DOI QR코드

DOI QR Code

소결온도 및 SiO2 첨가량에 따른 탄화규소의 마모 특성

Wear Characteristics of SiC by Sintered Temperature and SiO2 Contents

  • 박성호 (경상대학교 대학원 정밀기계공학과) ;
  • 박원조 (경상대학교 기계항공공학부, 해양산업연구소) ;
  • 윤한기 (동의대학교 기계공학과)
  • 발행 : 2008.11.01

초록

In this study, liquid phase sintered SiC (LPS-SiC) materials were made by hot pressing method. The particle size of nano-SiC powder was 30nm. Alumina ($Al_2O_3$), yttria ($Y_2O_3$) and silica ($SiO_2$) were used for sintering additives. To investigate effects of $SiO_2$, ratios of $SiO_2$ contents were changed by five kinds. Materials have been sintered for 1 hour at $1760^{\circ}C$, $1780^{\circ}C$ and $1800^{\circ}C$ under the pressure of 20MPa. The system of sintering additives which affects a property of sintering as well as the influence depending on compositions of sintering additives were investigated by measurement of density, mechanical properties such as flexural strength, vickers hardness and sliding wear resistance were investigated to make sure of the optimum condition which is about matrix of $SiC_f$/SiC composites. The abrasion test condition apply to load of 20N at 100RPM for 20min. Sintered density, flexural strength of fabricated LPS-SiC increased with increasing the sintering temperature. And in case of LPS-SiC with low $SiO_2$, sliding wear resistance has very excellent. Monolithic SiC $1800^{\circ}C$ sintering temperatures and 3wt% have excellent wear resistance.

키워드

참고문헌

  1. Kaya, H., 1999, "The Application Of Ceramic-Matrix Composites To The Automotive Ceramic Gas Turbine," Composites Science and Technology, Vol. 59, pp. 861 ~ 872 https://doi.org/10.1016/S0266-3538(99)00016-0
  2. Sato, K., Tezuka, A., Funayama, O., Isoda, T., Terada, Y., Kato, S. and Iwata, M., 1999, "Fabrication and Pressure Testing Of A Gas-Turbine Component Manufactured By A Preceramic-Polymer-Impregnation Method," Composites Science and Technology, Vol. 59, pp. 853 ~ 859 https://doi.org/10.1016/S0266-3538(99)00015-9
  3. Snead, L. L., Jones, R. H., Kohyama, A. and Fenici, P., 1996, "Status of Silicon Carbide Composites For Fusion," Journal of Nuclear Materials, Vol. 233-237, pp. 26~36 https://doi.org/10.1016/S0022-3115(96)00318-2
  4. Raffray, A. R., Jones, R., Aiello, G., Billone, M., Giancarli, L., Golfier, H., Hasegawa, A., Katoh, Y., Kohyama, A., Nishio, S., Riccardi, B. and Tillack, M. S., 2001, "Design and Material Issues For High Performance SiCf/SiC-Based Fusion Power Cores," Fusion Engineering and Design, Vol. 55, pp. 55~95 https://doi.org/10.1016/S0920-3796(01)00181-8
  5. Ohring, M., Engineering Materilas Science (Academic Press, USA 1995).
  6. Park, S. H., Shin, D. I., Park, W. J., Lee, K. Y., Huh, S. C., 2003, "A Study on Fraction and Wear Properties of $MoSi_2$ Composites," KSME Spring Annual Meeting. pp. 175~180
  7. Yano, T., Park, D. C., Horie, Y., Inoue, H., Katayama, K. and Iseki, T., Key Eng. Mater. Vol. 247(2003), p. 165 https://doi.org/10.4028/www.scientific.net/KEM.247.165
  8. Ren, J. R., Kim, K. H. and Kim, S. S., 2001, "Tribological Evaluation of Dental Composite ResinsContaining Prepolymerized Particle Fillers," KSME International Journal, Vol. 15 No. 6, pp. 727~734