.,"Behavior of Large Panel Precast Coupled Wall Systems Subjected to Earthquake Loading," PCI Journal, Vol. 33, No. 5, 1988, pp. 124-151
  2. 한국콘크리트학회, 콘크리트 구조설계기준, 한국콘크리트학회, 2007, pp. 109-136
  3. Comite Euro International Du, CEB-FIP Model Code, Beton, Thomas Telford, pp. 82-115
  4. PCI, PCI Design Handbook, 6th Edition, Precast Concrete Institute, 2004, pp. 6-1-73
  5. ACI Committee 318, Building Code Requirements for Reinforced Concrete (ACI 318-05), American Concrete Institute, Detroit, 2005, pp. 12-1-26
  6. Hansen, K., Kavyrchine, M., Melhorn, G., Olesen, S., Pume, D., and Schwing, H., "Design of Vertical Keyed Shear Joints in Large Panel Buildings," Building Research and Information, Vol. 2, No. 4, 1974, pp. 202-215 https://doi.org/10.1080/09613217408550318
  7. Chakrabarti, S. C., Nayak, G. C., and Paul, D. K., "Shear Characteristics of Cast-in-place Vertical Joints in Story-high Precast Wall Assembly," ACI Structural Journal, Vol. 85, No. 1, 1988, pp. 30-45
  8. Chen, W. F. and Han, D. J., Plasticity for Structural Engineers, Springer-Verlag New York Inc., 1988, pp. 176-230
  9. Hashim, M. S., Abdul-Wahab, and Sinan Y. H. Sarsam, "Prediction of Ultimate Shear Strength of Vertical Joints in Large Panel Structures," ACI Structural Journal, Vol. 88, No. 2, 1991, pp. 204-213
  10. Tassios, T. P. and Tsoukantas, S. G., "Behavior of Large Panel Connections," Building Research and Practice, Vol. 12, No. 4, 1983, pp. 226-232

Cited by

  1. Development and Seismic Performance of Vertical Joints in Precast Concrete Shear Walls under Cyclic Loads vol.16, pp.1, 2012, https://doi.org/10.11112/jksmi.2012.16.1.140