Korean Journal of Metals and Materials (대한금속재료학회지)

The Korean Institute of Metals and Materials (대한금속재료학회)
권호 표지

Creep Properties of Squeeze Infiltrated AS52 Mg/Al18B4O33w Composite

용탕가압침투 AS52 Mg/Al18B4O33w 복합재료의 크리프 특성

  • Choi, Kye-Won (Department of Materials Science and Engineering, Pusan National University) ;
  • Park, Yong-Ha (Department of Materials Science and Engineering, Pusan National University) ;
  • Park, Bong-Gyu (Department of Materials Science and Engineering, Pusan National University) ;
  • Park, Yong-Ho (Department of Materials Science and Engineering, Pusan National University) ;
  • Park, Ik-Min (Department of Materials Science and Engineering, Pusan National University) ;
  • Cho, Kyung-Mox (Department of Materials Science and Engineering, Pusan National University)
  • Received : 2008.03.20
  • Published : 2008.07.25
⟨ Previous Next ⟩

Abstract

Creep behavior of the squeeze infiltrated AS52 Mg matrix composites reinforced with 15 vol% of aluminum borate whiskers($Al_{18}B_4O_{33}w$) fabricated squeeze infiltration method was investigated. Microstructure of the composites was observed as uniformly distributed reinforcement in the matrix without any particular defects of casting pores etc.. Creep test was carried out at the temperature of 150 and $200^{\circ}C$ under the applied stress range of 60~120 MPa. The creep resistance of the composite was significantly improved comparing with the unreinforced AS52 Mg alloy. The creep behavior of composites might be interpreted with the substructure invariant model successfully for the composite. Threshold stress of the composite exist for the creep deformation of the composite. The analysis of the creep behavior of the composite with threshold stress indicated that creep deformation was controlled by the lattice diffusion process of AS52 Mg matrix at given effective stresses and temperatures. Activation energy was also calculated to check lattice diffusion controlled creep behavior of the composite.

Keywords

Acknowledgement

Supported by : 부산대학교

References

  1. A. Stalmann, W. Sebastian, H. Friedrich, S. Schumann, Adv. Eng. Mater. 3, 969 (2001) https://doi.org/10.1002/1527-2648(200112)3:12<969::AID-ADEM969>3.0.CO;2-9
  2. H. Friedrich, S. Schumann, Mater. Sci. Forum. 419, 51 (2003)
  3. B. Jing, S. Yangshan, Meter. Sci. Eng. A419, 181 (2006)
  4. I. J. Polmear, Mater. Sci. Tech. 10, 1 (1994) https://doi.org/10.1179/026708394790163401
  5. S. Ugadhar, M. Gupta, S. K. Sinha, Compo. Struc. 72, 256 (2006)
  6. B, L. Mordike, T. Ebert, Mater. Sci. Eng. A302, 37(2001)
  7. G. Y. Yuan, Z. L. Liu, Meter. Letters 56, 53 (2002) https://doi.org/10.1016/S0167-577X(02)00417-2
  8. I. J. Polmear, Light Alloys, Third ed., Anold, a division of Hodder Headline PLC, London (1995)
  9. Y. Shintari, Y. Okochi, M. Sugiyama, Proc. 5th International SAMPLE Symposium, p. 339, Japan (1997)
  10. N. Chawla, K. K. Chawla, Metal Metrix Composites, Springer p.305 (2006)
  11. S. S. Vagarali, T. G. Langdon, Acta Metall. 29, 1969 (1981) https://doi.org/10.1016/0001-6160(81)90034-1
  12. S. S. Vagarali, T. G. Langdon, Acta Metall. 30, 1157 (1982) https://doi.org/10.1016/0001-6160(82)90009-8
  13. K. T. Park, E. J. Lavernia, F. A. Mohamed, Acta Met. Mat. 38, 2149 (1990) https://doi.org/10.1016/0956-7151(90)90082-R
  14. Y. Li, G. Langdon. Acta Mater. 45, 4797 (1997) https://doi.org/10.1016/S1359-6454(97)00132-8
  15. F. A. Mohamed, T. G. Langdon, Acta. Metall. 22, 779 (1974) https://doi.org/10.1016/0001-6160(74)90088-1
  16. O. D. Sherby, R. H. Klundt, A. K. Miller, Metall. Trans. 8, 843 (1997)
  17. F.A. Mohamed, K. T. Park, E. J. Lavernia, Mater. Sci. Eng. A150, 21 (1992)
  18. Y. Li, T. G. Langdon, Acta. Mater. 46, 3937(1998) https://doi.org/10.1016/S1359-6454(98)00073-1