References
- Tajika, M., Rafaniello, W., and Niihara, K., 2000, "Sintering behavior of direct nitride AlN powder," Materials Letters, Vol. 46, pp. 98-104 https://doi.org/10.1016/S0167-577X(00)00149-X
-
Zhao, H., Wang, W., Fu, Z., and Wang, H., 2008, "Thermal conductivity and dielectric property of hotpressing sintered AIN-BN ceramic composites," Ceram. Int., viewed 20 January 2008,
- Werdecker, W. and Aldinger, F., 1984, "Aluminum Nitride-An Alternative Ceramic Substrate for High Powder Application in Microcircuits," IEEE Trans. Components Hybrids Manuf. Technol., Vol. CHMT-7, No. 4, pp. 399-404
-
Cho, M. W., Kim, D. W., Cho., W. S., Park, D, S., and Lee, J., 2007, "Micro Groove Machining Characteristics of
$Si_3N_4-hBN$ Composites," Key Engineering Materials, Vol. 336-338, pp. 1461-1464 https://doi.org/10.4028/www.scientific.net/KEM.336-338.1461 -
Park, D. S., Cho, M. W., Kim, D. W., and Cho, W. S., 2004, "Micro-Pattern Machining Characteristics Evaluation of
$Si_3N_4$ -hBN based Machinable Ceramics Using Powder Blasting Process," Trans. of KSMTE., Vol. 13, No. 2, pp. 33-39 - Cho,W. S., Piao, Z. H., Yoo, Y. C., Lee, T. C., Cho, M. W., Hong, Y. C., Park, K., and Hwang, W.S., 2007, "Microstructure and mechanical properties of AlN-hBN based machinable ceramics prepared by pressureless sintering," J. Europ. Ceram. Soc., Vol. 27, pp. 1425-1430 https://doi.org/10.1016/j.jeurceramsoc.2006.05.044
- Gam, J. S., Ha, J. S., Cheong, D. S. and Han, K. S., 1994, "Machinability and Strength of AlN-BN Ceramics," J. Kor. Ceram. Soc., Vol. 31, No. 2, pp. 177-184
- Beck, S. Y., Cho, M. W., and Cho, W. S., 2008, "Mechanical Properties and End-milling Characteristic of AlN-hBN Based Machinable Ceramics," J. Kor. Ceram. Soc., Vol. 45, No. 1, pp. 75-81 https://doi.org/10.4191/KCERS.2008.45.1.075
- Cao, Y., 2001, "Failure analysis of exit edges in ceramic machining using finite element analysis," Engineering Failure Analysis, Vol. 8, pp. 325-338 https://doi.org/10.1016/S1350-6307(00)00024-8
-
Jang, S. M. and Cho, M. W., 2004, "Surface Properties and Tool Wear of
$Si_3N_4$ -hBN Machinable Ceramics in Endmill Machining using Tungsten Carbide Tool," J. Kor. Soci. Manuf. Pro. Eng., Vol. 3, No. 1, pp. 15-21 -
Cho, M. W., Kim, D. W., and Cho, W. S., 2007, "Analysis of micro-machining characteristics of
$Si_3N_4$ -hBN composites," Journal of European Ceramic Society, Vol. 27, pp. 1259-1265 https://doi.org/10.1016/j.jeurceramsoc.2006.08.002 - Lai, X., Li, H., Li, C., Lin, Z., and Ni, J., 2008, "Modelling and analysis of micro scale milling considering size effect, micro cutter edge radius and minium chip thickness," Int. J. Mach. Tools & Manuf., Vol. 48, pp. 1-14 https://doi.org/10.1016/j.ijmachtools.2007.08.011