DOI QR코드

DOI QR Code

Effect of Nozzle Geometry on the Suction Flow Rate in a Ejector

이젝터의 노즐 형상이 흡입유량에 미치는 영향

  • Published : 2009.12.01

Abstract

Ejector is an equipment devised for making use of the low pressure occurring from the fast fluid injection and it is a transportation equipment which can obtain vacuum using the kinetic energy of the fluid. This ejector system is, nowadays, widely used for construction machinery, heavy equipments, the cooling and ventilation of electronic devices and for the various fluid transportation and pumps. In this study, it is attempted to perform a numerical analysis and an experiment to find out the characteristics of fluid quantity, velocity and the pressure distribution of the induction pipe by changing the length and the radius ratio of the nozzle of ejector. From the results, it is investigated that the distributions of velocity and pressure of induction pipe attached are changing with the length and the radius ratio of the nozzle. In addition, it is shown that for the small and large ejector, the efficiency is the maximum when the length of the nozzle arrived to the neck of the ejector, however, if it is installed at below or above the neck the efficiency is rather decreased.

Keywords

References

  1. D. K. Acharjee, A. K. Mirra and A. N. Roy, 1978, 'Co-Current flow Liquid Binary Mass Trnsfer in Ejector,' The Canadian Journal of Chemical Engineering, vol. 56, February, pp. 33-42 https://doi.org/10.1002/cjce.5450560106
  2. Sun. D.W. and Eames. I.E., 1995, 'Recent developments in the design the-ories and applocations of Ejectors-a review,' Journal of the Institute of Energy, Vol. 68, June, pp. 665-676
  3. Witte, J.H., 1965, 'Efficiency and design of liquid-gas ejector,' British-chemical Engineering, Vol. 10, No. 9, pp. 602-607
  4. Biswas, M.N, and Mitra, A.K., 1989, 'Momentum Transfer in Horizontal Engineering Multi-jet liquid-gas ejector,' The Canadian Journal of Chemical Engieering, Vol. 59, pp.634-637 https://doi.org/10.1002/cjce.5450590513
  5. Peter Menegay and Alan A. Kornhauser, 1996, 'Improvements to The Ejector Expansion Refrigeration Cycle,' IEEE, pp. 702-706
  6. Tillman, T. G. and Presz Jr., W. M., 1995, 'Thrust Characteristics of a Supersonic Mixer Ejector,' Jour. Propulsion and Powers, Vol. 11, No. 5, pp. 931-937 https://doi.org/10.2514/3.23919
  7. Dutton, J. C. and Carroll, B. F., 1983, 'Optimized Ejector - Diffuser Design Procedure for Natural Gas Vapor Recovery,' Journal of Energy Resources Technology, Vol. 105, pp. 388-393 https://doi.org/10.1115/1.3230934
  8. Kim, H. D., Lee, H. J., Lee, Y. K. and Seo, T. W., 1999, 'A CFD Study of Axisymmetric Supersonic Ejector-Pump System,' KSPE Fall Annual Meeting, pp. 36
  9. Lee, Y. K., Kim, H. D. and Seo, T. W., 1999, 'A CFD Study of the Supersonic Ejector-Pump Flows,' KSPE Jour, Vol. 3, No. 4, pp. 58-66

Cited by

  1. Numerical Analysis of the Flow Characteristics of High-Pressure Injection Nozzle for Machine Tools vol.35, pp.10, 2011, https://doi.org/10.3795/KSME-B.2011.35.10.1061