References
- Chun, M. H. and Kang, M. G., 1998, "Effects of Heat Exchanger Tube Parameters on Nucleate Pool Boiling Heat Transfer," ASME, J. of Heat Transfer, Vol. 120, pp. 468-476 https://doi.org/10.1115/1.2824272
- Corletti, M. M. and Hochreiter, L. E., 1991, "Advanced Light Water Reactor Passive Residual Heat Removal Heat Exchanger Test," Proc. of the 1st JSME/ASME Joint International Conference on Nuclear Engineering, Tokyo, Japan, pp. 381-387
- Kang, M. G., 1998, "Experimental Investigation of Tube Length Effect on Nucleate Pool Boiling Heat Transfer," Annals of Nuclear Energy, Vol. 25, No. 4-5, pp. 295-304 https://doi.org/10.1016/S0306-4549(97)00056-X
- Kang, M. G., 2002, Effects of Tube Inclination Angle on Nucleate Pool Boiling Heat Transfer, Trans. KSME B, Vol. 26, No. 1, pp. 116-124 https://doi.org/10.3795/KSME-B.2002.26.1.116
- Jakob, M. and Hawkins, G. A., 1957, Elements of Heat Transfer, 3rd. ed., Wiley International Edition, pp. 206-210
- Van Stralen, S. J. D. and Sluyter, W. M. 1969, "Investigations on the Critical Heat Flux of Pure Liquids and Mixtures under Various Conditions," Int. J. Heat Mass Transfer, Vol. 12, pp. 1353-1384 https://doi.org/10.1016/0017-9310(69)90022-2
- Githinji, P. M. and Sabersky, R. H., 1963, "Some Effects of the Orientation of the Heating Surface in Nucleate Boiling" ASME, J. of Heat Transfer, Vol. 85, p. 379 https://doi.org/10.1115/1.3686129
- Nishikawa, K., Fujita, Y., Uchida, S. and Ohta, H., 1984, "Effect of Surface Configuration on Nucleate Boiling Heat Transfer," Int. J. Heat Mass Transfer, Vol. 27, No. 9, pp. 1559-1571 https://doi.org/10.1016/0017-9310(84)90268-0
- Jung, D. S., Venant, J. E. S. and Sousa, A. C. M., 1987, "Effects of Enhanced Surfaces and Surface Orientations on Nucleate and Film Boiling Heat Transfer in R-11," Int. J. Heat Mass Transfer, Vol. 30, No. 12, pp. 2627-2639 https://doi.org/10.1016/0017-9310(87)90144-X
- Fujita, Y., Ohta, H., Uchida, S., and Nishikawa, K., 1988, "Nucleate Boiling Heat Transfer and Critical Heat Flux in Narrow Space Between Rectabgular Spaces," Int. J. of Heat Mass Transfer, Vol. 31, No. 2, pp. 229-239 https://doi.org/10.1016/0017-9310(88)90004-X
- Howard, A. H. and Mudawar, I., 1999, "Orientation Effects on Pool Boiling Critical Heat Flux(CHF) and Modeling of CHF for Near-Vertical Surfaces," Int. J. Heat Mass Transfer, Vol. 42, pp. 1665-1688 https://doi.org/10.1016/S0017-9310(98)00233-6
- El-Genk, M. S. and Bostanci H., 2003, "Saturation Boiling of HFE-7100 from a Copper Surface, Simulating a Microelectric Chip," Int. J. Heat Mass Transfer, Vol. 46, pp. 1841-1854 https://doi.org/10.1016/S0017-9310(02)00489-1
- Chyu, M. C. and Mghamis, A. M., 1991, "Nucleate Boiling on Two Cylinders in Line Contact," Int. J. Heat Mass Transfer, Vol. 34, No. 7, pp. 1783-1790 https://doi.org/10.1016/0017-9310(91)90153-6
- Cornwell, K. and Houston, S. D., 1994, "Nu cleate Pool Boiling on Horizontal Tubes: a Convection-Based Correlation," Int. J. Heat Mass Transfer, Vol. 37, Suppl. 1, pp. 303-309 https://doi.org/10.1016/0017-9310(94)90031-0
- Kang, M. G., 2000, "Effect of Tube Inclination on Pool Boiling Heat Transfer," ASME, J. of Heat Transfer, Vol. 122, Issue 1, pp. 188-192 https://doi.org/10.1115/1.521456